Enable LTO globally on Renesas R-Car platforms. This has been enabled
on a subset of boards already, but at this point it is safe to enable
it globally. This saves units or tens of kiB from the resulting build.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Xilinx changes for v2024.04-rc3
zynqmp:
- Cover missing _SE chip variants to fix fpga programming
versal:
- Enable LTO for mini configurations
versal-net:
- Enable LTO for mini configurations
- Fix GIC address to aligned with real silicon
xilinx:
- DTs cleanup and fixups
- Enable HTTP boot
- Add missing spl header to zynqmp.c
Board description describes the hard part of chip (PS) but programmable
logic (PL) part is not described in this file. But clocks on the board are
not only connected to PS but also wired to PL. And because two revisions
are available where revA is using one si5332 and revB multiple clock chips
using the same clock labels helping with keeping only one device tree
overlay which targets PL. That's why synchronize clock labels and use
labels from revB which are more generic.
Unfortunately if there is driver for si5332 chip split could happen again
but it is still worth to do it now and solve this issue when occurs.
Reported-by: Sagar Karmarkar <sagar.karmarkar@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/abac6069e6029ed4076ec7b9d6b33604b6072aa3.1706253871.git.michal.simek@amd.com
Without 'silabs,skip-recall' property, the driver on System Controller
re-calibrates the output clock frequency at probe() time based on the NVRAM
setting. This re-calibration causes a glitch on the output clock. At
power-on, Versal is also booting and expecting a glitch-free clock for
its correct operation. System Controller should skip the re-calibration
step to prevent any clock instability for Versal.
Signed-off-by: Saeed Nowshadi <saeed.nowshadi@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/bbb2322c94503f0e6b369c60312b7546500fad95.1706170068.git.michal.simek@amd.com
The SPL clock code does configure the ECSPI clock frequency, which has
to match the mxc-spi driver configuration for successful SPI NOR boot.
Drop the assigned-clock from DT ecspi1 node on this board to let the
SPL clock code do the configuration and keep it aligned with the driver
expectation.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add Renesas R8A779H0 V4M DT extras for U-Boot.
Until the RPC node becomes part of main DT, keep it here as
an extension so that board code can enable and use the RPC
to access SPI NOR.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
These select/imply settings are common to the whole architecture not just
these boards, move these settings to the architecture config.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
TI KS2 boards have the nfs command in their common environment boot
configuration, enable this command.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
- Add USB support for phycore-imx8mp
- Fix environment corruption, reset on mx6sabresd
- Print reset cause on imx8
- Extend mkimage to support generating an image for i.MXRT FlexSPI
- Add new apalis and colibri variants
- Add support for phyBOARD-Segin-i.MX93 support
- Fix when FEC is primarily used instead of EQOS on i.MX93.
Commit 68dcbdd594 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Commit d5eae216d8 ("net: dwc_eth_qos: Add board_interface_eth_init()
for i.MX93") implemented board_interface_eth_init for i.MX9 platforms.
However it only accounted for the EQOS interface while any board using
FEC as primary Ethernet interface was left out as return value -EINVAL
is always returned from the function in such case.
Fix this by returning 0 (success) when FEC interface is primarily used
instead of EQOS interface on i.MX93.
Fixes: d5eae216d8 ("net: dwc_eth_qos: Add board_interface_eth_init() for i.MX93")
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Tested-by: Mathieu Othacehe <m.othacehe@gmail.com>
When an XXX_BOOTCOMMAND isn't defined, the result is that bootcmd is set
to some random memory content. Fix it so that the function does nothing
in that case and leaves the bootcmd environment unmodified.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
The number of DDR controllers to be initialised and used should depend
on the device tree with the constraint of the maximum number of
controllers the device supports. Since J721S2 has multiple (2)
controllers, instead of hardcoding the number of probes, move to
depending on the device tree UCLASS_RAM nodes present.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
This commit enables support for DM_SERIAL in the vexpress_ca9x4 boards.
