"fastboot flash" tries to malloc 8 MiB buffer after receiving data over
USB and trying to write it to eMMC. Right now only 8.12 MiB malloc is
available for E850-96 overall, which leads to this issue:
Malloc failed for: CHUNK_TYPE_RAW
Fix it by increasing malloc pool size from 8.12 MiB up to 32 MiB, like
it's done in many other boards using fastboot.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add 'dfu_alt_info' environment variable which contains:
- Linux eMMC partitions ('esp' and 'rootfs')
- eMMC Boot Partition A layout, where all the firmware reside
It makes it possible to update the bootloader (U-Boot). All sizes in
'dfu_alt_info' are given in 512B blocks (LBA). eMMC size is 58.2 GiB.
The eMMC Boot Partition A (mmc0boot0) layout looks like this:
boot0 partition (4 MiB)
0x0 +----------------------------------+
| fwbl1 (12 KiB) |
0x18 +----------------------------------+
| epbl (76 KiB) |
0xb0 +----------------------------------+
| bl2 (256 KiB) |
0x2b0 +----------------------------------+
| dram_train (16 KiB) |
0x2d0 +----------------------------------+
| ect_test (50 KiB) |
0x334 +----------------------------------+
| acpm_test (130 KiB) |
0x438 +----------------------------------+
| bootloader (2 MiB) |
0x1438 +----------------------------------+
| el3_mon (256 KiB) |
0x1638 +----------------------------------+
where U-Boot should be flashed into 'bootloader' partition. So U-Boot
binary size should be 2 MiB or less. The whole boot0 partition is 4 MiB,
but only 2.8 MiB is currently used.
With this change, the U-Boot binary can be updated on eMMC like this:
=> dfu 0 mmc 0
$ dfu-util -D u-boot.bin -a bootloader
Looking at E850-96 booting diagram at [1,2], it's easy to see how these
binaries are being executed in the same order they are placed in
mmc0boot0 area. E.g. fwbl1 is definitely BL1 (software part of Boot
ROM). So it's obvious the ROM code just reads the binary from eMMC at
0x0 offset into RAM (SRAM?) and executes it.
All mentioned images can be found at [3], as stated in E850-96 U-Boot
documentation. 'dram_train', 'ect_test' and 'acpm_test' areas should be
ignored -- they are not flashed with real images.
[1] doc/board/samsung/e850-96.rst
[2] https://docs.u-boot.org/en/latest/board/samsung/e850-96.html
[3] https://gitlab.com/Linaro/96boards/e850-96/images/-/tree/master/images
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Setup "serial#" environment variable from the chip ID. The chip ID is
read from Exynos850 SoC OTP (One Time Programmable) memory, which acts
like an EEPROM and contains unique SoC ID. This "serial#" variable is
further used for "fastboot devices" serial number, etc.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The only thing needed from DWC3 glue layer for Exynos850 is to enable
USB clocks. The generic glue layer driver already does that. Add
Exynos850 dwc3 compatible string to enable support for this chip.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add DM driver for Exynos USB PHY controllers. For now it only supports
Exynos850 SoC. Only UTMI+ (USB 2.0) PHY interface is implemented, as
Exynos850 doesn't support USB 3.0. Only two clocks are used for this
controller:
- phy: bus clock, used for PHY registers access
- ref: PHY reference clock (OSCCLK)
Ported from Linux kernel: drivers/phy/samsung/phy-exynos5-usbdrd.c
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/27149
- Add support for the NXP imx93 frdm board.
- imx93_evk and phycore-imx93 cleanups.
- Convert imx6dl-sielaff to OF_UPSTREAM and fix serial download mode boot.
- Fix crash in imx power-domain.
- Migrate Phytec imx8mm boards to standard boot.
- Fix smatch warnings.
The load address for the R5's SPL is defined in Kconfig by
SPL_TEXT_BASE. Rather than hard coding the load address which could
lead to hard to debug issues if this value is changed, just use the
SPL_TEXT_BASE value.
Reviewed-by: Andrew Davis <afd@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
The uart11 reg address was a copy of the value for uart10.
Update it to the correct value.
Signed-off-by: Rebecca Cran <rebecca@os.amperecomputing.com>
Smatch reported a possible buffer overflow in exfat_set_label but it
turns out that this code is unused so just guard the function with
'#ifndef __UBOOT__' as well as exfat_get_label that is also unused and
the helper static find_label.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Instead of strcpy which is unbounded use strlcpy to ensure that the
receiving buffer cannot be overflowed.
This issue found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Commit 86acdce2ba ("common: add config for board_init() call")
introduced CONFIG_BOARD_INIT option. This option can be disabled for the
boards where board_init() function is not needed. Remove empty
board_init() calls for all boards where it's possible, and disable
CONFIG_BOARD_INIT in all related defconfigs.
