A UFS device needs its bRefClkFreq attribute set to the correct value
before switching to high speed. If bRefClkFreq is set to the wrong
value, all transactions after the power mode change will fail.
The bRefClkFreq depends on the host controller and the device.
Query the device's current bRefClkFreq and compare with the ref_clk
specified in the device-tree. If the two differ, set the bRefClkFreq
to the device-tree's ref_clk frequency.
Taken from Linux kernel v6.17 (drivers/ufs/core/ufshcd.c and
include/ufs/ufs.h) and ported to U-Boot.
Signed-off-by: Jared McArthur <j-mcarthur@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Link: https://patch.msgid.link/20251010195556.1772611-3-j-mcarthur@ti.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Commit d232d7fdbf ("ufs: core: sync ufshci.h with Linux v6.12") updated
the Data Direction values from bitmask values to simple enumerations.
Before:
enum {
UTP_NO_DATA_TRANSFER = 0x00000000,
UTP_HOST_TO_DEVICE = 0x02000000,
UTP_DEVICE_TO_HOST = 0x04000000,
};
Updated:
enum utp_data_direction {
UTP_NO_DATA_TRANSFER = 0,
UTP_HOST_TO_DEVICE = 1,
UTP_DEVICE_TO_HOST = 2,
};
However, the U-Boot code still uses these values directly without shifting,
and resulting in wrong bitfield placement in the Transfer Request
Descriptor.
This fixes the issue by applying the necessary shift to align the value.
Fixes: d232d7fdbf ("ufs: core: sync ufshci.h with Linux v6.12")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20251010024557.673787-1-hayashi.kunihiko@socionext.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
In ti_j721e_ufs_probe there is a call to clk_get_rate but the code after
that attempts to detect an error from that call incorrectly uses
IS_ERR_VALUE. Instead the test should just be for regular error codes.
The call returns an unsigned long so that needs to be cast to a signed type
first of all.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Anshul Dalal <anshuld@ti.com>
Link: https://patch.msgid.link/20251007-ufs_ti-v2-1-501f575b6947@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
In versaclock_probe vc5->pin_xin may be an error pointer so need to
check with IS_ERR before attempting to dereference it.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In versaclock_get_name -ENOMEM is passed to ERR_PTR but nothing is
done with the value that this calculates which is obviously not the
intention of the code. This is confirmed by the code around where this
function is called.
Instead return the value from ERR_PTR.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
You cannot test an unsigned member of a struct for being negative, the
test will always fail. Instead assign the return value of
fdtdec_get_int, which returns an int, to a temporary variable declared
as an int, so that it can be tested for being negative before being
assigned to the unsigned struct member.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
epnum is used as an index into an array. The limit check for this index
should be performed before using it to access an element in the array to
prevent possible bounds overrun.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
A null check for the variable 'data' was introduced before dereferencing
it for set_phy_power but other uses were not so protected. Add the null
check for other dereferences of 'data'.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
The variable node is assigned to the return value of a function that
returns an int. It is tested for being negative and then passed as an
argument to a function that takes an int. So 'node' should not be
declared as unsigned. Correct it.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Combining two bits into a mask to be used so that the same write code
can be used to set or reset bits in a register clearly needs to use the
binary 'or' operator, not the binary 'and'. Fix it.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
When a variable needs a null check before it is dreferenced ensure that
this is done even in the case of assignment on declaration. This was not
happening for lurb_priv so correct it.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
fsl_fdt_fixup_usb_erratum uses strcmp to detect an error but then
returns 'err' without it being set to an error. Calling code may not
detect that an error occurred leading to a silent failure. Instead just
return -EINVAL.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
THe variable node is assigned to the return value of a function that
returns an int. It is tested for being negative and then passed as an
argument to a function that takes an int. So 'node' should not be
declared as unsigned. Correct it.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut@mailbox.org>
Add initial board docs for Milk-V Mars CM (eMMC) and Milk-V Mars CM Lite
(SD Card) to the visionfive2 board target.
