diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index e7d0ddfe25a..39379428b85 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -511,11 +511,11 @@ config KS8851_MLL
 	  The Microchip KS8851 parallel bus external ethernet interface chip.
 
 config KSZ9477
-	bool "Microchip KSZ9477 I2C controller driver"
-	depends on DM_DSA && DM_I2C
+	bool "Microchip KSZ9477 controller driver"
+	depends on DM_DSA && (DM_I2C || DM_SPI)
 	help
 	  This driver implements a DSA switch driver for the KSZ9477 family
-	  of GbE switches using the I2C interface.
+	  of GbE switches using the I2C or SPI interface.
 
 config LITEETH
 	bool "LiteX LiteEth Ethernet MAC"
diff --git a/drivers/net/ksz9477.c b/drivers/net/ksz9477.c
index 1190b591fcb..7ebbe197660 100644
--- a/drivers/net/ksz9477.c
+++ b/drivers/net/ksz9477.c
@@ -14,6 +14,9 @@
 #if CONFIG_IS_ENABLED(DM_I2C)
 # include <i2c.h>
 #endif
+#if CONFIG_IS_ENABLED(DM_SPI)
+# include <spi.h>
+#endif
 #include <net/dsa.h>
 
 #include <asm-generic/gpio.h>
@@ -73,6 +76,14 @@
 #define MMD_SETUP(mode, dev)		(((u16)(mode) << PORT_MMD_OP_MODE_S) | (dev))
 #define REG_PORT_PHY_MMD_INDEX_DATA	0x011C
 
+/* SPI specific define (opcodes) */
+#define KSZ_SPI_OP_RD			3
+#define KSZ_SPI_OP_WR			2
+
+#define KSZ9477_SPI_ADDR_SHIFT		24
+#define KSZ9477_SPI_ADDR_ALIGN		3
+#define KSZ9477_SPI_TURNAROUND_SHIFT	5
+
 /**
  * struct ksz_phy_ops - low-level KSZ bus operations
  */
@@ -124,6 +135,92 @@ static struct ksz_phy_ops phy_i2c_ops = {
 };
 #endif
 
+#if CONFIG_IS_ENABLED(DM_SPI)
+/**
+ * ksz_spi_xfer() - only used for 8/16/32 bits bus access
+ *
+ * @dev:	The SPI slave device which will be sending/receiving the data.
+ * @reg:	register address.
+ * @out:	Pointer to a string of bits to send out.  The bits are
+ *		held in a byte array and are sent MSB first.
+ * @in:		Pointer to a string of bits that will be filled in.
+ * @len:	number of bytes to read.
+ *
+ * Return: 0 on success, not 0 on failure
+ */
+static int ksz_spi_xfer(struct udevice *dev, u32 reg, const u8 *out,
+			u8 *in, u16 len)
+{
+	int ret;
+	u32 addr = 0;
+	u8 opcode;
+
+	if (in && out) {
+		printf("%s: can't do full duplex\n", __func__);
+		return -EINVAL;
+	}
+
+	if (len > 4 || len == 0) {
+		printf("%s: only 8/16/32 bits bus access supported\n",
+		       __func__);
+		return -EINVAL;
+	}
+
+	ret = dm_spi_claim_bus(dev);
+	if (ret < 0) {
+		printf("%s: could not claim bus\n", __func__);
+		return ret;
+	}
+
+	opcode = (in ? KSZ_SPI_OP_RD : KSZ_SPI_OP_WR);
+
+	/* The actual device address space is 16 bits (A15 - A0),
+	 * so the values of address bits A23 - A16 in the SPI
+	 * command/address phase are “don't care”.
+	 */
+	addr |= opcode << (KSZ9477_SPI_ADDR_SHIFT + KSZ9477_SPI_TURNAROUND_SHIFT);
+	addr |= reg << KSZ9477_SPI_TURNAROUND_SHIFT;
+
+	addr = __swab32(addr);
+
+	ret = dm_spi_xfer(dev, 32, &addr, NULL, SPI_XFER_BEGIN);
+	if (ret) {
+		printf("%s ERROR: dm_spi_xfer addr (%u)\n", __func__, ret);
+		goto release_bus;
+	}
+
+	ret = dm_spi_xfer(dev, len * 8, out, in, SPI_XFER_END);
+	if (ret) {
+		printf("%s ERROR: dm_spi_xfer data (%u)\n", __func__, ret);
+		goto release_bus;
+	}
+
+release_bus:
+	/* If an error occurred, release the chip by deasserting the CS */
+	if (ret < 0)
+		dm_spi_xfer(dev, 0, NULL, NULL, SPI_XFER_END);
+
+	dm_spi_release_bus(dev);
+
+	return ret;
+}
+
+static inline int ksz_spi_read(struct udevice *dev, u32 reg, u8 *val, int len)
+{
+	return ksz_spi_xfer(dev, reg, NULL, val, len);
+}
+
+static inline int ksz_spi_write(struct udevice *dev, u32 reg, u8 *val, int len)
+{
+	return ksz_spi_xfer(dev, reg, val, NULL, len);
+}
+
+static struct ksz_phy_ops phy_spi_ops = {
+	.read = ksz_spi_read,
+	.write = ksz_spi_write,
+};
+#endif
+
 static inline int ksz_read8(struct udevice *dev, u32 reg, u8 *val)
 {
 	struct ksz_dsa_priv *priv = dev_get_priv(dev);
@@ -602,6 +699,12 @@ static int ksz_probe(struct udevice *dev)
 		}
 		break;
 	}
+#endif
+#if CONFIG_IS_ENABLED(DM_SPI)
+	case UCLASS_SPI: {
+		ksz_ops_register(dev, &phy_spi_ops);
+		break;
+	}
 #endif
 	default:
 		dev_err(dev, "invalid parent bus (%s)\n",