This cleanup was made semi-automatically using these scripts: [1].
No functional change, but the binary size for the modified boards is
reduced a bit.
[1] https://github.com/joe-skb7/uboot-convert-scripts/tree/master/remove-board-init
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm_beacon
Tested-by: Bryan Brattlof <bb@ti.com>
Acked-by: Peng Fan <peng.fan@nxp.com> #NXP boards
Trigger all tests of PBIST and LBIST using appropriate calls to set the
core under test (MAIN R5 2_0) to it's required state.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Add a driver for the BIST module that support triggering of both PBIST
(Memory BIST) and LBIST (Logic BIST) tests. Also expose the relevant
operations and functions that would be required for an end user to
trigger the tests.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
uclass_find_next_device always returns 0, so instead make it a void and
update calling sites.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
AMD/Xilinx/FPGA changes for v2025.10-rc1 v2
zynqmp:
- Generate fit-dtb.blob all the time
- Simplify power-domain driver bind
zynqmp_mini:
- Remove PSCI_RESET
fpga:
- Improve user feedback in case of FPGA bitstream load failure
misc:
- Fix kernel-doc in gpio zynq and axi_mrmac
spi:
- Revert fix in STIG mode
[trini: Remove CONFIG_FPGA_VERSALPL=y from sandbox due to
sandbox+clang+asan test problem]
Signed-off-by: Tom Rini <trini@konsulko.com>
The 'overhead' variable is uninitialized and actually shall not be used.
Delete it to fix coverity CID 37041718 - Uninitialized scalar variable.
Fixes: 73c40fcb73 ("spl: Refactor spl_load_info->read to use units of bytes")
Reported-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Goodbody <andrew.goodbody@linaro.org>
There is no PMIC and USB related C code in this file.
Remove these unneeded header files.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
There is nothing in this file that makes use of the definitions from
sizes.h and stringify.h.
Remove them.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Local variable ret is declared as unsigned but is used to receive the
return value of functions that return int. ret is then tested for being
negative which must always fail. Change ret to be an int.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
remove boot logic from shared env file for phyboard-polis and
phygate-tauri.
Adjust configs for both boards as well.
Space at the beginning of addressable RAM is reserved for space used via
standard boot env variables. CONFIG_SYS_LOAD_ADDR is set to the lowest
address behind the standard boot variables reserved space.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
In case of the i.MX8M power-domains (i.MX8MQ, MM, MN) there is only
one power-domain for each device. Therefore the 'id' field in struct
power_domain should always be zero.
Currently if a power-domain is accessed after the initial bind, the
'id' field is left uninitialized. This didn't cause any problems
until the following commits were introduced:
9086b64ca0 ("power-domain: Add support for refcounting (again)")
a785ef2448 ("imx: power-domain: Enable refcounting on imx8mp")
Now the 'id' field gets accessed in the power_domain_off() sequence
and the invalid value causes "Synchronous Abort" failures.
This was observed on a i.MX8MM board when running "usb start" and
then "usb stop".
Fix this issue by setting power_domain->id to '0' in
imx8m_power_domain_of_xlate().
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Fixes: d08a194871 ("imx: add support for i.MX8MQ power domain controller")
Fixes: 9086b64ca0 ("power-domain: Add support for refcounting (again)")
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
We need to set CONFIG_SDP_LOADADDR to a reasonable value in order
to successfully load the U-Boot proper image in SPL via SDP.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Drop unused define for PCA9450 PMIC register which is already part of
the header file <power/pca9450.h> since commit 1d0d257043 ("imx93_evk:
spl: update pmic settings").
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
The kernel-doc comment for the axi_mrmac_recv function was missing
the colon (':') after the '@packetp' parameter tag.
The kernel-doc comment for the axi_mrmac_free_pkt function was missing
the colon (':') after the 'length' parameter tag.
This caused a Sparse warnings regarding the 'packetp' and 'length'
parameters not being described. Fix the formatting to align
with kernel-doc standards and resolve the warning.
drivers/net/xilinx_axi_mrmac.c:357:
warning: Function parameter or member 'packetp' not described
in 'axi_mrmac_recv'
drivers/net/xilinx_axi_mrmac.c:411:
warning: Function parameter or member 'length' not described
in 'axi_mrmac_free_pkt'
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20250717044855.1359443-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The 'dev' parameter in the zynq_gpio_get_bank_pin function was not
described in its kernel-doc comment block, leading to a Sparse warning.
