- spi: stm32: OSPI and QSPI optimization
- Update stm32 clock drivers to restore boot for STM32MP13/STM32MP2
board family
- Add bootph-all in ltdc node in stm32mp257f-ev1-u-boot
- Use CONFIG_STM32MP15X to discern STM32MP15xx on DH STM32MP15xx DHSOM
- Reinstate missing SPL configs for DH STM32MP15xx DHSOM
- stm32mp2 boards: read boot index from backup register
- video: simple_panel: add support for "rocktech,rk043fn48h" display
- Add .of_to_plat callback in stm32_ltdc driver
This symbol is used on a number of PowerPC platforms as well, so make it
available there again.
Fixes: 424b324165 ("armv7: Add CPLD support via IFC to the ls1021a-iot board.")
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Drivers should extract device-tree data before probing via the
.of_to_plat hook.
Implement it for stm32_ltdc driver. No functional change.
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
During clock's registration, clock's name are used to establish parent -
child relation. On STM32MP13 and STM32MP25, most of SCMI clocks are parent
clocks.
Since commit fdb1bffe28 ("clk: scmi: Postpone clock name resolution"),
all scmi clocks are named by default "scmi-%zu" until they are enabled,
it breaks clocks registration and boot process for STM32MP13/25
platforms.
Rework the STM32 core clock driver and STM32MP13/25 clock description
to use clock index instead of their real name.
Introduce struct clk_parent_data which allows to identify parent clock
either by index or by name. Name is only used for particular clocks
provided by IP which are clock provider as i2s/i2s_ckin, usb0/ck_usbo_48m,
and ltdc/ck_ker_ltdc.
STM32_GATE() and STM32_COMPOSITE_NOMUX macros are updated in order to
use parent clock index.
As STM32MP13 supports both SPL and SCMI boot, keep using an array
with clock's name for SPL.
Fixes: fdb1bffe28 ("clk: scmi: Postpone clock name resolution")
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
FIFO accesses uses u8 only for read/write.
In order to optimize throughput, add u16 or u32 read/write
accesses when possible.
Set FIFO threshold level value accordingly.
Test performed by writing and reading 64MB on sNOR on
stm32mp157c-ev1 board:
before after ratio
Write : 428 KB/s 719 KB/s +68%
Read : 520 KB/s 3200 KB/s +615%
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
When WATCHDOG_RESET() was replaced by schedule() in commit
29caf9305b ("cyclic: Use schedule() instead of WATCHDOG_RESET()")
we not only reset the watchdog but also call the cyclic infrastructure
which takes time and has impact on read accesses performances.
Move schedule() from _stm32_qspi_read_fifo() to _stm32_qspi_poll()
and call schedule() only every 1MB chunk of data.
Test performed by reading 64MB on sNOR on stm32mp157c-ev1 board:
before after ratio
Read : 201 KB/s 520KB/s +258%
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Schedule() is called every u8/u16 or u32 read accesses which is overkill.
Move schedule() from stm32_ospi_read_fifo() to stm32_ospi_tx_poll()
and call schedule() only every 1MB chunk of data.
Test performed by reading 64MB on sNOR on stm32mp257f-ev1 board:
before after ratio
Read : 10.6MB/s 14.2MB/s +34%
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Markus Schneider-Pargmann (TI.com) <msp@baylibre.com> says:
musb currently uses a wrapper driver that binds on the parent device of
the actual musb devices to manage the differentiation between gadget and
host modes. However in the upstream devicetree this parent devicetree
node can not be used to match the wrapper driver.
To be able to probe the musb devices in host/gadget mode directly, this
series introduces support for returning -ENODEV in bind functions
resulting in iterating the remaining drivers potentially binding to
other drivers that match the compatible.
Link: https://lore.kernel.org/r/20260127-topic-musb-probing-v2026-01-v4-0-ea3201e0f809@baylibre.com
The loop in lists_bind_fdt uses an indented style for log messages
within the loop and normal messages for errors that lead to the exit of
the function. Due to the change of the previous patch that adds support
for continuation on -ENODEV returned by bind, the log message should be
indented.
Signed-off-by: Markus Schneider-Pargmann (TI) <msp@baylibre.com>
Currently once a driver matched the compatible string of a device, other
drivers are ignored. If the first matching driver returns -ENODEV, no
other possibly matching drivers are iterated with that compatible of the
device. Instead the next compatible in the list of compatibles is
selected, assuming only one driver matches one compatible at a time.
To be able to use the bind function to return -ENODEV and continue
matching other drivers with the same compatible, move the for loop a bit
to continue the for loop after -ENODEV was returned. The loop had to be
adjusted a bit to still support the 'drv' argument properly. Some
simplifications were done as well.
