For some JH7110 boards, USB host overcurent pin is not reserved,
To make USB host work, overcurrent pin must be disabled. So set the
pin default disabled in spl stage.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Tested-by: E Shattow <lucent@gmail.com>
Update rm-cfg.yaml and tifs-rm-cfg.yaml to account for the
changes added in the K3 Resource Partitioning Tool v1.18
The change enables resource sharing between A72_2 and MAIN_0_R5_0
for the BCDMA CSI RX and TX channels, J784S4 supports upto 12
CSI cameras and 16 channels would not be enough for all such use
cases for RTOS and Linux, thus sharing of resources in needed. Resource
sharing between A72 and R5 for BCDMA CSI channels allow Linux to use 32
channels at a time.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
[n-francis@ti.com: rebased and sent on behalf]
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Apalis/Colibri iMX6 V1.2 will replace the STMPE811 ADC/Touch controller
which is EOL by the TLA2024 ADC and AD7879 touch controller.
To support this new version, we detect the presence of the TLA2024
during boot and set a new environment variable named "variant". This
will allow us and users to select the correct DT easily.
By probing via I2C we have a robust detection method instead of relying
on the existing "board_rev" environment variable which is set by the
config block. Users can use "variant" in their DT selection and do not
have to map the board revision to a device tree.
"variant" environment variable behaviour:
* Empty or absent for all versions below v1.2 (STMPE811)
* "-v1.2" for all versions starting from v1.2 (TLA2024 + AD7879)
Usage example:
setenv fdtfile imx6q-apalis${variant}-${fdt_board}.dtb
Signed-off-by: Ernest Van Hoecke <ernest.vanhoecke@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Updates for RPi for 2025.04:
- Copy Bluetooth device address in DT
- Keep warnings from firmware in DT, if any
- Only add frame buffer node if CONFIG_FDT_SIMPLEFB is set
- Add identifiers for the new RPi 5 series
The firmware sets local-bd-address, copy it when loading a new DT.
Signed-off-by: Fiona Klute <fiona.klute@gmx.de>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
The /chosen/user-warnings property is created by the RPi firmware if
there are warnings to report, keep it to make debugging easier.
For example, if the firmware config.txt contains
"dtoverlay=error-example" and that example references an undefined
symbol "&nosuchdev" the warning can be read after boot:
$ cat /proc/device-tree/chosen/user-warnings
dterror: can't find symbol 'nosuchdev'
Failed to resolve overlay 'error-example'
Signed-off-by: Fiona Klute <fiona.klute@gmx.de>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
The functions fdt_simplefb_add_node and fdt_simplefb_enable_and_mem_rsv
are only available if CONFIG_FDT_SIMPLEFB is enabled.
Signed-off-by: Martin Stolpe <martin.stolpe@gmail.com>
Acked-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
The Raspberry Pi foundation have released the Raspberry
Pi 500, CM5 an CM5 lite devices so add the assoicated
revision identifers so we can detect them.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Matthias Brugger <mbrugger@suse.com>
CI: https://source.denx.de/u-boot/custodians/u-boot-stm/-/pipelines/25112
- Add drivers for MFD STM32 TIMERS and STM32 PWM and enable them on stm32mp135f-dk
- Restrict _debug_uart_init() usage in STM32 serial driver
- Add support for environment in eMMC on STM32MP13xx DHCOR SoM
- Introduce DH STM32MP15xx DHSOM board specific defconfigs
- Fix CONFIG_BOOTCOUNT_ALTBOOTCMD update on DH STM32MP1 DHSOM
- Update maintainer for board stm32f746-disco
- Fix Linux cmdline for stm32f769-disco
- Cleanup in stm32f***-u-boot.dtsi and in board_late_init() by removing
legacy led and button management.
The default PCA9451 BUCK2 volt is 0.6 V for LPDDR4x VDDQ. The codes
are actually used for reworking to LPDDR4 which needs VDDQ at 1.1 V.
So remove it to avoid LPDDR4x issue.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Enable PCI enumeration by default to get the Bochs display driver up
and running before the boot medium is scanned.
This is just to enhance the user-experience while booting the machine.