drivers/gpio/zynq_gpio.c:194: warning: Function parameter or member 'dev'
not described in 'zynq_gpio_get_bank_pin'
Add a description for the 'dev' parameter to satisfy the documentation
requirements and improve code clarity for this function.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20250717044632.1353588-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
As reported by clang 20.1, fix multiple of the following:
drivers/fpga/ivm_core.c:593:23: error: a function declaration without
a prototype is deprecated in all versions of C
[-Werror,-Wstrict-prototypes]
593 | long int ispVMDataSize()
| ^
| void
Also fix the following warning from checkpatch.pl:
WARNING: Prefer 'long' over 'long int' as the int is unnecessary
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Link: https://lore.kernel.org/r/20250708152455.1214487-6-vtpieter@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
In cmd/fpga.c, change some `debug` calls to `log_err` for important
user feedback and use CMD_RET_FAILURE in favor of CMD_RET_USAGE due to
its long output which hides the actual, useful return message. Change
the remaining `debug` calls to `log_debug`. Remove all 'fpga:' and
__func__ strings as log_* has this covered.
For `do_fpga_loads`, move up the `do_fpga_check_params` call for more
consistent command output; use a constant instead of multiple '5' use.
In drivers/fpga/zynq*.c, change 'up to' to 'above' which corrects this
confusing/wrong statement.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Link: https://lore.kernel.org/r/20250708152455.1214487-2-vtpieter@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
This is a fix for the sporadic mmc write failure:
mmc write failed
0 blocks written: ERROR
After this happens the emmc will remain in an error state
where subsequent read/writes fail with a timeout.
The mmc driver sends CMD25 - WRITE_MULTIPLE_BLOCK which
can sporadically timeout. When this happens, the mmc driver
aborts the transfer and returns the above error messages.
But the emmc still remains in data transfer mode, since
the timeout was decided by uboot, not by the emmc.
Fix this by sending the STOP_TRANSMISSION command (CMD12)
and waiting for the emmc to be in ready state again (CMD13).
Transferring data blocks after a CMD25 can take anywhere
between 5 and +15s on Samsung EMMCs and the current timeout
is not enough. Increase the timeout by 2x to accommodate the
long transfer times observed.
Signed-off-by: Iulian Banaga <iulianeugen.banaga@mobileye.com>
Acked-by: Jimmy Durand Wesolowski <jimmy.wesolowski@mobileye.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The exynos5420 DTSes in linux kernel uses the compatibles
samsung,exynos5420-dw-mshc{,-smu} instead of just
samsung,exynos-dwmmc. Match the additional compatibles in the driver
to make it possible to use it with DTSes from Linux kernel.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
[ grimler: rebase after clksel reg abstraction and re-write commit message ]
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
the Exynos4210 devices in u-boot uses samsung,exynos4412-sdhci as
sdhci compatible in their DTSes, while the upstream DTSes uses
samsung,exynos4210-sdhci.
Add samsung,exynos4210-sdhci compatible string for s5p_sdhci driver as
well so that it can be used with upstream DTSes.
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The common sdhci infrastructure is already parsing the cd-gpios
property, since commit 451931ea70 ("mmc: sdhci: Read cd-gpio from
devicetree"). The s5p code is therefore duplicated, and also broken
since it assumes that the GPIO value is inverted, while the sdhci code
correctly follows the ACTIVE_LOW/ACTIVE_HIGH flag specified in the
device tree.
This fix was originally authored by Simon Shields:
https://github.com/fourkbomb/u-boot/commit/2eac9dea7903
The change has been tested on exynos4210-i9100, a device similar to
exynos4210-trats.
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In [0], Andrew noted a code quality issue in the implementation of
blk_find_first and blk_find_next. This led to the observation that the
logic of these functions was also likely incorrect, and based on a quick
check it seemed the functions were unused outside of test code, which
did not exercise the potential failure case, so we felt they should be
removed. In [1], a test patch which illustrates the failure in sandbox
is provided for reference.
Because a more thorough check agrees that these functions are unused,
they are currently incorrect, and fixed/removable flags on block devices
prior to probe are unreliable, just remove these functions instead of
fixing them. All potential users should have used blk_first_device_err
instead anyway.
CI results at [2].
[0] https://patchwork.ozlabs.org/project/uboot/patch/20250714-blk-uclass-v1-1-d21428c5f762@linaro.org/
[1] https://gist.github.com/gmalysa/b05e73a5c14bc18c5741a0e0e06a2992
[2] https://gitlab.com/gmalysa/lnxdsp-u-boot/-/pipelines/1931210857
Signed-off-by: Greg Malysa <malysagreg@gmail.com>
Reviewed-by: Andrew Goodbody <andrew.goodbody@linaro.org>
SYSRESET_PSCI should select SPL_ARM_PSCI_FW only when SPL_SYSRESET is
enabled/required. This change saves 1.6kB on Xilinx ZynqMP Kria platform.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The buffer for a name to be copied into must also contain the
terminating 0 byte but strlen returns the length of the string without
counting that 0 byte. Adjust the length checks to take this into
account.
This issue found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