The modification will only add additional loop iterations if -ENODEV is
returned. Otherwise the exit and continue conditions for the loop stay
the same and do not cause any additional iterations and should not
impact performance.
This is required for ti-musb-host and ti-musb-peripheral which both
match on the same device but differ based on the dr_mode DT property.
Depending on this property, the driver is either UCLASS_USB or
UCLASS_USB_GADGET_GENERIC. By checking the DT property in the bind
function and returning -ENODEV the other driver can probe instead.
Reviewed-by: Simon Glass <simon.glass@canonical.com>
Acked-by: Dinesh Maniyam <dinesh.maniyam@altera.com>
Signed-off-by: Markus Schneider-Pargmann (TI.com) <msp@baylibre.com>
'found' is only used at the end of the function to print a debug
message. No need to maintain a variable if we can just return 0
immediately when a driver was bound successfully.
Reviewed-by: Simon Glass <simon.glass@canonical.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Signed-off-by: Markus Schneider-Pargmann (TI.com) <msp@baylibre.com>
This patch renames the board directory from board/freescale to
board/nxp because NXP now provides Board Support Packages (BSPs) and
tools for the former Freescale i.MX and other i.MX products.
All relevant references have been updated accordingly. This change does
not affect functionality.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add the descriptions for the DC/DC regulators of the AXP318W, and enable
it when CONFIG_AXP318W_POWER is enabled.
Signed-off-by: Yixun Lan <dlan@gentoo.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
The PMIC is also known as AXP819 in vendor pmu code
For DCDC6, 8, 9, the underlying hardware support more than two levels
voltage step tuning, but for now only first two levels are implemented
in this driver, hence highest voltage will be limited at seccond level.
It actual meets board requirement in current design, and we've verified
it in Radxa Cubie A7A board.
Following are detail explanation of voltage tuning stpes for those DCDCs:
DCDC | voltage range | units | steps | implemented
6 | 0.5 - 1.2 | 10 mV | 71 | Y
. | 1.22 - 1.54 | 20 mV | 17 | Y
. | 1.8 - 2.4 | 20 mV | 31 | N
. | 2.44 - 2.76 | 40 mV | 9 | N
--------------------------------------------------
8/9 | 0.5 - 1.2 | 10 mV | 71 | Y
. | 1.22 - 1.84 | 20 mV | 32 | Y
. | 1.9 - 3.4 | 100mV | 16 | N
Signed-off-by: Yixun Lan <dlan@gentoo.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
The T113-s4 SoC is using the same die as the T113-s3, but comes with
256MiB of co-packaged DRAM. Besides the doubled size, the DRAM chip
seems to be connected slightly differently, which requires to use a
different pin remapping.
Extend the DRAM initialisation code to add support for the T113-S4 aka
T113M4020DC0 by checking the SoC's CHIPID, which is stored in the first
word of the SID efuses.
Signed-off-by: Lukas Schmid <lukas.schmid@netcube.li>
Tested-by: John Watts <contact@jookia.org>
Reviewed-by: John Watts <contact@jookia.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When aborting a Transfer Descriptor (TD), the xHCI driver updates the
device dequeue pointer by converting the virtual enqueue TRB pointer
into a DMA address.
Previously, the code OR-ed the ring's Dequeue Cycle State (DCS) bit into
the virtual TRB pointer before passing it to xhci_trb_virt_to_dma().
This produced an unaligned virtual address (e.g. ending in 0x...1).
Inside xhci_trb_virt_to_dma(), the offset calculation:
segment_offset = trb - seg->trbs;
operated on this unaligned pointer, resulting in an incorrect TRB index.
In wraparound cases, this caused the bounds check to fail and the
function to return 0.
As a result, a SET_DEQ_PTR command was issued with a DMA address of 0x0,
leading to controller hangs and transfer timeouts, most commonly when
aborting TDs near the end of a ring segment (e.g. index 63).
Fix this by translating the aligned virtual TRB pointer to a DMA address
first, and only then applying the DCS bit to the resulting physical
address.
Reviewed-by: Marek Vasut <marek.vasut@mailbox.org>
Signed-off-by: ANANDHAKRISHNAN S <anandhakrishnan.s@dicortech.com>
A TrueType font for U-Boot should fulfill the following requirements:
* mono spaced
* support full code page 437
* easily readable
Unfortunately none of the fonts provided with U-Boot fulfills all of these
requirements.
Let's add the DejaVu Mono font. To reduce the code size the characters are
limited to code page 437.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In sd_get_capabilities an ACMD is sent (SD_CMD_APP_SEND_SCR),
which requires sending APP_CMD (MMC_CMD_APP_CMD) before.
Currently, the ACMD is retried on error, however APP_CMD isn't.
In this case, when the ACMD fails and it is tried again,
the retry attempts will not be handled as ACMD, which is wrong.
