The init_r parsing of U-Boot device tree to search the binman
information errors. set CONFIG_BINMAN_FDT to no to fix this.
Fixes: 7079eeb72f ("imx: imxrt1050-evk: Add support for SPI flash booting
s")
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Deduplicate defconfigs for all DH i.MX6 DHSOM by including common
configs/imx_dhsom_defconfig . This does introduce changes to the
board configuration, namely it enables commands used on all DHSOM
devices consistenty, the prompt is changed to u-boot=>, support for
booting non-Linux OS which was likely never used is disabled, GPT
partition table support is enabled, generic MTD support is enabled,
LED support is enabled, DM PHY, PMIC and regulator support is also
enabled, KASLR command is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Deduplicate defconfigs for all DH i.MX8MP DHSOM by factoring out the
common parts into generic _dhsom_defconfig and including those using
the #include <configs/...> preprocessor macro, which is applicable to
defconfigs as well. This enables CMD_EXPORTENV on all iMX8MP DHSOM
systems to be consistent with other DHSOM systems.
Signed-off-by: Marek Vasut <marex@denx.de>
Neither the DRC02 nor PicoITX carrier board contains the PCA954x I2C mux
chip, the chip is only present on PDK3 carrier board. Disable support for
the PCA954x mux chip and I2C mux altogether on both i.MX8MP DHCOM DRC02 and
PicoITX.
Signed-off-by: Marek Vasut <marex@denx.de>
Make sure DM regulator support is enabled on this board, just like on all
the other DH i.MX8MP DHCOM SoM based boards.
Signed-off-by: Marek Vasut <marex@denx.de>
Provide a way to access this data structure so that the meminfo command
can use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
U-Boot has a fairly rigid memory map which is normally not visible
unless debugging is enabled in board_f.c
Update the 'meminfo' command to show it. This command does not cover
arch-specific pieces but gives a good overview of where things are.
Signed-off-by: Simon Glass <sjg@chromium.org>
In preparation for expanding this command, move it into a separate file.
Rename the function to remove the extra underscore. Update the number of
arguments to 1, since 3 is incorrect.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The bootstage array includes pointers to strings but not the strings
themselves. The strings are added when stashing, but including them in
the size calculation gives an inflated view of the amount of space used
by the array.
Update this function so it can return the amount of memory used by the
bootstage structures themselves, without the strings which they point
to.
Signed-off-by: Simon Glass <sjg@chromium.org>
The call to malloc() is a bit strange. The naming of the arguments
suggests that an address is passed, but in fact it is a pointer, at
least in the board_init_r() function and SPL equivalent.
Update it to work as described. Add a function comment as well.
Note that this does adjustment does not extend into the malloc()
implementation itself, apart from changing mem_malloc_init(), since
there are lots of casts and pointers and integers are used
interchangeably.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
CI: https://source.denx.de/u-boot/custodians/u-boot-dfu/-/pipelines/22962
Dfu:
- Rely on device tree for spi speed/mode on spi flash
Android Image:
- Fix booting on platforms having > 4GiB of memory
- Decompress boot image to kernel_addr_r when compression is enabled
- Honor CONFIG_SYS_LOAD_ADDR when mkbootimg uses default address
Bcb:
- Rework bcb command to use U_BOOT_LONGHELP
- Move ab_select cmd to bcb cmd
- Implement ab_dump command in bcb
- bcb: Write '_<slot>' instead of '<slot>' to misc partition
The Hardkernel ODROID-M1S is a single-board computer based on Rockchip
RK3566 SoC. It features e.g. 4/8 GB LPDDR4 RAM, 64 GB eMMC, SD-card,
GbE LAN, HDMI 2.0, M.2 NVMe and USB 2.0/3.0.
Features tested on a ODROID-M1S 8GB rev1.0 20230906:
- SD-card boot
- eMMC boot
- Ethernet
- PCIe/NVMe
- USB gadget
- USB host
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Hardkernel ODROID-M1S is a single-board computer based on Rockchip
RK3566 SoC. It features e.g. 4/8 GB LPDDR4 RAM, 64 GB eMMC, SD-card,
GbE LAN, HDMI 2.0, M.2 NVMe and USB 2.0/3.0.
