Previously, dynamic frequency scaling supported rates only through fixed
divison.
This virtual clock mux configuration enables more varied rates on A72
clock ID 202 by setting up the required register.
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Signed-off-by: Reid Tonking <reidt@ti.com>
In order for the Cortex-A72s to operate at different frequencies other
than the default 2GHz, add in a new 'virtual' mux (a mux that does not
physically exist in the clock tree) that can be selected.
CC: Vishal Mahaveer <vishalm@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Signed-off-by: Reid Tonking <reidt@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
This adds support for the MT8365 EVK board with the following
features enabled/tested: Boot, UART, Watchdog and MMC.
Signed-off-by: Julien Masson <jmasson@baylibre.com>
This adds the pinctrl bindings for Mediatek MT8365 SoC based on the
dt-bindings in Linux tag v6.7-rc2.
(commit 8b4c397d88d97d4fd9c3f3527aa66688b1a3387a)
Signed-off-by: Julien Masson <jmasson@baylibre.com>
This patch adds basic support for MediaTek MT8365 SoC.
The dtsi has been copied from Linux source code tag v6.7-rc2.
(commit 9b5d64654ea8f51fe1e8e29ca1777b620be8fb7c)
Signed-off-by: Julien Masson <jmasson@baylibre.com>
This patch adds clock driver support for MediaTek MT8365 SoC.
The changes are based on the Linux source code tag v6.7-rc2.
clk-mt8365.c has been written based on these kernel files:
- clk-mt8365.c (a96cbb146a9736f501fe66ebda6a9018735e5e8a)
- clk-mt8365-apmixedsys.c (65c9ad77cbc0eed78db94d80041aba675cfbdfa9)
And adapted following the clk attributes supported by U-Boot.
Signed-off-by: Julien Masson <jmasson@baylibre.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
This adds the clock bindings for Mediatek MT8365 SoC based on the
dt-bindings in Linux tag v6.7-rc2.
(commit c61978175ac1337f028ac1f956666f16db84f4e5)
Signed-off-by: Julien Masson <jmasson@baylibre.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
spl_mmc_emmc_boot_partition return a number different from 0
if the partition is a boot one. We can have the uboot img
for instance in a raw offset in emmc partition 0 so we would
like to continue to load the next stage. If the user want
to use EMMC as boot device allow him to use any part of the
emmc and not only boot partition
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
The block count limit on MMC based devices should be set according to
CONFIG_SYS_MMC_MAX_BLK_COUNT instead of hardcoding value.
Signed-off-by: Julien Masson <jmasson@baylibre.com>
Change optee driver service enumeration to not enumerate (and
allocate a zero sized shared memory buffer) when OP-TEE
reports that there is no service to enumerate.
This change fixes an existing issue that occurs when the such zero
sized shared memory buffer allocated from malloc() has a physical
address of offset 0 of a physical 4kB page. In such case, OP-TEE
secure world refuses to register the zero-sized shared memory
area and makes U-Boot optee service enumeration to fail.
Fixes: 94ccfb78a4 ("drivers: tee: optee: discover OP-TEE services")
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Change optee probe function to only warn when service enumeration
sequence fails instead of reporting an optee driver probe failure.
Indeed U-Boot can still use OP-TEE even if some OP-TEE services are
not discovered.
Fixes: 94ccfb78a4 ("drivers: tee: optee: discover OP-TEE services")
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
DSP core is going into abnormal state when load callback is called
after starting of DSP core.
Reload of firmware needs core to be stopped first, followed by
load.
So avoid loading of firmware, when core is started.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
The AEM and Juno FVPs (Fixed Virtual Platforms) support a VirtIO
disc interface. Adding VIRTIO to the list of boot devices allows
these FastModel platforms to boot from 'disc' in the same way
the hardware counterpart can boot from SATA or USB.
This is a NOP if CONFIG_CMD_VIRTIO is not enabled, so no impact
on Juno hardware (which is built with vexpress_aemv8a_juno_defconfig)
Signed-off-by: Robert Catherall <robert.catherall@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Currently the wget command is hard wired to HTTP port 80. This is
inconvenient, as it is extremely easy to start trivial HTTP server
as an unprivileged user using e.g. python http module to serve the
files, but such a server has to run on one of the higher ports:
"
$ python3 -m http.server -d $(pwd) 8080
"
Make it possible to configure HTTP server port the same way it is
possible to configure TFTP server port, using environment variable
'httpdstp' (similar to 'tftpdstp'). Retain port 80 as the default
fallback port. This way, users can start their own trivial server
and conveniently download whatever files they need into U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The current DDR subsystem configuration occasionally results in write failures,
impacting memory stability, on Verdin AM62 Solo 512MB WB IT 0072 SKU.
This commit addresses the issue by adjusting Drive Pull-Up/Down and
Write Latency to improve the eye diagram and ensure reliable write operations.
This configuration is shared with all Verdin AM62 SoM and
it does not introduce regressions.
Configurations changes from previous / default values:
- Drive Pull-Up/Down from 40 to 34.3 Ohm
- Write Latency from 8 to 10
- ODTLon / ODTLoff latency from 0 / 0 to 4 / 20 nCK
- VREF control range 1 at 27 %
- tFAW from 30 to 40 ns
Configuration is output from SysConfig [1] web tool, currently at version
1.18.1+3343 (DDR SubSystem v9.10).
