When the host ECC fails to correct the data error of NAND device,
there's a special read for data recovery method which can be setup
by the host for the next read. There are several retry levels that
can be attempted until the lost data is recovered or definitely
assumed lost.
This is the port of linux commit
f2cb43c98010 (mtd: spinand: Add read retry support)
Signed-off-by: Cheng Ming Lin <chengminglin@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu> # U-Boot port
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
The code was ported from linux-6.12. The original continuous reading
support was implemented by Miquel Raynal <miquel.raynal@bootlin.com>
in linux commit 631cfdd0520d (mtd: spi-nand: Add continuous read support).
Here is an original patch description:
--------------------------------------
A regular page read consist in:
- Asking one page of content from the NAND array to be loaded in the
chip's SRAM,
- Waiting for the operation to be done,
- Retrieving the data (I/O phase) from the chip's SRAM.
When reading several sequential pages, the above operation is repeated
over and over. There is however a way to optimize these accesses, by
enabling continuous reads. The feature requires the NAND chip to have a
second internal SRAM area plus a bit of additional internal logic to
trigger another internal transfer between the NAND array and the second
SRAM area while the I/O phase is ongoing. Once the first I/O phase is
done, the host can continue reading more data, continuously, as the chip
will automatically switch to the second SRAM content (which has already
been loaded) and in turns trigger the next load into the first SRAM area
again.
From an instruction perspective, the command op-codes are different, but
the same cycles are required. The only difference is that after a
continuous read (which is stopped by a CS deassert), the host must
observe a delay of tRST. However, because there is no guarantee in Linux
regarding the actual state of the CS pin after a transfer (in order to
speed-up the next transfer if targeting the same device), it was
necessary to manually end the continuous read with a configuration
register write operation.
Continuous reads have two main drawbacks:
* They only work on full pages (column address ignored)
* Only the main data area is pulled, out-of-band bytes are not
accessible. Said otherwise, the feature can only be useful with on-die
ECC engines.
Performance wise, measures have been performed on a Zynq platform using
Macronix SPI-NAND controller with a Macronix chip (based on the
flash_speed tool modified for testing sequential reads):
- 1-1-1 mode: performances improved from +3% (2-pages) up to +10% after
a dozen pages.
- 1-1-4 mode: performances improved from +15% (2-pages) up to +40% after
a dozen pages.
This series is based on a previous work from Macronix engineer Jaime
Liao.
--------------------------------------
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
SkyHigh spinand device has ECC enable bit in configuration register but
it must be always enabled. If ECC is disabled, read and write ops
results in undetermined state. For such devices, a way to avoid raw
access is needed.
Introduce SPINAND_NO_RAW_ACCESS flag to advertise the device does not
support raw access. In such devices, the on-die ECC engine ops returns
error to I/O request in raw mode.
Checking and marking BBM need to be cared as special case, by adding
fallback mechanism that tries read/write OOB with ECC enabled.
This is a port of linux commit
6d9d6ab3a82a (mtd: spinand: Introduce a way to avoid raw access)
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu> # U-Boot port
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Add two flags for inserting the Plane Select bit into the column
address during the write_to_cache and the read_from_cache operation.
Add the SPINAND_HAS_PROG_PLANE_SELECT_BIT flag for serial NAND flash
that require inserting the Plane Select bit into the column address
during the write_to_cache operation.
Add the SPINAND_HAS_READ_PLANE_SELECT_BIT flag for serial NAND flash
that require inserting the Plane Select bit into the column address
during the read_from_cache operation.
This is a port of linux commit
ca229bdbef29 (mtd: spinand: Add support for setting plane select bits)
Signed-off-by: Cheng Ming Lin <chengminglin@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240909092643.2434479-2-linchengming884@gmail.com
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu> # U-Boot port
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
This makes the U-Boot SPI NAND driver almost the same as in Linux 6.10.
The only major difference is support of ECC engines. The Linux driver
supports different ECC engines while U-Boot uses on-die ECC only.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
This aligns spinand_wait() with the linux kernel. Instead of calling into
spi_mem_poll_status() which is not implemented in U-Boot, we code the
polling logic and make sure that schedule() is called periodically.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Make use of the spi-mem direct mapping API to let advanced controllers
optimize read/write operations when they support direct mapping.
Based on a linux commit 981d1aa0697c ("mtd: spinand: Use the spi-mem dirmap API")
created by Boris Brezillon <bbrezillon@kernel.org> with additional
fixes taken from Linux 6.10.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Add omap common environment variables to .env. We retain the old-style C
environment .h files to maintain compatibility with other omap devices that
have not moved to using .env yet.
