As in Linux with d78c0ced60 ("net: ravb: Make write access to CXR35 first
before accessing other EMAC register"), configure CXR31 and CXR35 correctly
on rzg2. MII mode does not work correctly unless those registers are
properly configured.
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This pull request delivers a broad set of improvements across the
SoCFPGA family, including Agilex5, Cyclone V, SoC64, and common code.
Key updates include refined boot flows, new driver enablement, handoff
tooling enhancements, and several stability fixes.
Highlights:
* Agilex5:
- Enable FAT-based environment storage
- MMC driver restores legacy clkmgr-based clock lookup
- Cleanup of MMC raw mode enablement logic
* Cyclone V:
- SPL FAT boot support and updated bootcmd sequence
- Disable SPL SPI to prevent contention with FAT-based boot
- New board handoff script and BSP generator tooling
- Optimized Makefile support for SoCFPGA handoff workflows* New drivers:
- Cadence xSPI driver with full protocol and command support
- SPL enablement for DW APB GPIO controller
* Networking:
- xgmac MDIO now supports Clause 45 read/write operations
* NAND / SoC64:
- Enable ONFI detection in Denali NAND controller for SoC64 devices
* DTS and board updates:
- Sync common SoCFPGA U-Boot DTS with kernel sources
- Fixes for FPGA2SDRAM configuration and SoCFPGA boot stall behavior
- Vining_FPGA migrated to the modern LED framework
- Device tree relocation no longer forced off for Vining FPGA
* Tooling:
- Introduces a new Python-based Cyclone V BSP generator
covering EMIF, IOCSR, HPS, XML parsing, rendering, and documentation
to simplify board enablement and handoff regeneration workflows
Overall, this series improves boot robustness, enhances xSPI and MDIO
capabilities, modernizes board support, and introduces new tooling to
streamline SoCFPGA handoff generation.
Pipelines test passing
https://source.denx.de/u-boot/custodians/u-boot-socfpga/-/pipelines/28569
Aquantia PHYs are being used w/o SPI flash in some routers recently.
Current firmware loader only attempts to load from FS on top of MMC,
limiting the use on many devices.
Removed the old firmware loader, migrate to generic script based firmware
loader to allow a wider range and runtime override of firmware source.
(e.g., MMC, USB, UBIFS).
Tested on Buffalo WXR18000BE10P with UBIFS.
Signed-off-by: Beiyan Yun <root@infi.wang>
Split `aquantia_upload_firmware` into `aquantia_upload_firmware`
and `aquantia_do_upload_firmware` to prepare for fwloader change.
Signed-off-by: Beiyan Yun <root@infi.wang>
These two PHY drivers have some overlap of supported PHYs. A longer term
effort is needed to both remove duplication and enhance support by
dealing with some issues that downstream vendor drivers address. For
now, make both of these depend on !COMPILE_TEST so that we can enable
"allyesconfig".
Signed-off-by: Tom Rini <trini@konsulko.com>
Bind MDIO controller on Ethernet Controller load. The Airoha AN7581 SoC
have an integrated Switch based on MT7531 (or more saying MT7988).
Attach it to the mdio node in the switch node to support scanning for
MDIO devices on the BUS with DM API.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add the driver for the Airoha EN8811H 2.5 Gigabit PHY. The PHY supports
100/1000/2500 Mbps with auto negotiation only.
The driver uses two firmware files, for which updated versions are added to
linux-firmware already.
Locating the AIROHA FW within the filesystem at the designated partition
and path will trigger its automatic loading and writing to the PHY via MDIO.
If need board specific loading override,
please override the en8811h_read_fw function on board or architecture level.
Based on the Linux upstream AIROHA EN8811H driver code(air_en8811h.c),
I have modified the relevant process to align with the U-Boot boot sequence.
and have validated this on Banana Pi BPI-R3 Mini.
Signed-off-by: Lucien.Jheng <lucienzx159@gmail.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
bcm54210e_config() configures the RGMII delays and then calls
bcm5461_config(). But the latter will do a PHY soft reset and thus
resets the delay settings again. Call bcm5461_config() first to fix it.
