For the Tegra 2, similar to other Tegra SoC generations, 'bootph-all'
must be applied to both display controllers.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
While PLLD/D2 is the nominal parent clock, all derived clocks are generated
from its single output, plld_out0, which is PLLD/D2 divided by two. Direct
use of PLLD/D2 is absent in peripheral clock configurations. Therefore,
clock derivation formulas must take in account this division.
Signed-off-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Older EDID timing algorithms relied solely on detailed timings, typically
optimized for a display's native resolution. This caused issues with newer
4K panels on older hardware, which couldn't handle those high resolutions.
To address this, the algorithm now also considers standard timings, offering
lower, compatible resolutions. Future improvements may include checking
established timings for even broader compatibility.
Signed-off-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The Mi Pad is a tablet computer based on Nvidia Tegra K1 SoC which
originally ran the Android operating system. The Mi Pad has a 7.9" IPS
display with 1536 x 2048 (324 ppi) resolution. 2 GB of RAM and 16/64 GB of
internal memory that can be supplemented with a microSDXC card giving up to
128 GB of additional storage.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Using HTTPS without root (CA) certificates is a security issue. Print a
warning in this case. Also, when certificate verification fail, print
an additional message because "HTTP client error 4" is not very
informative (4 is HTTPC_RESULT_ERR_CLOSED).
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Instead of relying on some build time configuration to determine if
server certificates need to be checked against CA certificates, do it
based on the availability of such certificates. If no CA is configured
then no check can succeed; on the other hand if we have CA certs then
we should not ignore them. It is always possible to remove the CA certs
(via 'wget cacert 0 0') to force an HTTPS download that would fail
certificate validation.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Some boards use a CONFIG option to specify the value of this variable.
This is normally handled by efi_get_distro_fdt_name() but in the case
of sunxi this does not work, since 'soc' is sunxi, but the files are
in the allwinner directory.
Provide a work-around for this particular case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Pull request efi-next-20250310
CI:
* https://source.denx.de/u-boot/custodians/u-boot-efi/-/pipelines/25043
UEFI:
* Clean up usage of structure jmp_buf_data
* Refactor EFI network protocol implementation for future support
of multiple network interfaces.
- efi_net: let efi_net_set_dp properly update the device path
- expose symbols to be used by the EFI network stack
- efi_setup: Add efi_start_obj_list() to efi_setup.c
- efi_net: Add efi_net_do_start() to efi_net.c
- efi_device_path: Pass net udevice as argument
- efi_net: Add device path cache
- efi_net: Add dhcp cache
- efi_net: Add support for multiple efi_net_obj
Others:
* legacy-net: wget: fix wget_info handling after new tcp legacy stack
* lib: correct description of CONFIG_SYS_FDT_PAD
* Separate setjmp.h into architecture dependent and independent parts
- sandbox: remove linux/types.h dependency in setjmp.h
- arm: include asm-generic/int-ll64.h in setjmp.h
- common: clean up setjmp.h
* arm: use type jmp_buf instead of struct jmp_buf_data
Enable support for environment in eMMC on STM32MP13xx DHCOR SoM,
in addition to existing support for environment in SPI NOR. The
environment size is the same, except in case the environment is
placed in eMMC, it is stored at the end of eMMC BOOT partitions
in the last 32 sectors of each eMMC HW BOOT partition.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The Linux cmdline encoded in the defconfig is wrong, the
STM32 USART driver registers as ttySTM0 not ttyS0.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Move stm32mp15_dhcom_basic_defconfig into stm32mp15_dhcom_basic.config.
Retain legacy stm32mp15_dhcom_basic_defconfig as multi-config for all
DH STM32MP15xx DHCOM based boards. Move stm32mp15_dhsor_basic_defconfig
into stm32mp15_dhsor_basic.config. Retain stm32mp15_dhsor_basic_defconfig
as multi-config for all DH STM32MP15xx DHCOR based boards.
Introduce separate stm32mp15_dhcom_drc02_basic_defconfig,
stm32mp15_dhcom_pdk2_basic_defconfig, stm32mp15_dhcom_picoitx_basic_defconfig
for each STM32MP15xx DHCOM based board and separate
stm32mp15_dhcor_avenger96_basic_defconfig,
stm32mp15_dhcor_drc_compact_basic_defconfig,
stm32mp15_dhcor_testbench_basic_defconfig for each
STM32MP15xx DHCOR based board, to make build for those boards easier.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The environment is missing closing quotes for string variable, but the
variable is empty on this system, remove the CONFIG_BOOTCOUNT_ALTBOOTCMD
assignment entirely.
Fixes: 940135eea5 ("Kconfig: Move CONFIG_BOOTCOUNT_ALTBOOTCMD to Kconfig")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
The removal of the "st,button1" and "st,led1" compatibles has emptied
the board_late_init(), so let's remove it along with the configuration
that allows its invocation.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
It is pointless to use the custom compatible "st,led1" when
stm32746g-eval.dts and stm32f769-disco.dts already contain the
"gpio-leds" compatible, which is specifically used for GPIO LEDs
management.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
It is pointless to use the custom compatible "st,button1" when
stm32746g-eval.dts and stm32f769-disco.dts already contain the
"gpio-keys" compatible, which is specifically used for button
management.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
LDO2 is expansion connector supply on STM32MP13xx DHCOR DHSBC rev.200.