TEST: U-Boot logo, version, log output and the U-Boot shell is visible
on the display device.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
qemu's sbsa-ref is always using a 64bit CPU and the PCI prefetch MMIO
window is located above 4GiB, thus always enable SYS_PCI_64BIT.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Vikas has left STMicroelectronics several years ago.
Put myself as maintainer of stm32f746-disco board.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Use mdio_alloc() again to allocate MDIO bus. This is possible
because all the miiphybb parameters and ops passing is handled in
at bb_miiphy_read()/bb_miiphy_write() level.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Remove the priv member from struct bb_miiphy_bus and its assignment
from drivers. This turns struct bb_miiphy_bus int struct mii_dev
wrapper, to be cleaned up next.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Access to MDIO bus private data can be provided by both
struct mii_dev .priv member and struct bb_miiphy_bus .priv
member, use the former directly and remove .priv from the
later. Drop unused bb_miiphy_getbus(). This removes any
dependency on struct bb_miiphy_bus from the miiphybb code,
except for helper functions which will be removed later.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
The access to struct bb_miiphy_bus_ops via ops pointer in
struct bb_miiphy_bus is not necessary with wrappers added
in previous patch. Pass the ops pointer directly to both
bb_miiphy_read() and bb_miiphy_write() functions.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Do not call bb_miiphy_read()/bb_miiphy_write() accessors directly
in drivers, instead call them through wrapper functions. Those are
meant to be used as function parameter adaptation layer between
struct mii_dev callback function parameters and what the miiphybb
does expect and will soon expect. This is a preparatory patch, no
functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Move miiphybb operations into separate struct bb_miiphy_bus_ops
structure, add pointer to struct bb_miiphy_bus_ops into the base
struct bb_miiphy_bus and access the ops through this pointer in
miiphybb generic code. The variable reshuffling in miiphybb.c
cannot be easily avoided.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
The Mi Pad is a tablet computer based on Nvidia Tegra K1 SoC which
originally ran the Android operating system. The Mi Pad has a 7.9" IPS
display with 1536 x 2048 (324 ppi) resolution. 2 GB of RAM and 16/64 GB of
internal memory that can be supplemented with a microSDXC card giving up to
128 GB of additional storage.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The removal of the "st,button1" and "st,led1" compatibles has emptied
the board_late_init(), so let's remove it along with the configuration
that allows its invocation.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
It is pointless to use the custom compatible "st,led1" when
stm32746g-eval.dts and stm32f769-disco.dts already contain the
"gpio-leds" compatible, which is specifically used for GPIO LEDs
management.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
It is pointless to use the custom compatible "st,button1" when
stm32746g-eval.dts and stm32f769-disco.dts already contain the
"gpio-keys" compatible, which is specifically used for button
management.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
AMD/Xilinx changes for v2025.04-rc4
Zynq:
- Guard code around SPL_FS_LOAD_PAYLOAD_NAME
Versal*:
- Remove tftp block size 4096
Versal:
- Use clocks per DT binding
- Store driver data in data section
Versal Gen 2:
- Fix major/minor version decoding
The commit bc07851897 ("board: ti: Pull redundant DDR functions to a
common location and Fixup DDR size when ECC is enabled") broke DRAM
support for the Verdin AM62. This was partially fixed with commit
3f866c47b5 ("board: verdin-am62: add dram_init_banksize"). However,
because fixup_memory_node was not called, the Linux kernel was started
with the wrong memory size on modules with less memory available. This
resulted in boot failures. Fix this issue by calling fixup_memory_node
in the board file.
spl_perform_fixups will be called in the SPL and now sets the correct
memory size in the device tree of U-Boot by calling fixup_memory_node.
U-Boot will then adjust the memory sizes of Linux during bootm/booti in
fdt_fixup_memory_banks. This chain ensures that U-Boot and Linux only
use RAM that is actually available.
Fixes: 3f866c47b5 ("board: verdin-am62: add dram_init_banksize")
Fixes: bc07851897 ("board: ti: Pull redundant DDR functions to a common location and Fixup DDR size when ECC is enabled")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Fix build error "undefined reference to `is_warm_boot'" when
ls1021atsn and ls1021atwr boards are built with CONFIG_SPL=y and
CONFIG_DEEP_SLEEP=n.