[1] https://dev.ti.com/sysconfig
Fixes: 7d1a10659f ("board: toradex: add verdin am62 support")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The contents of README.sha1 only refer to process around verification
of the pcs440ep board firmware in flash. The device was removed in
commit 242836a893 ("powerpc: ppc4xx: remove pcs440ep support") in
2015 so this readme isn't really relevant anymore so can be removed.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Turn display connector power off on boot and reboot to prevent any
bogus start up sequence of any panel potentially attached to the
display connector.
Signed-off-by: Marek Vasut <marex@denx.de>
Migrate to the new environment format and drop most of the config.h.
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add timer driver in Starfive SoC. It is an timer that outside
of CPU core and inside Starfive SoC.
Signed-off-by: Kuan Lim Lee <kuanlim.lee@starfivetech.com>
Signed-off-by: Wei Liang Lim <weiliang.lim@starfivetech.com>
Changes for v2:
- correct driver name, comment, variable
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
MicroBlaze V is new AMD/Xilinx soft-core 32bit RISC-V processor IP.
It is hardware compatible with classic MicroBlaze processor.
The patch contains initial wiring and configuration for initial HW design
with memory, cpu, interrupt controller, timers and uartlite console
(interrupt controller is listed but U-Boot is not using it).
Provided DT is just describing one configuration and should be taken only
as example.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Add gpio-restart node to do reset.
Before applied this patch, System Reset Extension doesn't appear with
sbi command.
OpenSBI 1.3
Machine:
Vendor ID 489
Architecture ID 8000000000000007
Implementation ID 4210427
Extensions:
sbi_set_timer
sbi_console_putchar
...[snip]...
IPI Extension
RFENCE Extension
Hart State Management Extension
Performance Monitoring Unit Extension
After applied this patch, System Reset Extension is supported from SBI.
OpenSBI 1.3
Machine:
Vendor ID 489
Architecture ID 8000000000000007
Implementation ID 4210427
Extensions:
sbi_set_timer
sbi_console_putchar
...[snip]...
IPI Extension
RFENCE Extension
Hart State Management Extension
System Reset Extension
Performance Monitoring Unit Extension
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Pull request for efi-next-20231217
Documentation:
* replace MD5 and SHA1 by SHA256 in examples
UEFI:
* Refactor boot manager and bootefi command to let the EFI boot method work
without shell.
Both SHA1 and (especially) MD5 are no longer as safe as they once were for
cryptographic use. Replaces examples which use them with examples using
SHA256 instead. This will provide more-secure defaults for users who use
documentation examples as a base for their own use. This is not too
necessary for non-verified-boot scenarios (since someone could just replace
the checksum), but I wanted to be complete.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now that efi_loader subsystem provides interfaces that are equivalent
with bootefi command, we can replace command invocations with APIs.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Now it is clear that the command actually depends on interfaces,
not "bootefi bootmgr" command.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
In the prior commits, interfaces for executing EFI binary and boot manager
were carved out. Move them under efi_loader directory so that they can
be called from other places without depending on bootefi command.
Only efi_selftest-related code will be left in bootefi.c.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Device paths allocated in bootefi_test_prepare() will be immediately
consumed by do_efi_selftest() and there is no need to keep them for later
use. Introduce test-specific varialbles to make it easier to move other
bootmgr functions into library directory in the next commit.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Carve binary execution code out of do_bootefi_image() in order to move
binary-execution specific code into library directory in the later
commit.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Carve EFI boot manager related code out of do_bootefi_image() in order
to move boot manager specific code into library directory in the later
commit.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Replicate some code and re-organize do_bootefi() into three cases, which
will be carved out as independent functions in the next two commits.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Unfold do_bootefi_image() into do_bootefi() in order to make it easier
to re-organize do_bootefi() in the next commit.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Import DRAM timings generated by the DDR tool 3.31 which introduce assorted
tweaks to the DRAM controller settings. Furthermore, enable DBI to improve
noise resilience of the DRAM bus by reducing the number of bit changes on
the bus.
Reduce the DRAM rate to 3600 MTps to remove all remaining correctable errors
reported by EDAC . It is not entirely clear why the slightly faster setting
does produce sporadic correctable errors, while this one does not, but this
could be related to simpler PLL setting at 3600 MTps.
Enable inline ECC which is necessary to detect ECC errors and collect
statistics by the EDAC driver in Linux. This reduces the DRAM size by
64 MiB for each 512 MiB of DRAM, so for a 4 GiB device the available
DRAM size becomes 3.5 GiB and for 2 GiB device the available DRAM size
becomes 1.8 GiB.
Signed-off-by: Marek Vasut <marex@denx.de>
In case the Buck5 and Buck6 regulators which supply DRAM Vdd1 and Vdd2/Vddq
respectively operate in automatic PWM/PFM mode, the DRAM EDAC detects more
correctable errors than if the regulators operate in forced PWM only mode.
Force DRAM regulators to forced PWM mode only to stop tempting the DRAM.
Signed-off-by: Marek Vasut <marex@denx.de>
After talking with the author off-list I was reminded that this part of
the series was not supposed to be merged, only parts 1-3 upon further
review.
This reverts commit 58a277c207.
Signed-off-by: Tom Rini <trini@konsulko.com>
clock patches for u-boot/next
The main thing in here is Igor's conversion of soc_clk_dump to a clk_ops
member. There's also a write-protect feature for nuvoton clocks.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
clock changes for u-boot/master
This has some clock fixes which should go in before the release. It's a bit
late in the cycle, but most of these have tests to go along with them.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
The base address of extended DDR does not change across the K3 family.
Setting this per SoC is not needed. Remove this definition to help
remove the last bits from K3 include/configs/*.h files.
Signed-off-by: Andrew Davis <afd@ti.com>
