These files had '#include<file.h>' rather than '#include <file.h>' which
while functional is not the correct style.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add the HBMC and MUX_MMIO configs in the R5 SPL stage for
successful HBMC boot.
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
The commit 210702ae6c ("spl: spi: fix falcon mode for spi boot") fixed
the logic of spl_start_uboot() where 0 means OS boot and 1 means u-boot.
Zynq/ZynqMP enable OS_BOOT by default but it was never really be used
that's why disable it to boot via U-Boot phase all the time.
Signed-off-by: Michal Simek <michal.simek@amd.com>
This patch is used to restore support for i.MX95 A0 silicon. To avoid
duplicating defconfig, imx95.config is added and can be shared between
imx95_a0_19x19_evk_defconfig and imx95_19x19_evk_defconfig.
container.cfg and imximage.cfg are used to created .cfgout files that
are be passed to mkimage with -n to build flash.bin. Now they have been
deleted and replaced by adding their content to properties of node which
type is nxp-imx9image under binman node.
Fixes: 9936724aa9 ("imx95_evk: Add i.MX95 B0 support")
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Tested-By: Tim Harvey <tharvey@gateworks.com> # imx95-19x19-evk (rA0)
Enable CONFIG_DNS for visionfive2 board target. With CONFIG_PROT_DNS_LWIP
enabled and CONFIG_CMD_DNS disabled this restores DNS functionality
displaced by LwIP DNS refactoring during the merge window.
Signed-off-by: E Shattow <e@freeshell.de>
Booting u-boot as payload with coreboot's main branch is currently broken
since commit [1] on x86 as U-boot assumes the active GDT matches what
U-Boot would have installed in start16.S.
Make no assumptions and always load the GDT when building as coreboot
payload to make sure the segment registers are actually matching the GDT.
Fixes #GP seen when booting U-Boot as coreboot payload.
1: https://review.coreboot.org/c/coreboot/+/87255
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://review.coreboot.org/c/coreboot/+/87255
Reviewed-by: Tom Rini <trini@konsulko.com>
Avoid use of hard-coded address in boot command, instead use $loadaddr
which is the default load address. This improves consistency of the
environment on this board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The CONFIG_ENV_VARS_UBOOT_CONFIG extends U-Boot environment with
variables arch/board/board_name/soc/vendor, which can be used to
discern different devices from each other based purely on U-Boot
environment variables.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
LAN9514 is a chip on E850-96 board which acts as a USB host hub and
Ethernet controller. It's controlled via USB lines when DWC3 is
configured to be in USB host role (by setting the "dr_mode" property to
"host" value in e850-96 dts file).
Enable network support and LAN9514 chip support. This makes Ethernet
functional on E850-96 board.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Exynos850 SoC has a dual-role USB controller which can be configured in
USB host role. As it's the only one USB controller on the board, it's
shared between "device" USB connector (micro-USB) and host USB
connectors. The hardware automatically powers on the host related parts
when the micro-USB cable (for device role) is being disconnected. Also,
as U-Boot lacks dynamic USB role switching capability, the only way to
switch the role at the moment is to modify "dr_mode" property in
U-Boot's device tree file here:
dts/upstream/src/arm64/exynos/exynos850-e850-96.dts
This won't affect the dynamic role switching later in Linux kernel, as a
separate (different) device tree blob is provided to the kernel.
Enable the USB host support and corresponding commands to make it
functional in E850-96 board.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Linux kernel should use some separate device tree obtained from another
source anyway. For example the dtb file can be read from /boot directory
in eMMC rootfs partition, either by GRUB or U-Boot. Using U-Boot's
device tree blob to provide it to the kernel (when
CONFIG_DEFAULT_FDT_FILE is set and nobody else overrides this choice)
might lead to undesired effects when booting the OS. For example, if a
user sets "dr_mode" property to "host" value in U-Boot's dts to enable
USB host capabilities in U-Boot, it might confuse usb-conn-gpio driver
in Linux kernel later like this:
platform connector: deferred probe pending: usb-conn-gpio:
failed to get role switch
Disable CONFIG_DEFAULT_FDT_FILE option to avoid any possible confusion.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
After the commit 7a53abb183 ("rockchip: rk3588: Remove USB3 DRD nodes
in u-boot.dtsi") was merged for v2024.10 there is no reason to keep the
usb nodes for the Generic RK3588 board in the board u-boot.dtsi.
Move usb related nodes from board u-boot.dtsi to main board device tree.
