Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'

include/configs/embestmx6boards.h

@@ -20,7 +20,7 @@
 #include <linux/sizes.h>
 
 #define CONFIG_MXC_UART_BASE		UART2_BASE
-#define CONFIG_CONSOLE_DEV		"ttymxc0"
+#define CONFIG_CONSOLE_DEV		"ttymxc1"
 #define CONFIG_MMCROOT			"/dev/mmcblk1p2"
 
 #define PHYS_SDRAM_SIZE		(1u * 1024 * 1024 * 1024)
@@ -293,7 +293,7 @@
 
 #if defined(CONFIG_ENV_IS_IN_MMC)
 /* RiOTboard */
-#define CONFIG_DEFAULT_FDT_FILE	"imx6s-riotboard.dtb"
+#define CONFIG_DEFAULT_FDT_FILE	"imx6dl-riotboard.dtb"
 #define CONFIG_SYS_FSL_USDHC_NUM	3
 #define CONFIG_SYS_MMC_ENV_DEV		2	/* SDHC4 */
 #define CONFIG_ENV_OFFSET		(6 * 64 * 1024)

include/configs/gw_ventana.h

@@ -7,6 +7,17 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
+/* SPL */
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_FAT_SUPPORT
+/*
+#define CONFIG_SPL_SATA_SUPPORT
+*/
+/* Location in NAND to read U-Boot from */
+#define CONFIG_SYS_NAND_U_BOOT_OFFS     (14 * 1024 * 1024)
+
+#include "imx6_spl.h"                  /* common IMX6 SPL configuration */
 #include "mx6_common.h"
 #define CONFIG_MX6
 #define CONFIG_DISPLAY_CPUINFO         /* display cpu info */

include/configs/imx6_spl.h

@@ -0,0 +1,71 @@
+/*
+ * Copyright (C) 2014 Gateworks Corporation
+ * Author: Tim Harvey <tharvey@gateworks.com>
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+#ifndef __IMX6_SPL_CONFIG_H
+#define __IMX6_SPL_CONFIG_H
+
+#ifdef CONFIG_SPL
+
+#define CONFIG_SPL_FRAMEWORK
+
+/*
+ * see Figure 8-3 in IMX6DQ/IMX6SDL Reference manuals:
+ *  - IMX6SDL OCRAM (IRAM) is from 0x00907000 to 0x0091FFFF
+ *  - IMX6DQ has 2x IRAM of IMX6SDL but we intend to support IMX6SDL as well
+ *  - BOOT ROM stack is at 0x0091FFB8
+ *  - if icache/dcache is enabled (eFuse/strapping controlled) then the
+ *    IMX BOOT ROM will setup MMU table at 0x00918000, therefore we need to
+ *    fit between 0x00907000 and 0x00918000.
+ *  - Additionally the BOOT ROM loads what they consider the firmware image
+ *    which consists of a 4K header in front of us that contains the IVT, DCD
+ *    and some padding thus 'our' max size is really 0x00908000 - 0x00918000
+ *    or 64KB
+ */
+#define CONFIG_SPL_LDSCRIPT	"arch/arm/cpu/armv7/omap-common/u-boot-spl.lds"
+#define CONFIG_SPL_TEXT_BASE		0x00908000
+#define CONFIG_SPL_MAX_SIZE		(64 * 1024)
+#define CONFIG_SPL_START_S_PATH		"arch/arm/cpu/armv7"
+#define CONFIG_SPL_STACK		0x0091FFB8
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_GPIO_SUPPORT
+
+/* NAND support */
+#if defined(CONFIG_SPL_NAND_SUPPORT)
+#define CONFIG_SPL_NAND_MXS
+#define CONFIG_SPL_DMA_SUPPORT
+#endif
+
+/* MMC support */
+#if defined(CONFIG_SPL_MMC_SUPPORT)
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	138 /* offset 69KB */
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS	800 /* 400 KB */
+#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION	1
+#define CONFIG_SYS_MONITOR_LEN  (CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS/2*1024)
+#endif
+
+/* SATA support */
+#if defined(CONFIG_SPL_SATA_SUPPORT)
+#define CONFIG_SPL_SATA_BOOT_DEVICE		0
+#define CONFIG_SYS_SATA_FAT_BOOT_PARTITION	1
+#endif
+
+/* Define the payload for FAT/EXT support */
+#if defined(CONFIG_SPL_FAT_SUPPORT) || defined(CONFIG_SPL_EXT_SUPPORT)
+#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME  "u-boot.img"
+#define CONFIG_SPL_LIBDISK_SUPPORT
+#endif
+
+#define CONFIG_SPL_BSS_START_ADDR	0x18200000
+#define CONFIG_SPL_BSS_MAX_SIZE		0x100000	/* 1 MB */
+#define CONFIG_SYS_SPL_MALLOC_START	0x18300000
+#define CONFIG_SYS_SPL_MALLOC_SIZE	0x3200000	/* 50 MB */
+#define CONFIG_SYS_TEXT_BASE		0x17800000
+#endif
+
+#endif