Signed-off-by: Benjamin Lemouzy <blemouzy@centralp.fr>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Baocheng Su <baocheng.su@siemens.com> says:
This introduces a sysinfo driver which also permits SMBIOS support.
The first 10 patches of v2 have already been applied. The remaining is
solely the sysinfo driver. To maintain consistency and ease of searching
through the history, the series title remains unchanged.
Link: https://lore.kernel.org/r/20250218023614.52574-1-baocheng.su@siemens.com
Drop the info structure parsing of the board in favor of our new sysinfo
driver to avoid code duplication.
Signed-off-by: Baocheng Su <baocheng.su@siemens.com>
Signed-off-by: Li Hua Qian <huaqian.li@siemens.com>
[Jan: rebasing, split-up, cleanup]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/24876
- Convert imx6q-lxr and imxrt1050 to OF_UPSTREAM.
- Fix potential memory leak on ]imx/imx8/imx8m]image.
- Restrict DDR_SI_TEST to only Siemens Capricorn board.
- Fix CONFIG_BOOTCOUNT_ALTBOOTCMD on Data Modul and DH imx8m boards.
The DDR_SI_TEST config option is only relevant to the i.MX8 Capricorn
board.
Make DDR_SI_TEST depend on DDR_SI_TEST so that it does not show up
on other targets.
Signed-off-by: Liya Huang <1425075683@qq.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Currently, booting via bootstd fails because the kernel cannot be retrieved.
The reason for this is the lack of 'kernel_addr_r'.
Pass 'kernel_addr_r' to fix booting via bootstd.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Currently, booting via bootstd fails because the kernel cannot be retrieved.
The reason for this is the lack of 'kernel_addr_r'.
Pass 'kernel_addr_r' to fix booting via bootstd.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Instead of doing another lookup, trivially access the struct mii_dev
embedded in struct bb_miiphy_bus . No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
The struct bb_miiphy_bus embeds struct struct mii_dev, which
already contains one copy of name field. Drop the duplicate
top level copy of name field.
The a38x code does static assignment of disparate names, use
snprintf(...) to fill in matching name in probe to avoid any
breakage.
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Allocate bb_miiphy using bb_miiphy_alloc() and fill in callbacks
currently listed in bb_miiphy_buses[] array. This is a temporary
duplication of assignment to avoid breakage, which will be removed
in follow up patches. At this point, the bb_miiphy callbacks can
reach these accessors by doing container_of() on struct mii_dev.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
All the resources needed by this .init callback should already
be available by the time probe function runs, simply call the
init callback directly and set the bb_miiphy init callback to
NULL. This shouldn't break anything on this hardware, but would
be nice if someone could double-check and test that.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Move the bb_miiphy functions before MDIO registration. This is a
preparatory patch, the functions will be referenced around the MDIO
registration in the follow up patches. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
CI: https://source.denx.de/u-boot/custodians/u-boot-socfpga/-/pipelines/24816
Please pull the SoCFPGA changes for next from u-boot-socfpga, containing
boot support for the Altera SoCFPGA Agilex 5 platform in U-Boot. The
changes include:
1. Board-specific configurations and setup required to enable Agilex 5
operation in U-Boot.
2. Integration of cache coherency unit (CCU) initialization routine,
including CCU conguration in DT.
3. Clock, firewall (configured in DT), SMMU, low level initialization
specific to Agilex 5.
4. Integration of memory initialization routine, including DDR setup.
This patch set has been tested on Agilex 5 devkit with QSPI boot
(UBI/UBIFS) and RAM boot (TFTP & ARM DS debugger).
Initial creation of new system manager driver.
Add supports for the SOCFPGA System Manager Register block which
aggregates different peripheral function into one area.
On 64 bit ARM parts, the system manager only can be accessed during
EL3 mode, this driver model provide user the high level access
to system register and abstract user from low level access.
The base address of system manager can be retrieved
using DT framework through the System Manager driver.
Signed-off-by: Tien Fong Chee <tien.fong.chee@altera.com>
Signed-off-by: Boon Khai Ng <boon.khai.ng@altera.com>
Branch contains bringup of Acer Iconia Tab A500 (codename picasso), a
Tegra 2 Android device with decent Linux kernel support. Ondevice tests
and U-Boot test suit all passed.
