When tests are all in the same suite it is annoying to have to read all
the common text after each name. Skip this to help the user.
Signed-off-by: Simon Glass <sjg@chromium.org>
Show the average duration of a test, so we can keep track of how it is
trending. Report the suite with the longest average test to encourage
people to improve it.
Add a function to update the stats based on the results from a single
suite and another to show the summary information.
Make this optional, since sandbox's SPL tests do not have a timer driver
and people may want to print results without times.
Signed-off-by: Simon Glass <sjg@chromium.org>
Show the time taken by each test suite with 'ut all' and the total time
for all suites.
Take care to remove any sandbox time-offset from the values.
Fix the comment-format on timer_test_add_offset() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
All tests should belong to a suite, but if there is a suite we don't
know about (e.g. not added to cmd_ut.c) then the totals will not add up.
Add a check for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
This test does not appear to use sandbox's memory-mapped I/O so there is
no need to enable it.
Even if there were a need, it should be disabled at the end of the test,
so as not to affect other tests.
Drop these lines from the test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Harrison Mutai <harrison.mutai@arm.com> says:
This series of patches enhances the vexpress64 platform by enabling bloblist
support. It also introduces support for CONFIG_BLOBLIST_PASSAGE. This is
necessary to boot vexpress64 and other boards without manually specifying a
fixed address and size for the bloblist.
After this change, all the bloblist init modes are supported (i.e., fixed,
alloc, passage) and Vexpress64 boots with CONFIG_BLOBLIST_PASSAGE.
Link: https://lore.kernel.org/r/20250204175844.19890-1-harrison.mutai@arm.com
Enable bloblist on vexpress64 platforms to facilitate information
passing from TF-A using the firmware handoff framework.
Signed-off-by: Harrison Mutai <harrison.mutai@arm.com>
When the configuration option CONFIG_BLOBLIST_PASSAGE is selected, the
bloblist present in the incoming standard passage is utilised in-place.
There is no need to specify the size of the bloblist as the system
automatically detects it using the header information.
Signed-off-by: Harrison Mutai <harrison.mutai@arm.com>
When booting into the Linux kernel with semi-hosting, use the device
tree provided by hardware unless one is provided in the current
directory.
Signed-off-by: Harrison Mutai <harrison.mutai@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
u-boot-dfu-20250211:
CI:
- https://source.denx.de/u-boot/custodians/u-boot-dfu/-/pipelines/24556
Android:
- Handle boot images with missing DTB
Usb gadget:
- Fix nullptr in g_dnl when serial# is unset
- Add missing schedule() in f_mass_storage gadget
- Add support for STih407 in dwc3-generic
- Fix usb clocks on STih407
- Migrate STih407 to DM_USB_GADGET
- Check return value of xrealloc for NULL.
- Free allocated memory and return NULL if xrealloc fails.
- Prevent NULL pointer dereference in strlen and strcat.
Triggers found by static analyzer Svace.
Signed-off-by: Anton Moryakov <ant.v.moryakov@gmail.com>
- Check return value of malloc_cache_aligned for presskey and sha.
- Return -ENOMEM if memory allocation fails.
- Free allocated memory in error paths."
Triggers found by static analyzer Svace.
Signed-off-by: Anton Moryakov <ant.v.moryakov@gmail.com>
Dynamic memory, referenced by 'line', is allocated by calling
function 'calloc' and lost when the function terminates with code -1.
Signed-off-by: Maks Mishin <maks.mishinFZ@gmail.com>
Dynamic memory, referenced by 'line', is allocated at ublimage.c:159
by calling function 'getline' and lost at ublimage.c:184.
Signed-off-by: Maks Mishin <maks.mishinFZ@gmail.com>
Report of the static analyzer:
1. NULL_AFTER_DEREF Pointer 'str', which is dereferenced at
image-host.c:688 by calling function 'strdup', is compared to a NULL
value at image-host.c:691.
2. NULL_AFTER_DEREF Pointer 'list', which is dereferenced at
image-host.c:689, is compared to a NULL value at image-host.c:691.
Corrections explained:
1. Checking for NULL before using pointers: The if (!list || !str) check
is now performed before calling strdup and realloc, which prevents
null pointer dereferences.