Add initial support for eMMC, SD-card, Ethernet, HDMI, PCIe and USB.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20240827211825.1419820-5-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: 10dc64fe0f980c47c7e747885ddf7a8c12780337 ]
(cherry picked from commit f811548e758b52896f725753086c42b49dc42c0d)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The vendor prefix for Hardkernel ODROID-M1 is incorrectly listed as
rockchip. Use the proper hardkernel vendor prefix for this board, while
at it also drop the redundant soc prefix.
Fixes: fd3583267703 ("arm64: dts: rockchip: Add Hardkernel ODROID-M1 board")
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20240827211825.1419820-3-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: 735065e774dcfc62e38df01a535862138b6c92ed ]
(cherry picked from commit e7259a2c4a6f2ebdfc96b8bbffc77fe67604b11f)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
After the full convertion of usb gadget interrupt handling to
usb_gadget_generic_ops, it is now possible to use DM_USB_GADGET,
DWC2_OTG and DWC3_GENERIC together without causing a build error.
Change to use USB_DWC3_GENERIC instead of USB_XHCI_DWC3 to complte the
migration initiated in commit 1bc4e8eb1d ("rockchip: Migrate to use
DM_USB_GADGET on RK3328"). No functional change is intended.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Hardkernel ODROID-M2 is a single-board computer based on Rockchip
RK3588S2 SoC. It features e.g. 8/16 GB LPDDR5 RAM, 64 GB eMMC, SD-card,
GbE LAN, HDMI 2.0, M.2 NVMe and USB 2.0/3.0/Type-C.
Features tested on a ODROID-M2 16GB rev1.0 20240611:
- SD-card boot
- eMMC boot
- Ethernet
- PCIe/NVMe
- USB gadget
- USB host
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Hardkernel ODROID-M2 is a single-board computer based on Rockchip
RK3588S2 SoC. It features e.g. 8/16 GB LPDDR5 RAM, 64 GB eMMC, SD-card,
GbE LAN, HDMI 2.0, M.2 NVMe and USB 2.0/3.0/Type-C.
Add initial support for eMMC, SD-card, Ethernet, PCIe and USB.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20240901112020.3224704-3-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: ce48b8c976ce439c336def6e06bf8224a8ff9125 ]
(cherry picked from commit 7ba62d8b4cb010c6fcb7077550b46d5f5fb5af6d)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove config options for ARM SCMI. It is not required to boot the
board and when using the most recent mainline A-TF it actually causes
the device to freeze during boot due to missing SCMI support.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Some of the Powkiddy devices switched to using a different vendor for
the vdd_cpu regulator. Unfortunately the device does not have a new
revision to denote this, so users have no way of knowing in advance.
Add code to detect if a device is present at addresses 0x1c or 0x40 on
the i2c0 bus and update the devicetree if needed.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Refactor the board detection logic (again) to make it compatible with
the upstream device-trees, and switch to OF_UPSTREAM.
Now the device boots with the device-tree for the 353P, and then
loads the correct device tree (of 10) in the later stages of SPL.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add dedicated getter and setter for SCLK_UART0_PMU.
This allows the driver to correctly handle UART0 clocks, and thus
it fixes the issues with UART0 not working in case DEBUG_UART is
disabled.
Unlike other Rockchip SoCs, i.e. rk3399, in the PX30 the default
clock source for UART is GPLL, instead of external oscillator.
If the DEBUG_UART is enabled, the clock source is changed in
board_debug_uart_init function to 24Mhz oscillator, which also
matches the fallback value obtained from DT node.
In case the DEBUG_UART is disabled, the UART clock source remains
default, and the DM serial driver wrongly configures the baud rate,
resulting in broken communication.
By implementing the UART clock getter/setter, the serial driver
can probe the actual configuration and corectly configure itself.
The DEBUG_UART settings now should not affect it.
The driver supports GPLL and 24M oscillator. NPLL and USBPHY480M
sources, that are managed by CRU, are not yet handled, as likely
they won't be used in real scenarios.
Signed-off-by: Lukasz Czechowski <lukasz.czechowski@thaumatec.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Basically, Radxa's boards are intended to turn LEDs on at U-Boot.
add `default-state = "on"` to u-boot.dtsi.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Basically, Radxa's boards are intended to turn LEDs on at U-Boot.
enable gpio-leds driver and led command.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
ROCK Pi 4 series and ROCK 4C+ cannot share .dtsi file because 4C+ is
different board.
add rk3399-rock-pi-4-u-boot.dtsi contents and remove dependency of it.
no functional change is intended.
