For TH1520, we want clock and pinctrl drivers to bind before relocation
along with the UART which makes use of them, since upstream devicetree
specifies pinctrl properties for the UART.
This requires a large malloc pool before relocation, let's enlarge it.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The ARM64 kernel Image size with LOCKDEP enabled is now around 80 MiB, which
makes it unbootable due to "Image too large: increase CONFIG_SYS_BOOTM_LEN".
Increase the image size limit to 128 MiB to future proof the limit.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The MediaTek MT7987/MT7988 SoCs features a built-in 2.5Gb PHY
connected to GMAC1. The PHY supports 10/100/1000/2500 Mbps
full-duplex only.
The PHY requires one or two firmware files. Firmware for MT7988 has
already been added to upstream: mediatek/mt7988/i2p5ge-phy-pmb.bin.
MT7987 has two firmware files which will be add to upstream later:
i2p5ge-phy-pmb.bin and i2p5ge-phy-DSPBitTb.bin.
Environment variable can be set for firmware data loading:
mt7987_i2p5ge_load_pmb_firmware for i2p5ge-phy-pmb.bin
mt7987_i2p5ge_load_dspbit_firmware for i2p5ge-phy-DSPBitTb.bin
mt7988_i2p5ge_load_pmb_firmware for i2p5ge-phy-pmb.bin
This driver allows dedicated weak functions to be overridden by
board to provide the firmware data:
mt7987_i2p5ge_get_fw() for MT7987
mt7988_i2p5ge_get_fw() for MT7988
To enable the PHY, add the following not to device tree:
ð1 {
status = "okay";
phy-mode = "xgmii";
phy-handle = <&phy15>;
phy15: ethernet-phy@15 {
compatible = "ethernet-phy-ieee802.3-c45";
reg = <15>;
phy-mode = "xgmii";
};
};
Signed-off-by: Sky Huang <SkyLake.Huang@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Associate PHY device with its device node specified by phy-handle
property. This makes it possible for PHY drivers to read dedicated
information to configure the PHY device.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
It's important to return the actual firmware data size as some
firmware files may have no checksum and need the size as the only
way for firmware validation check.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Octo Memory Manager driver (OMM) manages:
- the muxing between 2 OSPI busses and 2 output ports.
There are 4 possible muxing configurations:
- direct mode (no multiplexing): OSPI1 output is on port 1 and OSPI2
output is on port 2
- OSPI1 and OSPI2 are multiplexed over the same output port 1
- swapped mode (no multiplexing), OSPI1 output is on port 2,
OSPI2 output is on port 1
- OSPI1 and OSPI2 are multiplexed over the same output port 2
- the split of the memory area shared between the 2 OSPI instances.
- chip select selection override.
- the time between 2 transactions in multiplexed mode.
- check firewall access.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Fix RIFSC semaphores acquisition by not returning an error when the
current CID already possess the semaphore. Also fix an incorrect mask
for the CID value in the SEMCR register.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The isprint() checks printability across all 256 characters, some of the
upper 128 characters are printable and produce artifacts on UART. Call
isascii() first to only consider the bottom 7bit ASCII characters as
printable, and then check their printability using isprint(). This fixes
a rare misprint in case the ID page content is uninitialized or corrupted.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
The eip pointer in dh_get_value_from_eeprom_buffer() might be NULL.
The current NULL pointer check happens too late, after the eip was
accessed in variable assignment. Reorder the two, so the NULL pointer
check happens first, and any access second, otherwise the access may
trigger a hang or other undefined behavior.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Add the HBMC and MUX_MMIO configs in the R5 SPL stage for
successful HBMC boot.
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
MUX_MMIO is needed by HBMC in SPL stage. Enable it at SPL as well
as u-boot proper stage.
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
The commit 210702ae6c ("spl: spi: fix falcon mode for spi boot") fixed
the logic of spl_start_uboot() where 0 means OS boot and 1 means u-boot.
Zynq/ZynqMP enable OS_BOOT by default but it was never really be used
that's why disable it to boot via U-Boot phase all the time.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Commit 649f4a7d3c ("board: ti: am57xx: Set fdtfile from C code
instead of findfdt script") prepends "ti/omap/" to the actual name
of the fdtfile whereas fit image boot needs exact dtb name. So, remove
"ti/omap" from name_fit_config by substituting it with an empty string.
Fixes: 649f4a7d3c ("board: ti: am57xx: Set fdtfile from C code instead of findfdt script")
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
This patch is used to restore support for i.MX95 A0 silicon. To avoid
duplicating defconfig, imx95.config is added and can be shared between
imx95_a0_19x19_evk_defconfig and imx95_19x19_evk_defconfig.
container.cfg and imximage.cfg are used to created .cfgout files that
are be passed to mkimage with -n to build flash.bin. Now they have been
deleted and replaced by adding their content to properties of node which
type is nxp-imx9image under binman node.
Fixes: 9936724aa9 ("imx95_evk: Add i.MX95 B0 support")
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Tested-By: Tim Harvey <tharvey@gateworks.com> # imx95-19x19-evk (rA0)
To support passing specific commands defined in enum imx8image_cmd to
the imx8image_copy_image() function, this patch introduces a new entry
type nxp-imx9image. This entry generates a plain text data file
containing the relevant commands, enabling flexible configuration during
image creation.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
The isprint() checks printability across all 256 characters, some of the
upper 128 characters are printable and produce artifacts on UART. Call
isascii() first to only consider the bottom 7bit ASCII characters as
printable, and then check their printability using isprint(). This fixes
a rare misprint in case the ID page content is uninitialized or corrupted.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
The eip pointer in dh_get_value_from_eeprom_buffer() might be NULL.