LDO5 is carrier board supply on STM32MP13xx DHCOR DHSBC rev.200. Keep
both regulators always enabled to make sure both the carrier board and
the expansion connector is always powered on and supplied with correct
voltage.
Describe ST33TPHF2XSPI TPM 2.0 chip reset lines.
This is a port of Linux kernel patch posted at:
https://patchwork.kernel.org/project/linux-arm-kernel/patch/20250302152605.54792-1-marex@denx.de/
This change shall be removed when the Linux kernel DT change lands
and Linux kernel DTs get synchronized with U-Boot DTs.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
On STM32MP15xx with 1 GiB of DRAM, the gd->ram_top becomes 0,
because DRAM base 0xc0000000 + DRAM size 0x40000000 leads to
gd->ram_top overflow which resets it to 0. Handle this special
case simply by checking for gd->ram_top being zero, and if it
is, assume there is no addr >= gd->ram_top .
This fixes boot hang on STM32MP15xx with 1 GiB of DRAM.
Fixes: 25fb58e88a ("ARM: stm32mp: Fix dram_bank_mmu_setup() for LMB located above ram_top")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
CONFIG_SYS_FDT_PAD defines the number of unused bytes added to a
device-tree and not the total size.
Fixes: 40ed7be4af ("Convert CONFIG_SYS_FDT_PAD to Kconfig")
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Structure jmp_buf_data provides the underlying format of jmp_buf, which
we actually don't care about. Clean up existing code to use the standard
jmp_buf type. This introduces no functional change.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Jerome Forissier <jerome.forissier@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Separate setjmp.h into an architecture independent part and an architecture
specific part. This simplifies moving from using struct jmp_buf_data
directly to using type jmp_buf in our code which is the C compliant way.
Reviewed-by: Jerome Forissier <jerome.forissier@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add support for multiple efi_net_obj structs in efi_net.c. This comes
in preparation for an EFI network driver supporting multiple network
interfaces. For now the EFI network stack still registers a single ethernet
udevice as an EFI network device even if multiple are present, namely
the one that was the current device at the moment of EFI initialization.
Signed-off-by: Adriano Cordova <adriano.cordova@canonical.com>
In preparation to support mutiple efi net udevices. Add a device path
cache to support device paths from multiple ethernet udevices.
The device paths can be added to the cache before EFI gets initialized and
the protocols get installed.
Signed-off-by: Adriano Cordova <adriano.cordova@canonical.com>
In preparation to support multiple EFI net objects, support
constructing device paths using an ethernet device different
than the default. Add a udevice argument to the device path
generation, and keep the callsites with eth_get_dev() to
preserve existing functionality.
Signed-off-by: Adriano Cordova <adriano.cordova@canonical.com>
This gets called each time a payload is to get executed by bootefi.
For now this only updates the PXE IP address.
Signed-off-by: Adriano Cordova <adriano.cordova@canonical.com>
The coomand bootefi calls efi_init_obj_list to do the efi set up
before launching an .efi payload, but efi_init_obj_list is called
only once. There are some initializations which depend on the
environment and should be done each time a payload gets launched and
not only once. A motivation for this changes is the following order
of events:
1. Launch an EFI application (e.g. bootefi hello)
2. Change the ip address
3. Launch another application which uses the pxe protocol
As the EFI pxe protocol was initialized when the handles
for efi net were created in 1., the ip was hardcoded there.
In this example, another possibility would be to make a callback for ip
address changes to go all the way up to efi_net.
Signed-off-by: Adriano Cordova <adriano.cordova@canonical.com>
The following symbols are exposed:
- efi_reinstall_protocol_interface
This is done so that the device path protocol interface
of the network device can be changed internally by u-boot
when a new bootfile gets downloaded.
- eth_set_dev
To support multiple network udevices
- efi_close_event
This comes in preparation to support unregistering
an EFI network device from the EFI network stack when
the underlying U-boot device gets removed
- efi_[dis]connect_controller
The EFI network driver uses ConnectController to add a
NIC to the EFI network stack.
- efi_uninstall_protocol_interface
connect_controler for the efi network driver can install
protocols, which need to be uninstalled in disconnect_controller
- EFI_SIMPLE_NETWORK_PROTOCOL_GUID
Signed-off-by: Adriano Cordova <adriano.cordova@canonical.com>
Check wget_info->buffer_size for overflow and do not clean the wget_info struct
on failure, let the owner of the struct handle the error. The latter is necesary
, e.g., for when a request fails because the provided buffer was too small.
Signed-off-by: Adriano Cordova <adriano.cordova@canonical.com>
This commit fixes an use after free introduced in Commit e55a4acb54
(" efi_loader: net: set EFI bootdevice device path to HTTP when loaded
from wget"). The logic in efi_net_set_dp is reworked so that when the
function is invoked it not only changes the value of the static variable
net_dp (this is how the function was implemented in e55a4acb54) but also
updates the protocol interface of the device path protocol in case efi
has started.
Fixes: e55a4acb54 ("efi_loader: net: set EFI bootdevice device path to HTTP when loaded from wget")
Signed-off-by: Adriano Cordova <adriano.cordova@canonical.com>
Add a simple and transparent LVDS de/encoder driver with a powerdown
gpio and a power supply.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Hide video bridge functions behind config condition and add inline
fallbacks to avoid erroring out when using header without config
enabled.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