Fixes: cba79a1b2e ("net: phy: broadcom: add support for BCM54210E")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Rafał Miłecki <rafal@milecki.pl>
According to the TI DP83869HM datasheet Revision D (June 2025), section
7.6.1.41 STRAP_STS Register, the STRAP_OPMODE bitmask is bit [11:9].
Fix this.
In case the PHY is auto-detected via PHY ID registers, or not described
in DT, or, in case the PHY is described in DT but the optional DT property
"ti,op-mode" is not present, then the driver reads out the PHY functional
mode (RGMII, SGMII, ...) from hardware straps.
Currently, all upstream users of this PHY specify both DT compatible string
"ethernet-phy-id2000.a0f1" and ti,op-mode = <DP83869_RGMII_COPPER_ETHERNET>
property, therefore it seems no upstream users are affected by this bug.
The driver currently interprets bits [2:0] of STRAP_STS register as PHY
functional mode. Those bits are controlled by ANEG_DIS, ANEGSEL_0 straps
and an always-zero reserved bit. Systems that use RGMII-to-Copper functional
mode are unlikely to disable auto-negotiation via ANEG_DIS strap, or change
auto-negotiation behavior via ANEGSEL_0 strap. Therefore, even with this bug
in place, the STRAP_STS register content is likely going to be interpreted
by the driver as RGMII-to-Copper mode.
However, for a system with PHY functional mode strapping set to other mode
than RGMII-to-Copper, the driver is likely to misinterpret the strapping
as RGMII-to-Copper and misconfigure the PHY.
For example, on a system with SGMII-to-Copper strapping, the STRAP_STS
register reads as 0x0c20, but the PHY ends up being configured for
incompatible RGMII-to-Copper mode.
Fixes: f3e22eea81 ("net: phy: add TI DP83869HM ethernet driver")
Signed-off-by: Thanh Quan <thanh.quan.xn@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Use FIELD_GET()
The last parameter to device_bind_driver_to_node is optional.
Since the returned information is not used and overwritten by
uclass_get_device_by_ofnode just provide NULL as parameter.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Alexander Feilke <alexander.feilke@ew.tq-group.com>
When using DM_MDIO on SOC with more than one FEC and not sharing the MDIO
bus the name of the driver and the bus needs to be unique. Since name
used in device_bind_driver_to_node needs to be a static string, add the
string to the fec_priv struct and reuse fec_set_dev_name to generate the
name with the device sequence number.
Fixes: 3b8f99a3e7 ("net: fec: add support for DM_MDIO")
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Alexander Feilke <alexander.feilke@ew.tq-group.com>
If DM_ETH_PHY is used and the FEC instance owns the shared MDIO bus,
eth_phy_get_mdio_bus returns NULL. If DM_MDIO bus is used, the
mdio_register API is called from dm_mdio_post_probe. Therefore the
bus should must be queried by name in this case.
For DM_MDIO case fec_mii_setspeed has already being called in
dm_fec_mdio_probe(), so skip setting this again.
Fixes: 3b8f99a3e7 ("net: fec: add support for DM_MDIO")
Fixes: e75d08821574 ("net: fec-mxc: prevent crash if no MAC address is set")
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Alexander Feilke <alexander.feilke@ew.tq-group.com>
The code should only be executed if MDIO bus is not assigned.
Otherwise the already assigned / allocated bus will be overwritten.
Add condition check and simplify the code to make it more readable.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Alexander Feilke <alexander.feilke@ew.tq-group.com>
If DM_MDIO is used and the FEC device is removed the mdio API
must not be used to remove the bus structure. Store pointer the
the udevice for MDIO bus created by dm_fec_bind_mdio and use DM
functions to cleanup the device in fecmxc_remove.
Fixes: 3b8f99a3e7 ("net: fec: add support for DM_MDIO")
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Alexander Feilke <alexander.feilke@ew.tq-group.com>
When initializing the MDIO bus the MDC signal needs to be configured.