Signed-off-by: E Shattow <e@freeshell.de>
Add Milk-V Mars CM and Mars CM Lite to visionfive2.
These boards were previously supported and then removed in the transition
to OF_UPSTREAM. The dts have landed in the for-next queue so let's add the
boards again.
Signed-off-by: E Shattow <e@freeshell.de>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Add identifier for Milk-V Mars CM to dts selection callback in SPL, and
to fdtfile environment variable default value selection in payload.
Signed-off-by: E Shattow <e@freeshell.de>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Prune overrides of upstream jh7110.dtsi now that the required nodes are
available through the devicetree-rebasing subtree.
Signed-off-by: E Shattow <e@freeshell.de>
Milk-V Mars CM Lite is a System-on-Module based on the Milk-V Mars CM
without the onboard eMMC storage component populated and configured
instead for SD3.0 Card Slot on that interface via 100-pin connector.
Link to Milk-V Mars CM Lite schematics: https://github.com/milkv-mars/mars-files/tree/main/Mars-CM_Hardware_Schematices
Link to StarFive JH7110 Technical Reference Manual: https://doc-en.rvspace.org/JH7110/TRM/index.html
Link to Raspberry Pi CM4IO datasheet: https://datasheets.raspberrypi.com/cm4io/cm4io-datasheet.pdf
Add the devicetree file to make use of StarFive JH7110 common supported
features PMIC, EEPROM, UART, I2C, GPIO, PCIe, QSPI Flash, PWM, and
Ethernet. Also configure the eMMC interface mmc0 for SD Card use and
configure the common SD Card interface mmc1 for onboard SDIO BT+WiFi.
Signed-off-by: E Shattow <e@freeshell.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
[ upstream commit: 4cce8b2503ab50f75a2dbc3eef2e55722836588e ]
(cherry picked from commit c7821d537e5a61e5d543588674b71fb43ec0665b)
Milk-V Mars CM is a System-on-Module based on the StarFive VisionFive 2
board and Radxa CM3 System-on-Module compatible with the Raspberry Pi
CM4IO Classic IO Board.
Mars CM SoM features:
- StarFive JH7110 System on Chip with RV64GC up to 1.5GHz
- AXP15060 Power Management Unit
- LPDDR4 2GB / 4GB / 8GB DRAM memory
- BL24C04F 4K bits (512 x 8) EEPROM
- GigaDevice 25LQ128EWIG QSPI NOR Flash 16M or SoC ROM UART loader for
boot (selectable by GPIO)
- eMMC5.0 8GB / 16GB / 32GB flash storage onboard
- AP6256 via SDIO 2.0 onboard wireless connectivity WiFi 5 + Bluetooth
5.2 (optional, present in models with WiFi feature)
- 1x Motorcomm YT8531C Gigabit Ethernet PHY
- IMG BXE-4-32 Integrated GPU with 3D Acceleration:
- H.264 & H.265 4K@60fps Decoding
- H.265 1080p@30fps Encoding
- JPEG encoder / decoder
Additional features available via 2x 100-pin connectors for CM4IO Board:
- 1x HDMI 2.0
- 1x MIPI DSI (4-lanes)
- 1x 2CH Audio out (via GPIO)
- 1x MIPI CSI (2x2-lanes or 1x4-lanes)
- 1x USB 2.0
- 1x PCIe 1-lane Host, Gen 2 (5Gbps)
- Up to 28x GPIO, supporting 3.3V
- UART x6
- PWM x8
- I2C x7
- SPI
- I2S
Link to Milk-V Mars CM schematics: https://github.com/milkv-mars/mars-files/tree/main/Mars-CM_Hardware_Schematices
Link to StarFive JH7110 Technical Reference Manual: https://doc-en.rvspace.org/JH7110/TRM/index.html
Link to Raspberry Pi CM4IO datasheet: https://datasheets.raspberrypi.com/cm4io/cm4io-datasheet.pdf
Add the devicetree file to make use of StarFive JH7110 common supported
features PMIC, EEPROM, UART, I2C, GPIO, eMMC, PCIe, QSPI Flash, PWM, and
Ethernet. Also configure the common SD Card interface mmc1 for onboard
SDIO BT+WiFi.
