Merge branch 'master' of git://www.denx.de/git/u-boot-imx

drivers/i2c/mxc_i2c.c

@@ -581,8 +581,16 @@ void bus_i2c_init(int index, int speed, int unused,
 		return;
 	}
 
-	mxc_i2c_buses[index].idle_bus_fn = idle_bus_fn;
-	mxc_i2c_buses[index].idle_bus_data = idle_bus_data;
+	/*
+	 * Warning: Be careful to allow the assignment to a static
+	 * variable here. This function could be called while U-Boot is
+	 * still running in flash memory. So such assignment is equal
+	 * to write data to flash without erasing.
+	 */
+	if (idle_bus_fn)
+		mxc_i2c_buses[index].idle_bus_fn = idle_bus_fn;
+	if (idle_bus_data)
+		mxc_i2c_buses[index].idle_bus_data = idle_bus_data;
 
 	ret = enable_i2c_clk(1, index);
 	if (ret < 0) {

drivers/mmc/fsl_esdhc.c

@@ -502,15 +502,22 @@ static void set_sysctl(struct mmc *mmc, uint clock)
 
 	clk = (pre_div << 8) | (div << 4);
 
+#ifdef CONFIG_FSL_USDHC
+	esdhc_setbits32(&regs->sysctl, SYSCTL_RSTA);
+#else
 	esdhc_clrbits32(&regs->sysctl, SYSCTL_CKEN);
+#endif
 
 	esdhc_clrsetbits32(&regs->sysctl, SYSCTL_CLOCK_MASK, clk);
 
 	udelay(10000);
 
-	clk = SYSCTL_PEREN | SYSCTL_CKEN;
+#ifdef CONFIG_FSL_USDHC
+	esdhc_clrbits32(&regs->sysctl, SYSCTL_RSTA);
+#else
+	esdhc_setbits32(&regs->sysctl, SYSCTL_PEREN | SYSCTL_CKEN);
+#endif
 
-	esdhc_setbits32(&regs->sysctl, clk);
 }
 
 #ifdef CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK
@@ -585,7 +592,9 @@ static int esdhc_init(struct mmc *mmc)
 	esdhc_write32(&regs->scr, 0x00000040);
 #endif
 
+#ifndef CONFIG_FSL_USDHC
 	esdhc_setbits32(&regs->sysctl, SYSCTL_HCKEN | SYSCTL_IPGEN);
+#endif
 
 	/* Set the initial clock speed */
 	mmc_set_clock(mmc, 400000);
@@ -657,8 +666,10 @@ int fsl_esdhc_initialize(bd_t *bis, struct fsl_esdhc_cfg *cfg)
 	/* First reset the eSDHC controller */
 	esdhc_reset(regs);
 
+#ifndef CONFIG_FSL_USDHC
 	esdhc_setbits32(&regs->sysctl, SYSCTL_PEREN | SYSCTL_HCKEN
 				| SYSCTL_IPGEN | SYSCTL_CKEN);
+#endif
 
 	writel(SDHCI_IRQ_EN_BITS, &regs->irqstaten);
 	memset(&cfg->cfg, 0, sizeof(cfg->cfg));

drivers/net/fec_mxc.c

@@ -131,13 +131,25 @@ static void fec_mii_setspeed(struct ethernet_regs *eth)
 	/*
 	 * Set MII_SPEED = (1/(mii_speed * 2)) * System Clock
 	 * and do not drop the Preamble.
+	 *
+	 * The i.MX28 and i.MX6 types have another field in the MSCR (aka
+	 * MII_SPEED) register that defines the MDIO output hold time. Earlier
+	 * versions are RAZ there, so just ignore the difference and write the
+	 * register always.
+	 * The minimal hold time according to IEE802.3 (clause 22) is 10 ns.
+	 * HOLDTIME + 1 is the number of clk cycles the fec is holding the
+	 * output.
+	 * The HOLDTIME bitfield takes values between 0 and 7 (inclusive).
+	 * Given that ceil(clkrate / 5000000) <= 64, the calculation for
+	 * holdtime cannot result in a value greater than 3.
 	 */
-	register u32 speed = DIV_ROUND_UP(imx_get_fecclk(), 5000000);
+	u32 pclk = imx_get_fecclk();
+	u32 speed = DIV_ROUND_UP(pclk, 5000000);
+	u32 hold = DIV_ROUND_UP(pclk, 100000000) - 1;
 #ifdef FEC_QUIRK_ENET_MAC
 	speed--;
 #endif
-	speed <<= 1;
-	writel(speed, &eth->mii_speed);
+	writel(speed << 1 | hold << 8, &eth->mii_speed);
 	debug("%s: mii_speed %08x\n", __func__, readl(&eth->mii_speed));
 }
 
@@ -1097,6 +1109,7 @@ int fecmxc_initialize_multi(bd_t *bd, int dev_id, int phy_id, uint32_t addr)
 #ifdef CONFIG_PHYLIB
 	phydev = phy_find_by_mask(bus, 1 << phy_id, PHY_INTERFACE_MODE_RGMII);
 	if (!phydev) {
+		mdio_unregister(bus);
 		free(bus);
 		return -ENOMEM;
 	}
@@ -1108,6 +1121,7 @@ int fecmxc_initialize_multi(bd_t *bd, int dev_id, int phy_id, uint32_t addr)
 #ifdef CONFIG_PHYLIB
 		free(phydev);
 #endif
+		mdio_unregister(bus);
 		free(bus);
 	}
 	return ret;

drivers/serial/serial_mxc.c

@@ -75,6 +75,7 @@
 #define  UCR4_DREN	 (1<<0)  /* Recv data ready interrupt enable */
 #define  UFCR_RXTL_SHF   0       /* Receiver trigger level shift */
 #define  UFCR_RFDIV      (7<<7)  /* Reference freq divider mask */
+#define  UFCR_RFDIV_SHF  7      /* Reference freq divider shift */
 #define  UFCR_TXTL_SHF   10      /* Transmitter trigger level shift */
 #define  USR1_PARITYERR  (1<<15) /* Parity error interrupt flag */
 #define  USR1_RTSS	 (1<<14) /* RTS pin status */
@@ -135,6 +136,10 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
+#define TXTL  2 /* reset default */
+#define RXTL  1 /* reset default */
+#define RFDIV 4 /* divide input clock by 2 */
+
 static void mxc_serial_setbrg(void)
 {
 	u32 clk = imx_get_uartclk();
@@ -142,7 +147,9 @@ static void mxc_serial_setbrg(void)
 	if (!gd->baudrate)
 		gd->baudrate = CONFIG_BAUDRATE;
 
-	__REG(UART_PHYS + UFCR) = 4 << 7; /* divide input clock by 2 */
+	__REG(UART_PHYS + UFCR) = (RFDIV << UFCR_RFDIV_SHF)
+		| (TXTL << UFCR_TXTL_SHF)
+		| (RXTL << UFCR_RXTL_SHF);
 	__REG(UART_PHYS + UBIR) = 0xf;
 	__REG(UART_PHYS + UBMR) = clk / (2 * gd->baudrate);