Otherwise the communication over the bus may fail. Add the call to
fec_mii_setspeed to the DM_MDIO probe handler.
Fixes: 3b8f99a3e7 ("net: fec: add support for DM_MDIO")
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Alexander Feilke <alexander.feilke@ew.tq-group.com>
If no MAC address can be found (either in ROM, device tree or env),
the post_probe of an ethernet device will fail and therefore
the device cannot be instantiated.
The DM_ETH_PHY (eth-phy-uclass) use case must not be mixed with
using CONFIG_FEC_MXC_MDIO_BASE.
This prevents following error for MAC not fused, no eth[1]addr
env is present and providing a random MAC is disabled:
Net:
Error: ethernet@5b040000 address not set.
Error: ethernet@5b040000 address not set.
FEC: can't find phy-handle
"Error" handler, esr 0xbf000002
elr: 000000008004e4b8 lr : 000000008004e4b4 (reloc)
elr: 00000000bfe984b8 lr : 00000000bfe984b4
x0 : 0000000000000000 x1 : 0000000000000020
x2 : 00000000bbe61e50 x3 : 00000000bbe6e1a0
x4 : 0000000000000020 x5 : 0000000000000020
x6 : 000000000000000a x7 : 0000000000000000
x8 : 0000000000000000 x9 : 0000000000000008
x10: 00000000ffffffd8 x11: 0000000000000006
x12: 000000000001869f x13: 0000000000002c50
x14: 0000000000000000 x15: 00000000ffffffff
x16: 0000000000000000 x17: 0000000000000000
x18: 00000000bbe61d98 x19: 00000000bbe4fa68
x20: 00000000bbe78c10 x21: 00000000bbe6e460
x22: 00000000bbe78c10 x23: 00000000bbe91780
x24: 00000000bbe6e510 x25: 00000000000001f8
x26: 00000000ffff8000 x27: 0000000000000000
x28: 0000000000000000 x29: 00000000bbe4fa10
Code: f900003f 9100a3a1 97ffff6e 35000100 (f94017a1)
Resetting CPU ...
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Feilke <alexander.feilke@ew.tq-group.com>
phy_config may fail - for instance in parsing device tree.
This should be handled correctly. So return errors from
phy_config to caller.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Feilke <alexander.feilke@ew.tq-group.com>
Currently, the bind callback of the driver namely am65_cpsw_nuss_bind()
registers all ethernet ports including the ones that have been disabled
in the device-tree. Since the ports that have been disabled are ought to
be ignored, fix the implementation to register only the enabled ports as
indicated by their 'status' in their respective device-tree node.
Fixes: 3943531a54 ("net: ti: am65-cpsw-nuss: Define bind method for CPSW driver")
Reported-by: Wadim Egorov <w.egorov@phytec.de>
Closes: https://patch.msgid.link/8b4ac072-125c-493b-b12a-f0a4e9d56e7e@phytec.de
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu> says:
This patch series adds basic support for the boards based on Airoha
EN7523/EN7529/EN7562 SoCs. Due to ATF restrictions these boards are
able to run 32-bit OS only.
This patch series adds support for the following hardware:
* console UART
* ethernet controller/switch
* spinand flash (in non-dma mode)
The following issues may be expected:
* Extra slow UBI attaching in U-Boot (up to 20 sec with fastmap enabled).
This is caused by the lack of DMA support in the U-Boot airoha-snfi driver.
* Linux airoha-snfi driver in some cases might damage you flash data
(see: https://lore.kernel.org/lkml/20251012121707.2296160-15-mikhail.kshevetskiy@iopsys.eu/)
* Latest linux kernel is recommended to properly support flashes
with more than one plane per lun
(see: https://lore.kernel.org/lkml/20251012121707.2296160-7-mikhail.kshevetskiy@iopsys.eu/)
* It's NOT recommended to use flashes working in continuous mode because
U-Boot airoha-snfi driver does not support such flashes properly.