Fixes: 71a95e2efd ("arm: dts: rockchip: add Radxa ROCK 4C+")
Suggested-by: Dragan Simic <dsimic@manjaro.org>
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Fix the issue introduced by commit fed064477c2c
("arm64: zynqmp: Print an error for split to lock mode switch").
The mini u-boot is hanging, because of the tcm is not initialized.
The mini u-boot is using the tcm to reserve the mmu table and
currently it is not initialized, so allowing u-boot to initialize
the tcm.
Signed-off-by: Padmarao Begari <padmarao.begari@amd.com>
Link: https://lore.kernel.org/r/20241011113435.1966604-1-padmarao.begari@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
As per bootmenu support added default boot options to CC on AMD CCs and
default to SOM on others.
However, if no secondary boot device is enabled in the design,it should
be the default boot option for SOM when combined with AMD CCs because it
only contains SOM peripherals.
To address this issue, The conditional check for the bootmenu_default
variable was removed, and it has always been set to SOM as the default
boot option.
In this way, users can choose preferred boot options from the bootmenu
based on the boot devices configured in the design for AMD CCs.
Fixes: 61bf0fa866 ("xilinx: zynqmp: Add bootmenu support")
Signed-off-by: John Vicky Vykuntapu <johnvicky.vykuntapu@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/0e30b44ce3b478fdec21edad8d896f4d438ce331.1727867715.git.michal.simek@amd.com
Fix the issue introduced by commit 067e029480
("board: xilinx: Remove conditional check for Microblaze").
The scriptaddr should be physical location not really offset
from start of DDR. When U-Boot is not found boot.scr script
address in device tree, then it is assigned based on script
address and ram base address for Microblaze and i.e exceeding
DDR memory. To fix this, the script address is assigned
initially with offset instead of address. Later it is added
with ram base address and gets the physical address.
Signed-off-by: Padmarao Begari <padmarao.begari@amd.com>
Link: https://lore.kernel.org/r/20241001082537.830286-1-padmarao.begari@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The RPU pytest introduced by commit e894c10c04
("test/py: zynqmp_rpu: Add test for loading RPU apps") expects
3rd parameter as string not a number that's why extend command
to actually handle both. The issue with existing code is that
when any non number string is passed hextoul returns 0. For
backward compatibility zynqmp tcminit 0/1 can be still used but
it is recommended to use strings instead.
Signed-off-by: Padmarao Begari <padmarao.begari@amd.com>
Link: https://lore.kernel.org/r/20240930043814.530181-3-padmarao.begari@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The zynqmp tcminit crashes the U-Boot when switching from
r5-mode "split" to "lockstep" instead it should throw an error.
When cpu is enabled, the check_tcm_mode() function checks
if the previous mode is "split", switch mode is "lockstep" then
it returns the error code and the initialize_tcm() function is not
updating the global control register of the RPU instead it prints
the error message. When cpu is disabled, the check_tcm_mode()
function returns the success code for switch split to lockstep mode.
Signed-off-by: Padmarao Begari <padmarao.begari@amd.com>
Link: https://lore.kernel.org/r/20240930043814.530181-2-padmarao.begari@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
I enabled IMX_HAB on an imx8mp board, but even though I knew about the
implementation, I forgot that I had to provide a sane value for
SPL_LOAD_FIT_ADDRESS. The help text for IMX_HAB doesn't mention this
implicit requirement, and there's no build-time warning; the default
0x0 value just ends up being returned from
board_spl_fit_buffer_addr(), obviously resulting in a non-booting
board.
The existing imx8m* board configs that set a non-zero value currently
all use 0x44000000. The actual value doesn't matter too much, but 0 is
always wrong for imx8m platforms. So just use 0x44000000 as default
for those platforms.
Signed-off-by: Rasmus Villemoes <ravi@prevas.dk>
Convert to using livetree API functions.
Without this if livetree is enabled (OF_LIVE) the fsl_esdhc_imx
driver will fail to read vendor-specific properties from the dt.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Convert to using livetree API functions.
Without this if livetree is enabled (OF_LIVE) the mxc-i2c
driver will fail to support scl-gpios and sda-gpios for
i2c bus recovery.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Convert to using livetree API functions.
Without this if livetree is enabled (OF_LIVE) the imx8m-power-domain
driver will (silently) fail to probe its children leaving you with
no power domain support causing issues with certain devices.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