Signed-off-by: E Shattow <e@freeshell.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
[ upstream commit: 8d193bc0aa2e802be30de331317639482735d738 ]
(cherry picked from commit 8e935d097e975e6322b63fdc8ef9894c8582bef0)
Add a common board dtsi for use by Milk-V Mars CM and Milk-V Mars CM Lite.
Signed-off-by: E Shattow <e@freeshell.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
[ upstream commit: 651b30c58775e334c79aa3ecd44a3d98ac201db2 ]
(cherry picked from commit 034af14dcd1e6dbfa4f41a340b6d92b054604858)
Relax no-sdio restriction on mmc1 for jh7110 boards. Property was
introduced for StarFive VisionFive2 dts to configure mmc1 for SD Card
but this is not necessary, the restriction is only needed to block use of
commands that would cause a device to malfunction.
Signed-off-by: E Shattow <e@freeshell.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
[ upstream commit: 481ee0fcbb9a0f0706d6d29de9570d1048aff631 ]
(cherry picked from commit b4e73596622f791e3c2a2449022671e4e579fbd0)
The current sifive_clint driver can fully support GHRTv2 clint.
Add the compatible of GHRTv2 clint, sifive,clint2, to sifive_clint_ids
list.
Signed-off-by: Vincent Chen <vincent.chen@sifive.com>
Signed-off-by: Wayling Chen <wayling.chen@sifive.com>
Signed-off-by: Max Hsu <max.hsu@sifive.com>
Signed-off-by: Jimmy Ho <jimmy.ho@sifive.com>
No big features this time, mostly a collection of patches that have been
lying around for a bit. There are some DT updates, for those SoCs that
do not use OF_UPSTREAM yet, hopefully that's the last time we need to do
this exercise. And that's offset by switching over two more SoCs to
OF_UPSTREAM. Two new boards get a defconfig, and some improvements for
the sun8i-emac Ethernet driver. Finally a patch that fixes occassional
DRAM size misdetection for new A523 boards.
There are a few outstanding patches that just wait for getting some
details confirmed, which I might send then later.
CI passed, and I tested this briefly on affected boards.
Sync the kernel devicetree source files for the Allwinner SoCs with
32-bit cores that do not use OF_UPSTREAM yet. The files were taken
from a v6.18-rc1 tree.
To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 994e5818392c and 9fdef3c3d8c2.
This commit also adds a new board devicetree for the A33 Vstar board,
plus one DT overlay for the OrangePi Zero interface board.
This update should not impact any existing U-Boot functionality.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Sync the devicetree files from the official Linux kernel tree, v6.18-rc1.
This is covering Allwinner SoCs with 64-bit ARM cores.
The bulk is cosmetic changes: board model name changes, DT node renames,
whitespace fixes.
The actual changes are not dramatic: the CPU cores get their caches
described properly, some A64 video clocks get fixed, some A64 boards
describe the header pins for the WiFi module, the Pinephone adds an
alternative magnetometer used on some board revisions.
On the H5 side the microSD slots get marked as having no write-protect
detection, and the NanoPi Neo Plus2 board describes its regulators better.
The H6 boards switch from RSB to I2C for their PMIC connection.
As before, this omits the non-backwards compatible changes to the R_INTC
controller, to remain compatible with older kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
In contrast to some other Allwinner SoCs, there is no difference between
the DTs for the Allwinner A80 SoCs (sun9i) between the U-Boot and the
Linux kernel repository.