The patches was tested on the board:
- SoC: Airoha EN7562
- RAM: 512 MB
- SPI NAND: 4 Gbit, made by Toshiba
- Linux boot: was NOT tested
The U-Boot was chain-loaded from the running U-Boot. Airoha ATF-2.3 does
not allow easily chain-loading of U-Boot from U-Boot, so a special FIT
image (mimic linux kernel) was created
1) Create u-boot.its file with the following contents:
=== cut here ===
/dts-v1/;
/ {
description = "ARM OpenWrt FIT (Flattened Image Tree)";
#address-cells = <1>;
images {
u-boot-ram {
description = "OpenWrt U-Boot RAM image";
data = /incbin/("u-boot.bin.lzma");
type = "kernel";
arch = "arm";
os = "linux";
compression = "lzma";
load = <0x81e00000>;
entry = <0x81e00000>;
hash@1 {
algo = "crc32";
};
hash@2 {
algo = "sha1";
};
};
fdt-1 {
description = "OpenWrt device tree blob";
data = /incbin/("dts/upstream/src/arm/airoha/en7523-evb.dtb");
type = "flat_dt";
arch = "arm";
compression = "none";
hash@1 {
algo = "crc32";
};
hash@2 {
algo = "sha1";
};
};
};
configurations {
default = "config-ram-uboot";
config-ram-uboot {
description = "OpenWrt RAM U-Boot";
kernel = "u-boot-ram";
fdt = "fdt-1";
};
};
};
==================
2) Create u-boot.itb image to chain-load new u-boot from the old one
lzma_alone e u-boot.bin u-boot.bin.lzma
mkimage -f u-boot.its u-boot.itb
3) Load new u-boot from the old one
U-Boot> tftpboot u-boot.itb && bootm
Link: https://lore.kernel.org/r/20251101004503.2379529-1-mikhail.kshevetskiy@iopsys.eu
This allow us remove some an7581/an7583 specific code and use a common
code instead.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Add support for the Renesas Ethernet Switch3 (RSW3) controller,
present in R-Car Gen5 SoCs such as R-Car X5H (R8A78000). The
hardware offset differences are handled via driver match data.
The driver newly detects whether the switch prot is connected
to xPCS or not, and if so, turns on MIOC bit 3. This is new on
R-Car X5H. GWCKSC register is also programmed only on X5H. The
rest of the operation is identical to RSwitch2.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
Signed-off-by: Thanh Quan <thanh.quan.xn@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
The MPIC_MDC_CLK clock setting value differs between R-Car S4
and R-Car X5H. Parametrize the value in preparation for R-Car
X5H addition into this driver. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The GWDCBAC0, GWDCBAC1, FWPBFCSDC, CABPIRM register offsets changed
between R-Car S4 and R-Car X5H. Parametrize their offsets in preparation
for R-Car X5H addition into this driver. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Inline FWRO, CARO, GWRO, TARO, RMRO macros directly into the
follow up register macros. FWRO, CARO, GWRO, TARO are already
zero, drop them. RMRO is 0x1000, increment all registers which
add RMRO by 0x1000 directly. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The forwarding engine CSD register offset changed between the
R-Car S4 and R-Car X5H. Parametrize this offset in preparation
for R-Car X5H addition into this driver. Clean up the macro
parameter names and make them more obvious. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The total port counts differ across variants of this IP in
R-Car S4 and R-Car X5H. Parametrize port count in preparation
for R-Car X5H addition into this driver. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The COMA, ETHA, GWCA offsets differ across variants of this IP in
R-Car S4 and R-Car X5H. Parametrize these offsets in preparation
for R-Car X5H addition into this driver. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This IP does support operating MII and SerDes via different ports.
Currently, the driver assumes that MII and SerDes are always bound
together on the same port, but this may not be the case. Implement
support for controlling MII and SerDes separately.
While the change is extensive, the gist of the change is to pass
pointer to the selected port registers to MII or SerDes functions,
depending on which port and operations should be done on that port.