When running the board with the DM_SERIAL driver, the board ran out of
memory in SPL when initialising the DM serial driver.
Thus this required an increase in the pre-allocated SRAM memory. I did
increase it to 0x800, and it now works graciously.
It could probably be set lower, but I do not see any reason not to use the
available SRAM at this point.
Also adds stdout-path to the 'chosen' node in the device tree.
Signed-off-by: Ole P. Orhagen <ole.orhagen@northern.tech>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Writing to eMMC using HS200 mode work more reliably then other modes on
RK356x boards.
Add device tree props and enable Kconfig options for eMMC HS200 mode on
the generic RK3566/RK3568 board. Also enable the pinctrl driver in SPL
and add missing rk3568-generic.dtb to Makefile.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Testing has shown that writing to eMMC using a slower mode then HS200
typically generate an ERROR on first attempt on RK3588.
# Rescan using MMC legacy mode
=> mmc rescan 0
# Write a single block to sector 0x4000 fails with ERROR
=> mmc write 20000000 4000 1
# Write a single block to sector 0x4000 now works
=> mmc write 20000000 4000 1
With the MMC_SPEED_MODE_SET Kconfig option enabled.
Writing to eMMC using HS200 mode work more reliably than slower modes on
RK35xx boards. Enable MMC_HS200_SUPPORT Kconfig option by default to
prefer use of HS200 mode on RK356x and RK3588.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Testing has shown that writing to eMMC using DDR52 mode does not seem to
work on RK356x and RK3588 boards.
A simple test of writing a single block to e.g. sector 0x4000 fails:
# Rescan using DDR52 mode
=> mmc rescan 4
# Write a single block to sector 0x4000 fails with ERROR
=> mmc write 20000000 4000 1
With the MMC_SPEED_MODE_SET Kconfig option enabled.
Fix this by removing the mmc-ddr-1_8v prop from sdhci nodes in affected
board u-boot.dtsi files.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove unnecessary status props from rk35xx u-boot.dtsi files, regular
device tree files or default value already enable the affected nodes.
Also reorder bootph-pre-ram and clock-frequency props alphabetically in
rk3588s-u-boot.dtsi uart2 node.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a default u-boot,spl-boot-order prop to rk3588s-u-boot.dtsi and
remove the prop from board u-boot.dtsi files using the default value.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3588 device tree from linux v6.7.
Also drop the rockchip,rk3568-dwc3 compatible now that dwc3-generic
driver support the rockchip,rk3588-dwc3 compatible.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Move uart2 bootph-pre-ram and clock-frequency props from board to SoC
u-boot.dtsi. Regular board device tree already enables the uart2 node,
so status prop is dropped from u-boot.dtsi file.
Also remove unnecessary stdout-path = &uart2, regular board device tree
already provide a stdout-path = "serial2:" value.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip RK3399 and RK3588 SoCs can support wide range of bootflows.
Without full bootflow commands, it can be difficult to
figure out issues if any, hence enable by default.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Shantur Rathore <i@shantur.com>
rv1126 requires OPTEE as it provides pcsi support. Mainline Linux
kernel will fail to boot without this.
Select SPL_OPTEE_IMAGE when building FIT image. TEE must be provided
when building.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sonoff iHost is gateway device designed to provide a Smart Home Hub,
it is based on Rockchip RV1126. There is also a version with 2GB RAM
based off the RV1109 dual core SoC however this works with the same
config as the RV1126 for uboot purposes.
Features:
- Rockchip RV1126
- 4GB DDR4
- 8GB eMMC
- microSD slot
- RMII Ethernet PHY
- 1x USB 2.0 Host
- 1x USB 2.0 OTG
- Realtek RTL8723DS WiFi/BT
- EFR32MG21 Silabs Zigbee radio
- Speaker/Microphone
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync linux dts files for rv1126 boards from linux v6.8-rc1 tag. Includes
the newly added dts for Sonoff iHost.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