While at it, also drop use of the usb3-phy as we only want to enable the
usb2-phy to be compatible with as many boards as possible.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the needed modules so that ROCKUSB can be used to update the
NanoPi R5S.
Signed-off-by: Diederik de Haas <didi.debian@cknow.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Radxa E20C has a USB OTG Type-C port for Debug and Data.
Add required Kconfig options to use USB gadget features once pending
USB nodes finally lands in dts/upstream by a future sync.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
GPIO0_B7 is routed to TXI of the on-board CAN transceiver. The
line has a pull-down per SoC default.
This means the CAN transceiver transmits a dominant zero
and blocks the CAN bus until Linux boots and reconfigures the pin.
Let's switch to pull-up as soon as we can (i.e. in SPL).
This cuts down the "bus is blocked" time from 10 seconds to < 1 second.
Of course, to this needs CONFIG_SPL_BOARD_INIT, so enable it
the Jaguar defconfig.
Signed-off-by: Jakob Unterwurzacher <jakob.unterwurzacher@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Erasing the environment to start from scratch is actually very useful
and "env erase" is the proper way to do it instead of using "env
default -a && env save", so let's enable support for it.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Erasing the environment to start from scratch is actually very useful
and "env erase" is the proper way to do it instead of using "env
default -a && env save", so let's enable support for it.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Erasing the environment to start from scratch is actually very useful
and "env erase" is the proper way to do it instead of using "env
default -a && env save", so let's enable support for it.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Erasing the environment to start from scratch is actually very useful
and "env erase" is the proper way to do it instead of using "env
default -a && env save", so let's enable support for it.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
ArmSoM-Sige5 adopts the second-generation 8nm high-performance AIOT
platform Rockchip RK3576, with a 6 TOPS computing power NPU and support
for up to 16GB of large memory. It supports 4K video encoding and
decoding, offers rich interfaces including dual gigabit Ethernet ports,
WiFi 6 & BT5, and various video outputs.
Features tested on a ArmSoM Sige5 v1.1:
- SD-card boot
- eMMC boot
- Ethernet
- PCIe NVMe
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a minimal generic RK3576 board that only have eMMC, SDMMC and USB
OTG enabled. This defconfig can be used to boot from eMMC or SD-card on
most RK3576 boards that follow reference board design.
eMMC and SD-card boot tested on:
- ArmSoM CM5
- ArmSoM Sige5
- FriendlyElec NanoPi M5
- Luckfox Omni3576
- Toybrick TB-RK3576D
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Initially, only one STM32MP25 based board was available, the
stm32mp257f-ev1 board which was set by default in stm32mp25_defconfig.
Since commit 79f3e77133 ("Subtree merge tag 'v6.16-dts' of dts repo [1] into dts/upstream")
we inherited of a second MP25 based board which is the stm32mp257f-dk board.
Enable OF_UPSTREAM_BUILD_VENDOR and set OF_UPSTREAM_VENDOR to allow all
STMicroelectronics DT compilation.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Fix PHYTEC EEPROM bus mismatch between SPL and U-Boot proper by enabling
CONFIG_SPL_DM_SEQ_ALIAS=y on phyCORE-i.MX93 boards. This way, both the
SPL and U-Boot proper will respect the device-tree aliases for I2C devs
and use the same I2C bus number for phytec_eeprom_data_setup() function
calls. This makes code less confusing and more robust.
Fixes an issue apparent since commit 79f3e77133 ("Subtree merge tag
'v6.16-dts' of dts repo [1] into dts/upstream") where SPL would spew the
following error:
phytec_eeprom_read: i2c EEPROM not found: -110.
phytec_eeprom_data_setup: EEPROM data init failed
While later in U-Boot proper, EEPROM would be successfully read out.
This happens because Linux device-tree for phyBOARD-Segin-i.MX93 since
aforementioned commit enables I2C bus 2 (lpi2c2 is used for audio codec
and RTC) which breaks SPL I2C bus number ordering and I2C EEPROM bus is
shifted by +1. Now, lets prevent this from happening again by utilizing
device-tree aliases also in the SPL.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
The Nano's SPI flash stopped working in U-Boot, as the prior stage loaded
U-Boot, the only thing it was used for was save/loading env vars so update
the DT so it can now initialise it. It also drops enabling the old
TEGRA114_SPI driver, as the flash hangs off the faster TEGRA210_QSPI
interface, nothing on the Nano uses the old interface by default so it's
surplus.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The Jetson Nano contains all it's firmware on a 4Mb SPI flash, the
allocated size in that flash for U-Boot is 753664 bytes so we need to
ensure the u-boot.bin doesn't exceed that else it will fail.