Each combined ETHA instance contains both MII and SerDes register
pointers, which may not point to the same port, and passes those
registers to MII and SerDes functions respectively to control the
MII or SerDes of each port.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The new version of RSwitch3 in Renesas R-Car Gen5 uses multiple
clock to supply the IP. Convert the driver to bulk clock API to
cater for both single clock of R-Car S4 and multiple clock of
R-Car Gen5. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Empty RX DMA descriptor must contain .die_dt field set to DT_FEMPTY,
because hardware DMA overwrites this field to non-DT_FEMPTY when data
are received, and the .recv callback tests the content of RX descriptor
.die_dt field to determine whether hardware did receive any data and
updated the .die_dt field, and based on that information, receives a
packet or not. Fix the incorrect RX DMA descriptor initialization to
assure the .recv callback always works correctly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Fix indent from multiple spaces to tabs, to be consistent with
coding style and the rest of the driver. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add support for the optional 'phy-supply' property in the ENETC MDIO
driver. This allows the driver to enable and manage the PHY's power
supply via the regulator framework when specified in device tree.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
A device-tree property is already defined to indicate that the internal
PHY should be used with active-low leds, which corresponds to a
specific bit in the dedicated syscon register.
Add support for setting this bit when the property is present.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
We know about all the relevant fields in the syscon register so there
is no reason to read it first and modify it.
Build the register from scratch instead, with all relevant fields set.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
The Synchronous Abort and reset errors occurred due
to incorrect parameter passing during initialization.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
[jf: add missing #if IS_ENABLED(CONFIG_BITBANGMII)]
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
With commit 597fe041a8 ("net/phy: enable get_phy_id redefinable") we
made get_phy_id a public but weak function, so that PHY drivers that had
required non-standard ways of getting the PHY ID could be supported.
However, overloading a weak function multiple times is (rightly) a link
error. At this point, we have two PHYs which make use of this feature,
so make both of them only available when COMPILE_TEST is unset, as part
of being able to support "allyesconfig" in the future.
Signed-off-by: Tom Rini <trini@konsulko.com>
Synchronize paged PHY helpers with Linux v6.17.
Add support for PHY devices that use paged register access by
implementing the following functions:
- phy_save_page(): Save current page number
- phy_select_page(): Switch to a specific page and return previous page
- phy_restore_page(): Restore previously saved page
Also adds read_page and write_page callbacks to the phy_driver
structure to enable driver-specific page handling.
These helpers allow safe access to paged PHY registers by ensuring
proper page selection and restoration,
even in error conditions, which will be used by the Airoha PHY driver.
Signed-off-by: Lucien.Jheng <lucienzx159@gmail.com>
The commit 997786bbf4 ("drivers/net/airoha_eth: fix stalling in package
receiving") can be improved. Instead of returning previous descriptor
it's possible:
* do nothing in even descriptor case
* return 2 descriptor to the queue (current and previous) in the odd
descriptor case.
This patch:
* implements above approach
* remove logic not required within new approach
* adds note that PKTBUFSRX must be even and larger than 7
for reliable driver operations
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
In preparation for support of MDIO on AN7581, move the MT7531 MMIO logic
to a dedicated driver and permit usage of the mdio read/write function
to the mtk_eth driver.
This only affect MT7988 that can use MMIO operation to access the Switch
register. The MT7988 code is updated to make use of the external driver.
This permits Airoha driver to make use of DM_MDIO to bind for the MT7531
driver that have the same exact register.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Correctly free the MDIO Bus on calling cleanup function. While at it
also fix a copy-paste error and rename the cleanup function name to the
more specific name.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
On exiting the phy_setting function for MT7988, the PHY page is never
restored to Page 0. This can cause all kind of problem with reading the
status of the PHY at runtime.
Correctly restore PHY page on exiting the PHY setting function.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The PHY for MT7531/MT7988 are never actully turned ON/OFF for the
affected PHY as we are read/writing to the wrong PHY address.
This is caused by the fact that we use the MT753X_PHY_ADDR macro 2
times offsetting the address multiple times.
One in the _setup() function and one in the mt7531_mii_read/write.
Drop the additional usage of MT753X_PHY_ADDR in setup() to correctly
set the PHY.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