include/configs/m53evk.h

@@ -9,6 +9,7 @@
 #define __M53EVK_CONFIG_H__
 
 #define CONFIG_MX53
+#define CONFIG_SYS_GENERIC_BOARD
 #define CONFIG_MXC_GPIO
 
 #include <asm/arch/imx-regs.h>

include/configs/mx28evk.h

@@ -48,7 +48,11 @@
 #define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
 
 /* Environment */
+#ifndef CONFIG_ENV_IS_IN_SPI_FLASH
 #define CONFIG_ENV_SIZE			(16 * 1024)
+#else
+#define CONFIG_ENV_SIZE			(4 * 1024)
+#endif
 #define CONFIG_ENV_OVERWRITE
 
 /* Environment is in MMC */
@@ -70,7 +74,6 @@
 /* Environemnt is in SPI flash */
 #if defined(CONFIG_CMD_SF) && defined(CONFIG_ENV_IS_IN_SPI_FLASH)
 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
-#define CONFIG_ENV_SIZE			0x1000		/* 4KB */
 #define CONFIG_ENV_OFFSET		0x40000		/* 256K */
 #define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
 #define CONFIG_ENV_SECT_SIZE		0x1000

include/configs/mx6_common.h

@@ -17,7 +17,6 @@
 #ifndef __MX6_COMMON_H
 #define __MX6_COMMON_H
 
-#define CONFIG_ARM_ERRATA_742230
 #define CONFIG_ARM_ERRATA_743622
 #define CONFIG_ARM_ERRATA_751472
 #define CONFIG_ARM_ERRATA_794072

include/configs/mx6qsabreauto.h

@@ -12,7 +12,11 @@
 #define CONFIG_MACH_TYPE	3529
 #define CONFIG_MXC_UART_BASE	UART4_BASE
 #define CONFIG_CONSOLE_DEV		"ttymxc3"
+#if defined CONFIG_MX6Q
 #define CONFIG_DEFAULT_FDT_FILE	"imx6q-sabreauto.dtb"
+#elif defined CONFIG_MX6DL
+#define CONFIG_DEFAULT_FDT_FILE	"imx6dl-sabreauto.dtb"
+#endif
 #define CONFIG_MMCROOT			"/dev/mmcblk0p2"
 #define PHYS_SDRAM_SIZE		(2u * 1024 * 1024 * 1024)
 

include/configs/mx6sabresd.h

@@ -59,4 +59,16 @@
 #define CONFIG_PCIE_IMX_POWER_GPIO	IMX_GPIO_NR(3, 19)
 #endif
 
+/* I2C Configs */
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_SPEED		  100000
+
+/* PMIC */
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+#define CONFIG_POWER_PFUZE100
+#define CONFIG_POWER_PFUZE100_I2C_ADDR	0x08
+
 #endif                         /* __MX6QSABRESD_CONFIG_H */

include/power/pfuze100_pmic.h

@@ -15,7 +15,11 @@ enum {
 	PFUZE100_FABID		= 0x04,
 
 	PFUZE100_SW1ABVOL	= 0x20,
+	PFUZE100_SW1ABSTBY	= 0x21,
+	PUZE_100_SW1ABCONF	= 0x24,
 	PFUZE100_SW1CVOL	= 0x2e,
+	PFUZE100_SW1CSTBY	= 0x2f,
+	PFUZE100_SW1CCONF	= 0x32,
 	PFUZE100_SW2VOL		= 0x35,
 	PFUZE100_SW3AVOL	= 0x3c,
 	PFUZE100_SW3BVOL	= 0x43,