2. Checking the result of strdup: strdup can return NULL if memory
allocation fails. This also needs to be checked.
3. Checking the result of realloc: If realloc returns NULL, then memory
has not been allocated and dup must be freed to avoid memory leaks.
Triggers found by static analyzer Svace.
Signed-off-by: Anton Moryakov <ant.v.moryakov@gmail.com>
Since commit 6aa8bde878 ("usb: host: ehci-generic: Remove DM_REGULATOR
flag") device_get_supply_regulator() returns -ENOSYS which is not handle
by ehci_enable_vbus_supply() and thus, ehci_usb_probe() return an error.
By enabling DM_REGULATOR flag, device_get_supply_regulator() return -ENOENT
which is handle and ehci_usb_probe() return 0.
This fixed the following issue:
stih410-b2260 =>usb start
starting USB...
Bus dwc3@9900000: Register 2000240 NbrPorts 2
Starting the controller
USB XHCI 1.00
Bus usb@9a03c00: USB OHCI 1.0
Bus usb@9a03e00: probe failed, error -38
Bus usb@9a83c00: USB OHCI 1.0
Bus usb@9a83e00: probe failed, error -38
scanning bus dwc3@9900000 for devices... 1 USB Device(s) found
scanning bus usb@9a03c00 for devices... data abort
pc : [<7df929b4>] lr : [<7df92918>]
reloc pc : [<7d6409b4>] lr : [<7d640918>]
sp : 7c73b848 ip : 9cf13c5c fp : 7c879d08
r10: 7c85d040 r9 : 7c74ded0 r8 : 09a03c00
r7 : 00000002 r6 : 7c85d080 r5 : 7c86a040 r4 : 00000000
r3 : 00000000 r2 : 00000000 r1 : 7c85d080 r0 : 7c85d040
Flags: nzCv IRQs off FIQs off Mode SVC_32
Code: 05853ae4 0affffe2 e59a2010 e59a300c (e5832010)
Resetting CPU ...
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20250130163547.512990-3-patrice.chotard@foss.st.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
On STi platforms, all clocks are enabled by BOOTROM, so CONFIG_CLK is
not set as no clock driver for STI exists.
As ehci-generic and ohci-generic drivers are used on platforms where
CONFIG_CLK is set, clk_get_bulk() returns-ENOSYS in case of
stih410-b2260.
To avoid this error, add fixed clocks for ehci and ohci nodes for
stih410-b2260 to fix the following errors:
Bus usb@9a03c00: ohci_generic usb@9a03c00: Failed to get clocks (ret=-19)
Port not available.
Bus usb@9a03e00: ehci_generic usb@9a03e00: Failed to get clocks (ret=-19)
Port not available.
Bus usb@9a83c00: ohci_generic usb@9a83c00: Failed to get clocks (ret=-19)
Port not available.
Bus usb@9a83e00: ehci_generic usb@9a83e00: Failed to get clocks (ret=-19)
Port not available.
scanning bus dwc3@9900000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20250130163547.512990-2-patrice.chotard@foss.st.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
The rules part of the template makes sure that this doesn't run until
specifically requested. Drop the check in the script itself, so it is
possible to trigger a run manually without re-pushing the tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Judith Mendez <jm@ti.com> says:
This patch series enables ESM reset configuration in board_init_f
for am62x and am62px devices.
This is necessary in order for error events to reset the system.
This patches are tested using watchdog to reset the system via ESM.
Link: https://lore.kernel.org/r/20250129234403.574766-1-jm@ti.com
Enable CONFIG_SPL_DRIVERS_MISC, CONFIG_SPL_MISC, CONFIG_ESM_K3
to probe the Main ESM and MCU ESM nodes.
Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
Signed-off-by: Judith Mendez <jm@ti.com>
On AM62A and AM62P devices, it is possible to route Main ESM error
events to MCU ESM. MCU ESM high error output can trigger the reset
logic to reset the device. So, for these devices we have Main ESM and
MCU ESM nodes in the device tree. Add functions to probe these nodes
if CONFIG_ESM_K3 is enabled.
Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
Signed-off-by: Judith Mendez <jm@ti.com>
Add the optargs variable so that we can set optional arguments while
booting.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
The env_fat_get_dev_part() function mostly returns a fixed string, set
via some Kconfig variable. However when the first character is a colon,
that means that the boot device number is determined at runtime, and
patched in. This requires altering the string.
So far this was done via some ugly and actually illegal direct write to
the .rodata string storage. We got away with this because U-Boot maps
everything as read/write/execute so far.
A proposed patch set actually enforces read-only (and no-execute)
permissions in the page tables, so this routine now causes an exception:
=======================
Loading Environment from FAT... "Synchronous Abort" handler, esr 0x9600004f, far 0xfffb7d4c
elr: 000000004a054228 lr : 000000004a05421c (reloc)
elr: 00000000fff7c228 lr : 00000000fff7c21c
.....
=======================
Rewrite the routine to do away with the dodgy string manipulation,
instead allocate the string in the r/w .data section, where we can
safely manipulate it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Siddharth Vadapalli <s-vadapalli@ti.com> says:
Hello,
This series re-enables MUX_MMIO at U-Boot proper on J721E and J7200
SoCs. The commits which introduced support for Hyperflash boot on both
of these SoCs disabled MUX_MMIO functionality at U-Boot proper, thereby
introducing a regression.
Series is based on commit
2b1c8d3b2d cmd: Fix Kconfig coding style
of the master branch of U-Boot.
Link: https://lore.kernel.org/r/20250201091809.1894892-1-s-vadapalli@ti.com
Commit under Fixes introduced support for Hyperflash boot but also disabled
MUX_MMIO support at U-Boot proper. MUX_MMIO is required at U-Boot proper
to setup the SERDES Lane Mapping as described by the device-tree. On J7200
SoC, PCIe functionality is broken since commit under fixes.
Fix this regression by re-enabling MUX_MMIO.
Fixes: 038f6faea9 ("configs: j7200_evm_*_defconfig: Add configs for Hyperflash boot")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Anurag Dutta <a-dutta@ti.com>
Commit under Fixes introduced support for Hyperflash boot but also disabled
MUX_MMIO support at U-Boot proper. MUX_MMIO is required at U-Boot proper
to setup the SERDES Lane Mapping as described by the device-tree.
Fix this regression by re-enabling MUX_MMIO.
Fixes: fd7fcd4098 ("configs: j721e_evm_*_defconfig: Add configs for Hyperflash boot")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
emul_rtc_probe() is not called from anywhere else that's why make it
static. Issue is reported by build with W=1.
Signed-off-by: Michal Simek <michal.simek@amd.com>
This patch enables switch auto-detction for mt7981 as some new mt7981
boards will use AN8855 ethernet switch.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Enable configs required for detecting and fixing up for different RAM variants.
Also resync after savedefconfig.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Tested-by: Daniel Schultz <d.schultz@phytec.de>
Detect RAM size via EEPROM and adjust DDR size and banks accordingly.
Include necessary fixups to handle ECC-enabled configurations.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Tested-by: Daniel Schultz <d.schultz@phytec.de>
Add bootph-all properties to I2C0 nodes to ensure the bus and EEPROM
are accessible across all stages. This enables reading the SoM
configuration at any point during the boot process.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Tested-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
USB tests on ext partitions can fail with the following output
test/py/tests/test_usb.py:245: in test_usb_part
'fstype usb %d:%d' % i, part_id
E TypeError: not enough arguments for format string
So add brackets around the format string arguments to prevent the
error.
Fixes: a730947974 ("test/py: usb: Distinguish b/w ext2/ext4 partitions")
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Love Kumar <love.kumar@amd.com>
The change from pinctrl to pio was missing in mt7986-u-boot.dtsi and will
cause build failure. Now fix it.
Fixes: f1775996ba (mediatek: mt7986: move gpio-controller up and rename pinctrl to pio)
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch add support to read register base address by name if
provided.
Also devfdt_get_addr_* is changed to dev_read_addr_* to support DT
live tree.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The reg-names in mt7988.dtsi have no _base suffix. Remove the suffix
will also make it match upstream linux format.
Fixes: 8c2cb748ef (pinctrl: mediatek: mt7988: rename reg-names to upstream linux format)
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