Add a BOARD_SIZE_LIMIT and drop a few large, and somewhat esoteric, options
to bring us back under that limit.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Surface 2 is a Surface-series Windows RT hybrid tablet computer created by
Microsoft. Surface 2 uses a 1.7 GHz quad-core Nvidia Tegra 4 chipset with
2 GB of RAM, features 10.6 inch FullHD ClearType HD screen with 16:9 aspect
ratio and 32/64 GB of internal memory that can be supplemented with a
microSDXC card giving up to 64 GB of additional storage.
Signed-off-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The Renesas board defconfigs explicitly set CONFIG_TEXT_BASE=0x50000000,
however U-Boot's POSITION_INDEPENDENT=y build default already places text
at 0x0. These hardcoded overrides are therefore unnecessary and will be
pruned automatically in upcoming resyncs.
Remove the CONFIG_TEXT_BASE lines from the following defconfigs:
- hihope_rzg2_defconfig
- r8a77970_eagle_defconfig
- r8a77970_v3msk_defconfig
- r8a77990_ebisu_defconfig
- r8a77995_draak_defconfig
- r8a779a0_falcon_defconfig
- renesas_rzg2l_smarc_defconfig
- rz2_beacon_defconfig
- silinux_ek874_defconfig
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Enable support for PCIe based xHCI USB 3.0 driver and USB mass
storage support on Retronix R-Car V4H Sparrow Hawk board .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Enable CONFIG_OF_BOARD_SETUP and other dependencies to allow the use of
the ft_board_setup() function to replace fdt set in boot scripts for
Microchip's MPFS Icicle kit.
Signed-off-by: Jamie Gibbons <jamie.gibbons@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The commit d92fdb6067 ("binman: Add option for pointing to separate
description") added support for separating binman description to own file
not the be the part of DT for OS.
The main reason is that binman is not passing dt schema validation that's
why want to keep it separated.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Acked-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Increase Icicle's SYS_BOOTM_LEN to 0x4000000 which is the new default
value.
Done on Conor Dooley's request.
Signed-off-by: Martin Herren <sputnik@on-the-web.ch>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Remove CONFIG_SYS_BOOTM_LEN from all riscv defconfigs where the new
default value is used.
Signed-off-by: Martin Herren <sputnik@on-the-web.ch>
Acked-by: Michal Simek <michal.simek@amd.com> # xilinx_mbv
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
For all riscv defconfigs that use the current default value.
This is done in provision of changing the default value to the most
common used value of 0x4000000.
Signed-off-by: Martin Herren <sputnik@on-the-web.ch>
Acked-by: Michal Simek <michal.simek@amd.com> # xilinx_mbv
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
58e9502e6 "arm: sunxi: Enable SPL/SPI boot for Olinuxino Lime2-eMMC
boards" enabled SPI boot for the eMMC variant. Olimex offers the
"s16MB" variant with SPI flash populated but without eMMC populated.
Tested on board rev L.
Signed-off-by: Eric Anderson <ejona86@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The pinecube has an ethernet connector which uses the EMAC and internal
PHY of the chip. Enable it in the config.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
The first of the two Ethernet controllers in the Allwinner A527/T527 is
compatible to the MAC from the previous SoCs. Consequently the recent DT
update brought use the MAC node, using the A64 compatible string as the
fallback, which works out of the box.
Enable the sun8i-emac Ethernet driver in the defconfig for the Radxa and
the Avaota boards, so that kernels and other data can be loaded via
TFTP. Please note that only one of the Ethernet sockets will work, the
second MAC is not compatible, and needs a new U-Boot driver. The
X96QPro+ TV box unfortunately uses only this second EMAC, so Ethernet
cannot be used there at the moment.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The V3s (using co-packaged DRAM) runs at 360 MHz, which is specified in
the common platform Kconfig file. However the value for MACH_SUN8I will
be picked up instead due to ordering.
Re-order the defaults to have MACH_SUN8I_V3S before MACH_SUN8I and let
it select the correct default. Also update the LicheePi Zero Dock
defconfig to remove the value, which is now correctly selected.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
There is nothing special for u-boot in the V3/V3s device-tree files,
they are just copies of the upstream ones.
Remove the copies and switch to OF_UPSTREAM for supported boards.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