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
The RK806 PMIC has a bitfield for configuring the restart/reset behavior
(which I assume Rockchip calls "function") whenever the PMIC is reset
either programmatically (c.f. DEV_RST in the datasheet) or via PWRCTRL
or RESETB pins.
For RK806, the following values are possible for RST_FUN:
0b00 means "Restart PMU"
0b01 means "Reset all the power off reset registers, forcing
the state to switch to ACTIVE mode"
0b10 means "Reset all the power off reset registers, forcing
the state to switch to ACTIVE mode, and simultaneously
pull down the RESETB PIN for 5mS before releasing"
0b11 means the same as for 0b10 just above.
This adds the appropriate logic in the driver to parse the new
rockchip,reset-mode DT property to pass this information. It just
happens that the values in the binding match the values to write in the
bitfield so no mapping is necessary.
For backward compatibility reasons, if the property is missing we set it
to 0b10 (i.e. BIT(7)) like before this commit was merged instead of
leaving it untouched like in the kernel driver.
Note that this does nothing useful for U-Boot at the moment as the ways
to reset the device (e.g. via `reset` command) doesn't interact with the
RK8xx PMIC and simply does a CPU reset.
Considering the upstream Linux kernel left this register untouched until
(assumed) v6.17[1], this is useful for cases in which the U-Boot
bootloader has this patch (and running with a DT with
rockchip,reset-mode property set) and running an upstream kernel before
(assumed) v6.17, or alternatively later without the property in the
kernel DT.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git/commit/?id=87b48d86b77686013f5c2a8866ed299312b671db
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Because the early malloc pool size is set to 0x18000, so using this
start address may cause conflict with ATF, then corrupt the heap data.
So we delete the definition to use the default early malloc pool from
CONFIG_SPL_STACK to avoid any conflict
Signed-off-by: Ye Li <ye.li@nxp.com>
Cherry picked from nxp-imx/uboot-imx commit
1ba675df122627a19debe1d807877052705372c6
Jérémie Dautheribes: applied the same patch to the frdm and qsb
imx93-based boards
Signed-off-by: Jérémie Dautheribes <jeremie.dautheribes@bootlin.com>
The legacy network stack sets net_try_count to 1 at the beginning of the
net_loop() function. This is required for net_start_again() to work
properly. Therefore, set the variable accordingly in the do_ping()
function when NET_LWIP=y. This fixes an issue where a ping to an
unreachable destination would run twice on the same network device. For
example with qemu_arm64_lwip_defconfig:
=> dhcp
DHCP client bound to address 10.0.2.15 (3 ms)
=> ping 10.0.0.1
Using virtio-net#32 device
ping failed; host 10.0.0.1 is not alive
Using virtio-net#32 device
ping failed; host 10.0.0.1 is not alive
=> QEMU: Terminated
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Introduce the DNS Kconfig symbol so that various network commands may
use host names without the dns command (CMD_DNS) being selected.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
CC: E Shattow <e@freeshell.de>
The header of LiMon imported files reference a License file which
does not exist in U-Boot. Some files were forgotten when adding the
SPDX-License-Identifier.
The LiMon files were originally licensed under GPLv2 as can be seen in
commit [2ea91039].
Based on this commit, add the correct SPDX license identifier.
While at it drop the reference to the non-existing License file from all
LiMon files and update the SPDX-License-Identifier to SPDX version 3.
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
Introduce Voyager board specific code, including
- dram info
- shared cache enabling
Signed-off-by: Randolph Sheng-Kai Lin <randolph@andestech.com>
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This driver adds support for the single mailbox channel of the MSS
system controller on the Microchip PolarFire SoC.
Signed-off-by: Jamie Gibbons <jamie.gibbons@microchip.com>
Acked-by: Leo Yu-Chi Liang <ycliang@andestech.com>
SPL checks for a magic word in the system manager's scratch
register to determine if an L2 reset has occurred. If detected,
SPL places all slave CPUs (CPU1–3) into WFI mode. The master
CPU (CPU0) then initiates a warm reset by writing to the RMR_EL3
system register and also enters WFI mode.
This warm reset flow is handled entirely within the HPS. The
function `socfpga_sysreset_request()` triggers the warm
reset, and upon SPL re-entry, the updated `lowlevel_init_soc64.S`
handles the necessary initialization.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Put all slave CPUs (CPU1-3) into WFI mode. Master CPU (CPU0) writes
the magic word into system manager's scratch register to indicate
the system has performed L2 reset and request reset manager to
perform hardware handshake and then trigger L2 reset. CPU0 put
itself into WFI mode. L2 reset will reboot all HPS CPU cores after
which all HPS cores are in WFI mode. L2 reset is followed by warm
reset request by SPL via RMR_EL3 system register.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Add i3c command file to support select, get i3c device
target list, read and write operation.