Remove the old copies of the A80 related .dts and .dtsi files, and switch
most of sun9i boards over to use OF_UPSTREAM.
There is the Sunchip CX-A99 (family of) board(s) for which we don't have
a DT in the kernel tree. Keep the .dts file in the legacy U-Boot DT
directory, and let the board's defconfig opt out of OF_UPSTREAM.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
In contrast to some other Allwinner SoCs, there is no difference between
the DTs for the Allwinner T113-s3 SoC (sun20i) between the U-Boot and the
Linux kernel repository.
Remove the old copies of the T113-s3 related .dts and .dtsi files, and
switch the whole SoC (represented by just one board) over to use
OF_UPSTREAM.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
A device-tree property is already defined to indicate that the internal
PHY should be used with active-low leds, which corresponds to a
specific bit in the dedicated syscon register.
Add support for setting this bit when the property is present.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
We know about all the relevant fields in the syscon register so there
is no reason to read it first and modify it.
Build the register from scratch instead, with all relevant fields set.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
NetCube Systems Kumquat is a board based on the Allwinner V3s SoC,
including:
- 64MB DDR2 included in SoC
- 10/100 Mbps Ethernet
- USB-C DRD
- Audio Codec
- Isolated CAN-FD
- ESP32 over SDIO
- 8MB SPI-NOR Flash for bootloader
- I2C EEPROM for MAC addresses
- SDIO Connector for eMMC or SD-Card
- 8x 12/24V IOs, 4x normally open relays
- DS3232 RTC with Battery Backup
- QWIIC connectors for external I2C devices
Signed-off-by: Lukas Schmid <lukas.schmid@netcube.li>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently we pass this for u-boot-spl.kwb targets, however when
building sunxi-spl.bin in the TOC0 format we may also need to
specify a KEYDIR, as such we should also pass this when set
to mkimage for the sunxi-spl.bin target.
Signed-off-by: James Hilliard <james.hilliard1@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
The H6 and H616 DRAM initialisation code recently gained a joint and
improved size detection routine, which helped to avoid the occasional
DRAM size misdetection.
Use the same code for the A523 DRAM initialisation as well, which
suffers from the same misdetection at times.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Chen-Yu Tsai <wens@kernel.org>
The OrangePi 4A is a typical Raspberry Pi model B sized development
board from Xunlong designed around an Allwinner T527 SoC.
The board has the following features:
- Allwinner T527 SoC
- AXP717B + AXP323 PMICs
- Up to 4GB LPDDR4 DRAM
- micro SD slot
- optional eMMC module
- M.2 slot for PCIe 2.0 x1
- 16 MB SPI-NOR flash
- 4x USB 2.0 type-A ports (one can be used in gadget mode)
- 1x Gigabit ethernet w/ Motorcomm PHY (through yet to be supported GMAC200)
- 3.5mm audio jack via internal audio codec
- HDMI 2.0 output
- eDP, MIPI CSI (2-lane and 4-lane) and MIPI DSI (4-lane) connectors
- USB type-C port purely for power
- AP6256 (Broadcom BCM4345) WiFi 5.0 + BT 5.0
- unsoldered headers for ADC and an additional USB 2.0 host port
- 40-pin GPIO header
Add defconfig for it.
Signed-off-by: Chen-Yu Tsai <wens@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Pull request efi-2026-01-rc1-2
CI:
* https://source.denx.de/u-boot/custodians/u-boot-efi/-/pipelines/28024
Documentation:
* develop: virtio: Fix qemu example (true/false -> on/off)
* separate read and write command documentation
* usage: Add general rule for `$?`
* askenv: Reword and remove return value
* seama: Reword return value section
* usage: Use glob for all commands
* Fix typos and formatting
UEFI:
* console: support editable input fields
For clarity, add a reference link to the start of the section on command
documentation that all commands follow some general rules.
Signed-off-by: Tom Rini <trini@konsulko.com>
