The SPL_STACK config option now depends on having SPL_HAVE_INIT_STACK
defined. This made savedefconfig dropping SPL_STACK when sending the
initial configuration.
Note that SPL/U-Boot are able to boot linux from mass storage with
SPL_STACK not set but other use cases might run out of stack or
overlap with other RAM use.
Compare with:
commit d6a53f523a ("spl: Add an SPL_HAVE_INIT_STACK option")
commit 25fefa05d7 ("configs: Resync with savedefconfig")
Fixes: ff0540fcfe ("board: toradex: add Toradex SMARC iMX95")
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Partitions can be become unusable due to power cuts or failed updates.
Use the bootmeth RAUC if partitions for at least one slot exist. The
bootmeth can then select the working slot.
Signed-off-by: Leonard Anderweit <l.anderweit@phytec.de>
Tested-by: Martin Schwan <m.schwan@phytec.de>
Only check if the root partition exists when scanning for the slots
partitions and not if the filesystem can be accessed. It is not needed
to access the filesystem of the root partition as it might not be
supported by u-boot or be encrypted.
Signed-off-by: Leonard Anderweit <l.anderweit@phytec.de>
Tested-by: Martin Schwan <m.schwan@phytec.de>
The nfsroot constructed as part of the default Analog Devices boot
strategy is missing a semicolon between the server ip and the root path
itself. This adds the missing semicolon.
Signed-off-by: Greg Malysa <malysagreg@gmail.com>
This patch fixes a boot failure on the AM64x EVM that was introduced when the do_board_detect function was removed during a refactoring.
It restores the do_board_detect function for the AM64x, AM62x, and AM65x boards to ensure the common board detection logic is executed correctly.
Fixes: 804b80288a ("board: am65x: Use generic AM6x board detection function")
Fixes: ce56e553c3 ("board: am64x: Use generic AM6x board detection functions")
Fixes: ff1b83c095 ("board: am62x: Add support for reading eeprom data")
Signed-off-by: Guillaume La Roque (TI.com) <glaroque@baylibre.com>
Currently, the bind callback of the driver namely am65_cpsw_nuss_bind()
registers all ethernet ports including the ones that have been disabled
in the device-tree. Since the ports that have been disabled are ought to
be ignored, fix the implementation to register only the enabled ports as
indicated by their 'status' in their respective device-tree node.
Fixes: 3943531a54 ("net: ti: am65-cpsw-nuss: Define bind method for CPSW driver")
Reported-by: Wadim Egorov <w.egorov@phytec.de>
Closes: https://patch.msgid.link/8b4ac072-125c-493b-b12a-f0a4e9d56e7e@phytec.de
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
The helper function "ti_pd_get()" is responsible for powering on a
domain if it is powered off. In the current implementation, if a power
domain is determined to be powered off - no prior users and the PDCTL
register indicates that the user desired state is OFF, then powering on
the domain constitutes setting 'PDCTL_STATE_ON' field of the PDCTL
register.
While the current implementation indeed requests the power domain to be
transition to the ON state, the helper function "ti_pd_get()" doesn't
verify that the power domain has 'transitioned' to the ON state before
returning to its caller. As a result, it is possible that the device(s)
belonging to the power domain may be accessed before it is truly powered
on, leading to a bus abort.
Fix this by waiting for the power domain to transition to the ON state
by using "ti_pd_wait()" before returning from "ti_pd_get()".
Fixes: 144464bd2c ("power: domain: Introduce driver for raw TI K3 PDs")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Tested-by: Hrushikesh Salunke <h-salunke@ti.com>
extension_get_list() will return NULL if there is no extension device.
Check for this situation.
Addresses-Coverity-ID: 638557 - Null pointer dereferences (NULL_RETURNS)
Fixes: 2d12958ee7 ("boot: Remove legacy extension board support")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Acked-by: Kory Maincent <kory.maincent@bootlin.com>
- Move to jammy-20251013 tag
- Bring in tkinter so that FATtools should run and more tests should be
run.
- Update to QEMU 10.0.6
- Pick tags for (most of) trace-cmd
Signed-off-by: Tom Rini <trini@konsulko.com>
We have not been picking a tag for the trace-cmd build process.
Currently the tip of libtraceevent fails to build. Address both problems
here by picking recent stable tags for libtraceevent and libtracefs
(trace-cmd has no recent tags). Further, as it is often reported that
this fails to build due to a race, stop using "make -j$(nproc)" as this
is also small enough of a set of builds to not be an issue.