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@altera.com>
Fix the I3C device with spike filter unable to detect issue by setting
tHIGH_INIT to 200ns for first broadcast address.
This is according to MIPI SPEC 1.1.1 for first broadcast address
which is already part of linux upstreamed patch.
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@altera.com>
Enable i3c general uclass driver. This uclass driver will have
genaral read and write api to call the specific i3c driver.
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@altera.com>
Enable driver for Synopsis MIPI DWI3C for the family
device agilex5. This driver is migrated from linux version 6.6.37 LTS
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@altera.com>
Smatch reports a warning about possibly needing parens around the macro
PSEUDO_HDR_SIZE. This will not affect the one place the macro is used
but add the parens anyway as it is good practice to have them and if the
macro is used again in the future it could possibly matter then.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Jerome Forissier <jerome.forissier@linaro.org>
CI: https://source.denx.de/u-boot/custodians/u-boot-stm/-/pipelines/27236
- Add support for STM32 TIMERS and STM32 PWM on STM32MP25
- Add STM32MP13xx SPL and OpTee-OS start support
- Fix header misuse in stm32 reset drivers
- Fix STMicroelectronics spelling
- Fix clk-stm32h7 wrong macros used in register read
- Fix PRE_CON_BUF_ADDR on STM32MP13
- Fix clock identifier passed to struct scmi_clk_parent_set_in
- Fix stm32 reset for STM32F4/F7 and H7
- Enable OF_UPSTREAM_BUILD_VENDOR for stm32mp13_defconfig
- Add STM32MP23 SoC and stm32mp235f-dk board support
This pull request includes updates for the SoCFPGA platform intended for the 2025.10 release
cycle. The highlights focus on enabling the Power Manager for Agilex5, NAND boot support
enhancements, and various bug fixes and cleanups across SoCFPGA components.
CI:
* https://source.denx.de/u-boot/custodians/u-boot-socfpga/-/pipelines/27221
Summary of changes:
Agilex5 Power Manager:
* Initial driver support and DT bindings are added for the Agilex5 Power Manager, enabling
better power domain control.
NAND Boot Support for Agilex5:
* SPL support for NAND boot is enabled.
* UBI/UBIFS support is configured in defconfigs.
* Memory layout updates (malloc and BSS relocation) ensure proper boot behavior.
Code Quality Improvements:
* Coverity and runtime bug fixes (e.g., jtag_usercode check, sub-device conditionals).
* Several cleanup patches addressing formatting, logic, and initialization issues.
General Maintenance:
* SPDX license tags and header include fixes.
* Device tree updates to limit SPI clock frequency and other minor adjustments.
These contributions come from Alif Zakuan Yuslaimi, Andrew Goodbody, Dinesh Maniyam, Naresh
Kumar Ravulapalli, and Tingting Meng.
This patch set has been tested on Agilex 5 devkit.
Add the required configuration in the U-Boot env to enable Linux NAND
boot with UBI / UBIFS.
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
The watchdog could have been already started by a previous boot
stage (e.g. bootrom or secure OS). U-Boot has to start and kick
the watchdog even when CONFIG_WATCHDOG_AUTOSTART is not enabled
or when the DT property u-boot,noautostart is present.
Add the helper wdt_set_force_autostart() that can be called by the
driver's probe() when it detects that the watchdog has already
been started and is running.
Co-developed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Second set of u-boot-at91 features for the 2025.10 cycle:
This feature set includes the addition of new sama7d65 SoC and a new
board named sama7d65-curiosity.
Enable bootstd.
Update defconfigs to the latest u-boot requirements.
Enable SYS_THUMB_BUILD and LTO and to reduce binary size.
Enable NET_RANDOM_ETHADDR.
Disable JFFS2 support.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add the basic Kconfig options, addresses and other values for the
existing Kconfig settings for the new Allwinner A523/T527/H728 SoC.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The X-Powers AXP323 is very close sibling to the AXP313A, only that it
adds support for dual-phasing the first two DC/DC converters.
We do not really care about this particular feature, so just add the new
compatible string and tie it to the existing AXP313A support code.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The generic name 'EFI' would be more useful for common EFI features. At
present it just refers to the EFI app and stub, which is confusing.
Rename it to EFI_CLIENT
Signed-off-by: Simon Glass <sjg@chromium.org>