The fix performs the retry attempts on the sequence of
APP_CMD and the ACMD together.
Signed-off-by: Yanir Levin <yanir.levin@tandemg.com>
Reviewed-by: Eran Moshe <emoshe@gsitechnology.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Use dev_read_u32_default() instead of dev_read_u32() to read the
"max-frequency" property from device tree. This preserves the driver-set
cfg->f_max value when the optional "max-frequency" property is not
present, ensuring the controller's default frequency is used as fallback
rather than being overwritten.
Suggested-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tanmay Kathpalia <tanmay.kathpalia@altera.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
If CONFIG_DM_GPIO is not enabled, compilation fails with the following
errors:
aarch64-none-linux-gnu-ld: drivers/power/regulator/regulator_common.o: in function `regulator_common_of_to_plat':
<...>/u-boot/drivers/power/regulator/regulator_common.c:30: undefined reference to `gpio_request_by_name'
aarch64-none-linux-gnu-ld: drivers/power/regulator/regulator_common.o: in function `regulator_common_get_enable':
<...>/u-boot/drivers/power/regulator/regulator_common.c:57: undefined reference to `dm_gpio_get_value'
aarch64-none-linux-gnu-ld: drivers/power/regulator/regulator_common.o: in function `regulator_common_set_enable':
<...>/u-boot/drivers/power/regulator/regulator_common.c:92: undefined reference to `dm_gpio_set_value'
make: *** [Makefile:2029: u-boot] Error 139
Since the enable gpio is optional we can conditionally skip these calls.
Reviewed-by: Tanmay Kathpalia <tanmay.kathpalia@altera.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Replace casting with long to IS_ERR_VALUE() macro to check for error
return values from rate calculation functions. This is the recommended
way to check the return value from clock rate functions.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Replace uclass_get_device_by_ofnode() with syscon_regmap_lookup_by_phandle()
to get the "mediatek,pctl-regmap" syscon device.
Depending on probe order, uclass_get_device_by_ofnode() may fail, but
syscon_regmap_lookup_by_phandle() has logic in it to handle that case
correctly.
The previous implementation could read more than one syscon if the
"mediatek,pctl-regmap" property had more than one phandle, but the one
board with a devicetree that does that is not supported in U-Boot yet,
so we can save that for later (it may never be needed).
Fixes: 424ceba18b ("pinctrl: mediatek: support mediatek,pctl-regmap property")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Pass the unmapped parent ID when setting parent for mux clocks.
For technical reasons, some Mediatek clock driver have a mapping between
the clock IDs used in the devicetree and ID used in the generic clock
framework.
The mtk_clk_mux_set_parent() function is comparing the passed mapped
parent ID against the unmapped IDs in the chip-specific data structures.
Before this change, we were passing the mapped parent ID. When there is
a mapping, this resulted in buggy behavior (usually just incorrectly
failing to find a match and returning an error). We need to pass the
unmapped ID of the parent clock instead for the matching to work
correctly.
Since the reverse lookup is a bit verbose, a helper function is added to
keep the code clean.
Fixes: b135891572 ("clk: mediatek: add of_xlate ops")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Ignore the error return value from mtk_pinconf_bias_set_pupd_r1_r0().
The PUPD/R1/R0 registers only include a small subset of the pins, so
it is normal for this function to return an error for most pins.
Therefore, this error should not be propagated.
This fixes not all pins in a pinmux group being configured in some
cases because the propagated error caused the configuration loop to
exit early.
The rest of the function is refactored to return early on errors to
improve readability.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Set the size of the reg_cals arrays to PINCTRL_PIN_REG_MAX to in all
affected mediatek pinctrl drivers. This is needed to avoid potential
out-of-bounds accesses when they is used in mtk_hw_pin_field_get().
All array members need to be initialized since the code loops from 0
to PINCTRL_PIN_REG_MAX - 1. mt7622_reg_cals was already defined this
way, but the others were not.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Consistently use the device name in debug messages. The clk-uclass file
previously had a mix of printing the dev pointer and the device name.
Changing all to use the device name makes the debug messages more
useful.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Change the format specifier from %p to %s when printing the ofnode name
so that the actual name is printed instead of the pointer address.
Signed-off-by: David Lechner <dlechner@baylibre.com>
With commit 5663b137e6 ("arm: Remove edminiv2 board") the last
ARCH_ORION5X platform was removed. Remove the rest of the architecture
code which is now unused.
Reviewed-by: Tony Dinh <mibodhi@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/29031
- Fix interrupt storms in Linux on the imx93_frdm board.
- Defconfig update for tqma6 board.
- Miscellaneous cleanups/improvements for imx93_evk.
- Allow booting from both USB controlles on i.MX6 DHSOM.
- Handle third MAC address for SMARC i.MX95