Signed-off-by: Tom Rini <trini@konsulko.com>
In some cases our tests for exFAT don't run because we fail to be able
to create the underlying image. This is in turn because while creation
of the image succeeds, it seems that some way of how we invoke FATtools
wants to import tkinter, that fails and so the test stops there. Having
tkinter available (and then presumably a fallback to non-GUI because
it's not available) leads to the tests running as expected.
Reviewed-by: Marek Vasut <marek.vasut@mailbox.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The QEMU project has the 10.0.x series as an LTS release. While we are
not doing an LTS ourselves, we can be confident in the changes between
10.0.2 and 10.0.6, so update ourselves.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove setting of fdt_high to ~0, which disables device tree relocation,
from the default environment. Doing so prevents U-Boot from correcting
problems such as having an unaligned device tree and leads to various
failure modes in the OS.
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Doing USB boot on E850-96 is most useful in two cases:
1. For unbricking the board
2. During the bootloader development
In both cases a U-Boot binary is being re-flashed to eMMC. The most
convenient way to update U-Boot in eMMC is by using DFU. Implement
entering DFU flashing mode automatically when U-Boot is executed on USB
boot. That makes it easier for users to re-flash U-Boot without even
having serial console running, e.g.:
$ ./smdk-usbdl
$ dfu-util -D u-boot.bin -a bootloader
See [1,2] for details.
Entering DFU mode is implemented by setting corresponding environment
variables:
bootcmd="dfu 0 mmc 0"
bootdelay=0
Do not save the U-Boot environment though, to avoid falling through to
DFU mode on a regular eMMC boot.
[1] doc/board/samsung/e850-96.rst
[2] https://gitlab.com/LinaroLtd/e850-96/tools/dltool/-/tree/uboot
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
During USB boot it's expected that the bootloader (U-Boot) should
download LDFW and TZSW firmware binaries over USB, using corresponding
SMC call. Once it's done, the Boot ROM code can release the USB block,
so that it can be used in U-Boot (e.g. for flashing images to eMMC using
DFU or fastboot). Otherwise USB wouldn't be accessible in U-Boot, and
any attempt to access USB PHY or DWC3 registers will lead to abort.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
During USB boot U-Boot is supposed to download some firmware over USB.
It's done by EL3 software, so it has to be requested via corresponding
SMC call. Implement a routine for doing that.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The LDFW firmware loading is done in two steps:
1. Read the firmware binary from some block device
2. Provide it to EL3 monitor software via an SMC call, so it can copy
it to a Secure World memory and start using it
Let's split the load_ldfw() function by two functions correspondingly,
to reflect that process better:
- load_ldfw_from_blk()
- init_ldfw()
It can be useful in case when the LDFW binary should be obtained from
some different media, e.g. downloaded over USB during USB boot.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Implement functionality to check the current boot device (a device where
the SoC ROM code is loading the bootloaders from). The boot device order
can be changed using the SW1 DIP switch on the E850-96 board (which
controls XOM SoC lines), as stated in [1].
The boot device information is requested from EL3 software using the
corresponding SMC call, which in turn reads it from iRAM memory, which
was written by the ROM code. New routines decode that data and allow the
user to check the current boot device, boot order, etc. That API can be
used further to implement different code flows depending on the current
boot device, e.g.:
- on eMMC boot: obtain the firmware binaries from eMMC
- on USB boot: download the firmware over USB instead
No functional change; this patch only adds new functionality but it's
not used yet.
[1] doc/board/samsung/e850-96.rst
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Move DRAM init functions close to other public functions, to make things
visually distinct and improve the readability.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
mu@27020000 is required for communication with ELE firmware, and
lpuart5 is the standard output device. Both peripherals must be
available before U-Boot relocation. Use bootph-all instead of
bootph-pre-ram so these nodes are retained across all boot phases.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
In TEZI (Toradex Easy Installer), we use one U-Boot binary for both our
NAND and eMMC Colibri iMX7 modules. Currently, CONFIG_PREBOOT sets the
environment variable 'fdtfile' depending on which defconfig was used,
adding the '-emmc' variant for the emmc defconfig. Since we always build
the TEZI recovery U-Boot with the standard (non-emmc) defconfig, fdtfile
has to be overwritten later or it will be wrong there.
By using '$variant', the fdtfile var is properly constructed at run time
for both the NAND and eMMC variants, and we do not have to worry about
setting fdtfile again when building the recovery TEZI U-Boot.
This also synchronizes these configs with how we handle the iMX6ULL.
Fixes: 327381e8b5 ("colibri_imx7: use preboot for fdtfile evaluation")
Signed-off-by: Ernest Van Hoecke <ernest.vanhoecke@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Fix macros for the GPIO function for two pads (ENET1_TD3 and I2C2_SCL),
aligning them to the functions specified in the datasheet.