The current NULL pointer check happens too late, after the eip was
accessed in variable assignment. Reorder the two, so the NULL pointer
check happens first, and any access second, otherwise the access may
trigger a hang or other undefined behavior.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
In case the PHY exit callback reports failure, reset init_count to 0 anyway,
so the next attempt at PHY initialization might try to reinitialize the PHY
and restore it to normal operation.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Make sandbox_thermal_get_temp() static, since this is not called
outside of the driver. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The U-Boot coding style guide has been updated to include information
about using the `.clang-format` configuration file for automatic code
formatting. This ensures consistent formatting across the entire
codebase and aligns with Linux kernel coding standards. The goal with
introducing a predefined coding style is consistency rather than
personal preference.
The .clang-format file is copied directly from the Linux kernel without
any modifications, ensuring complete compatibility with kernel coding
standards.
Include comprehensive best practices for using clang-format,
specifically guidance on formatting only changed blocks versus entire
files, creating separate formatting-only commits for better code review,
and leveraging git clang-format for targeted formatting. Add examples of
editor integrations. This enhancement will help maintainers and
contributors to easily adhere to U-Boot coding standards.
Signed-off-by: Javier Tia <javier.tia@linaro.org>
The Linux kernel has not maintained the same script since 2017-11-01,
and with clang-format included in U-Boot, it is not required anymore.
Signed-off-by: Javier Tia <javier.tia@linaro.org>
Replace the use of scripts/Lindent with clang-format in
zynqmp_psu_init_minimize.sh. This change is made to align with the rest
of the codebase that uses clang-format for code formatting. This ensures
consistency across all scripts in terms of code style and formatting.
Tested-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Javier Tia <javier.tia@linaro.org>
Introduce .clang-format configuration file to U-Boot, providing
significant improvements over the existing scripts/Lindent approach for
C code formatting.
Benefits of clang-format over scripts/Lindent:
- More comprehensive formatting rules: While Lindent relies on the basic
'indent' tool with limited options, clang-format provides extensive
control over code formatting with 800+ configuration options
- Better handling of complex code structures: clang-format understands
modern C constructs and handles nested structures, macros, and complex
expressions more intelligently
- IDE and editor integration: Native support in major development
environments (VS Code, Vim, Emacs, etc.) enables real-time formatting
- Consistent results across environments: Eliminates variations between
different versions of 'indent' tool and system configurations
- Active maintenance: clang-format is actively developed and updated,
unlike the aging 'indent' tool
Alignment with Linux kernel practices:
Continues U-Boot alignment with Linux kernel development practices,
maintaining consistency between these closely related projects. The
Linux kernel adopted clang-format to modernize its code formatting
infrastructure and improve developer experience.
The .clang-format file is based on the Linux kernel configuration,
specifically copied from Linux kernel v6.16 tag, which itself builds
upon the initial introduction in commit d4ef8d3ff005c ("clang-format:
add configuration file").
Signed-off-by: Javier Tia <javier.tia@linaro.org>
Greg Malysa <malysagreg@gmail.com> says:
Between 2025.07 and 2025.10 many header dependency chains were improved,
but this exposed implicit header usage in several of our drivers. This
wasn't discovered before or included in the original fixes because our
drivers are not yet used by any mainline-supported boards, so build
tests did not find them. This series addresses the two build failures
I've encountered while rebasing our work onto 2025.10 and continuing to
prepare the next submission of our board files.
Link: https://lore.kernel.org/r/20250903234205.26787-1-malysagreg@gmail.com
As part of the header dependency cleanup between 2025.07 and 2025.10, an
implicit route to obtain SZ_128M from linux/sizes.h was removed. This
adds an explicit reference to linux/sizes.h to fix build failures for
this driver.
Signed-off-by: Greg Malysa <malysagreg@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Following header dependency cleanups, an implicit dependence on env.h
was exposed in dwc_eth_qos_adi. However because this driver is not (yet)
enabled in any defconfigs, build tests did not identify the missing
header. This adds the missing #include so that the driver builds
correctly when enabled.
Signed-off-by: Greg Malysa <malysagreg@gmail.com>
serial_reinit_all() is only available when CONFIG DM_SERIAL is disabled
and CONFIG_SERIAL is enabled.
Signed-off-by: Aditya Dutt <duttaditya18@gmail.com>
The ADP5587 is a simpler version of the ADP5588. The ADP5588 can
configure two pins, C8 and C9, as GPIOs or light sensors. The ADP5587
does not include the light sensors.
Signed-off-by: Philip Molloy <philip@philipmolloy.com>
The CONFIG_ENV_VARS_UBOOT_CONFIG should protect only U-Boot
configuration variables in environment, those are arch, cpu,
board, board_name, vendor, soc. It should certainly not hide
usb_ignorelist or env_fdt_path from the environment. Fix it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Check the compatible string of ethernet1 node for KS8851 very early on,
before calling uclass_get_device_by_of_path() which might initialize
the device and possibly attempt to configure MAC address into device
which is not KS8851. Doing the compatibility check early prevent this.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The layout of SYSCFG_ETHnCR on STM32MP25xx is slightly different yet again.
Add missing swizzling to program the correct register with the correct content.
Fixes: 20afca89ed ("net: dwc_eth_qos: add support of stm32mp2 platform")
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Christophe ROULLIER<christophe.roullier@foss.st.com>