Fixes: a9d562daa3 ("imx: Add iMX91 support")
Suggested-by: Javier Viguera <javier.viguera@digi.com>
Signed-off-by: Francesco Valla <francesco@valla.it>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
There is a condition guard which ensures that the GPIO node, indeed
describes a GPIO controller.
if (!fdtdec_get_bool(blob, node, "gpio-controller"))
continue;
Since the bank base is being incremented in the loop, it is done so
irrespective of whether the node is a GPIO controller or not. This leads
to the incorrect resolution of bank base addresses.
Move it out of the loop, and instead increment the bank base address
only if the driver successfully binds a GPIO controller.
Reviewed-by: Henrik Grimler <henrik@grimler.se>
Fixes: b8809e60cd ("dm: exynos: gpio: Convert to driver model")
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The fdt_addr variable is used in extlinux as a fallback devicetree if
none is provided by the boot command. Otherwise the only use in U-Boot
seems to me efi_install_fdt() when the internal FDT is required.
The existing mechanism uses the devicetree provided to U-Boot, but in
its original, unrelocated position. In my testing on an rpi_4, this ends
up at 2b35ef00 which is not a convenient place in memory, if the ramdisk
is large.
U-Boot already deals with this sort of problem by relocating the FDT
to a safe address.
So use the control-FDT address instead.
Remove the existing comment, which is confusing, since the FDT is not
actually passed unmodified to the kernel: U-Boot adds various things
using its FDT-fixup mechanism.
Note that board_get_usable_ram_top() reduces the RAM top for boards with
less RAM. This behaviour is left unchanged as there is no other
mechanism for U-Boot to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Christopher Obbard <christopher.obbard@linaro.org>
Tested-by: Christopher Obbard <christopher.obbard@linaro.org> # CM4 1G
This patch adds support for configuring GPIO pull-up and pull-down
resistors in the BCM283x pinctrl driver. It implements the brcm,pull
device tree property to control pin bias settings.
The implementation follows the hardware-specific pull control
mechanisms:
- BCM2835: two-step GPPUD register sequence
- BCM2711: direct per-pin control registers
This enables device tree configurations to specify pull-up, pull-down,
or no bias for individual GPIO pins.
Tested on Raspberry Pi boards with both BCM2835 and BCM2711 SoCs.
Signed-off-by: Cibil Pankiras <cibil.pankiras@egym.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Tom reports that adding more Kconfig options fails with
board/raspberrypi/rpi/lowlevel_init.o: in function `save_boot_params':
board/raspberrypi/rpi/lowlevel_init.S:20:(.text+0x0):
relocation truncated to fit: R_AARCH64_ADR_PREL_LO21
against symbol `fw_dtb_pointer' defined in .data section
in board/raspberrypi/rpi/rpi.o
make: *** [Makefile:2029: u-boot] Error 1
Since fw_dtb_pointer lives in .data it might end up above the
+-1MB that adr can reach.
So switch over to adrp+add which has a +-4gb reach.
Reported-by: Tom Rini <trini@konsulko.com>
Closes: https://source.denx.de/u-boot/custodians/u-boot-raspberrypi/-/issues/2
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
The SCMI shared memory area is no longer automatically marked as
non-cacheable after the commit a5a0134570 ("firmware: scmi: Drop
mmu_set_region_dcache_behaviour() misuse").
This change in behavior cause Rockchip RK3588 boards to fail boot with:
SoC: RK3588
DRAM: 8 GiB
scmi-over-smccc scmi: Channel unexpectedly busy
scmi_base_drv scmi-base.0: getting protocol version failed
scmi-over-smccc scmi: failed to probe base protocol
initcall_run_r(): initcall initr_dm() failed
### ERROR ### Please RESET the board ###
Update the memory mapping on RK3588 to mark the SCMI shared memory area
as non-cacheable to fix the SCMI shared memory based transport issue
that prevented RK3588 boards from booting.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Introduce fastboot block flashing functions and helpers
to be shared with the MMC implementation.
The write logic comes from the mmc implementation, while
the partition lookup is much simpler and could be extended.
For the erase logic, allmost no block drivers exposes the
erase operation, except mmc & virtio, so in order to allow
erasiong any partition a soft-erase logic has been added
to write zero-ed buffers in a loop.
Signed-off-by: Dmitrii Merkurev <dimorinny@google.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Tested-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20251121-topic-fastboot-blk-v7-1-9589d902fc91@linaro.org
Signed-off-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Fix two memory allocation bugs in label_boot_extension():
1. When label->fdtdir is not set, overlay_dir was used without any
memory allocation.
2. When label->fdtdir is set, the allocation size was incorrect,
using 'len' (just the fdtdir length) instead of 'dir_len' (which
includes the trailing slash and null terminator).
Resolve both issues by moving the memory allocation and string
formatting outside the conditional block, resulting in clearer code
flow and correct sizing in all cases.
Closes: https://lists.denx.de/pipermail/u-boot/2025-November/602892.html
Addresses-Coverity-ID: 638558 Memory - illegal accesses (UNINIT)
Fixes: 935109cd9e ("boot: pxe_utils: Add extension board devicetree overlay support")
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Tested-by: Surkov Kirill <fanra3.tk@gmail.com>
Size of array buf was incorrect due to sizeof returning the
size of an integer (typically 32 bits) instead of a u64 type
(64 bits). Hence, buf array was shorter than expected.
Signed-off-by: Francois Berder <fberder@outlook.fr>
Reviewed-by: Simon Glass <sjg@chromium.org>
Pull request efi-2026-01-rc3-2
CIL https://source.denx.de/u-boot/custodians/u-boot-efi/-/pipelines/28454
Documentation:
* board: ti: am6254atl_sk: correct value of PRELOADED_BL33_BASE
* pytest: fix u-boot-test-flash typo
* samsung: Fix PXE description for the E850-96 board
* board: ti: k3: Update TI firmware repository URL to GitHub
* add missing macro descriptions to include/test/ut.h and add it to
the API documenation
* rearrange the description of DM tests and describe return values
Testing:
* Enable CI testing ACPI on qemu-riscv64_smode_acpi_defconfig
* Add qemu-riscv64_smode_defconfig to the CI tests
* Generalize tests such that they can run on RISC-V QEMU
- fdt_test_apply requires CONFIG_OF_LIBFDT_OVERLAY
- cmd/fdt: do not assume RNG device exists
- cmd/bdinfo: make no flash assumption
- cmd/bdinfo: consider arch_print_bdinfo() output
- common/print: do not use fixed buffer addresses
- cmd/fdt: do not use fixed buffer addresses
- raise CONFIG_CONSOLE_RECORD_OUT_SIZE default to 0x6000
* enable CONFIG_CONSOLE_RECORD=y on qemu-riscv64_smode_acpi
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAmkg1IsACgkQxIHbvCwF
# GsQVLA//dmiApob+J9FUhD8joD+DaKSNfLYmv8zwfIFL2xRxx7D+CQT+r+I9FJYI
# KojiLyn4PE/5VOm+wrsvAoYoMLJwAHvg5nmYJLLzvm6V//DLd1AEopP/+Uh8gEVW
# xYGLcvDyGgZpraAhcmqRnAS89py3SigwGzhcUMbT6ZC6pgMVEsBpg8XeMpY7N05c
# rwyqFAAPD8RcF7veQCpry87NiK5o+9YuM1zKl5sDFOpEWKq5ToNwhQ00bnux9lUd
# HWz9X6ge58iFiMXRqUCnOaPeXeChn9ejyEiKtfQ0JtykOf9NT2WMdD2VKe9PCYsd
# f7OynJTGG2OXTKBhon/xj75itiTm7EELc/FHwHEdtZIIHgpi/C33yQgKxLf9mtUo
# Z7DKYpPoaTCbJhs9LCK942KPtshbtAJLKTVqyBPo7Jn0mneeCQUsbaQRU7JruJTK
# hKluUjsAry3Do3wv/w6B8R6MMgfpBktPkqjg9e/maSdhYdkNAYpjajtORgpqmJRV
# HTGJXfL3qFC50jlenlMYOm4Qake33MIMzubaxoM3j5ENDUJ7KAbWADEoWDpve8Tu
# b/fX8uuW+g2T18Y/M9Bsk/jaUjDTx0xtZUSYNIIQJFDaJMzUxGYWlmtXhLZwFU8g
# 7S5pBmgxoSAtQSMAeoJPJp9FSgXYqiGLUeSwcOH2NaPn0lLFvK0=
# =D0Yy
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 21 Nov 2025 03:07:23 PM CST
# gpg: using RSA key 6DC4F9C71F29A6FA06B76D33C481DBBC2C051AC4
# gpg: Good signature from "Heinrich Schuchardt <xypron.glpk@gmx.de>" [unknown]
# gpg: aka "[jpeg image of size 1389]" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6DC4 F9C7 1F29 A6FA 06B7 6D33 C481 DBBC 2C05 1AC4
