The font test makes assumptions about video devices and selected fonts that
may not hold true on other configurations like qemu-x86_64_defconfig.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
If CONFIG_CONSOLE_RECORD_INIT_F=y we need additional memory according to
CONFIG_CONSOLE_RECORD_OUT_SIZE_F.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
256 GiB is the default memory size of the sandbox. But in our CI other
boards like qemu-x86_64_defconfig run with a different memory size.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Skipping to the line starting with tsc reaches the tsc_base output not the
final tsc output.
Expect all the X86 specific lines in the bdinfo output.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
On ARM the bdinfo command prints architecture specific information.
The test needs to accept these output lines.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
We invoke the ut command in test_ut.py. Currently we only check for
failures. Instead we should also indicate if sub-tests were skipped.
With this change we will get output like the following for skipped tests:
test/py/tests/test_ut.py ..sssss......ss..............s.sssss.s.s...
================================ short test summary info ================================
SKIPPED [1] test/py/tests/test_ut.py:597: Test addrmap addrmap_test_basic has 1 skipped sub-test(s).
SKIPPED [1] test/py/tests/test_ut.py:597: Test bdinfo bdinfo_test_eth has 4 skipped sub-test(s).
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
CI: https://source.denx.de/u-boot/custodians/u-boot-stm/-/pipelines/28641
_ update LED management for STMicroelectronics boards
_ Add 1 GiB DRAM support for STM32MP13x DHCOR SoM
_ Fix 512 MiB DRAM support for STM32MP13x DHCOR SoM
_ Fix handling OPTEE in middle of the DRAM
_ Add missing debug UART build for STM32MP1 DHSOM
Remove get_led() and setup_led() which became obsolete since
led_boot_on() introduction. led_boot_on() is automatically called
from board_r.c
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Remove get_led() and setup_led() which became obsolete since
led_boot_on() introduction. led_boot_on() is automatically called
from board_r.c
Regarding "u-boot,error-led" property can't be used anymore since commit
Since commit 516a13e8db32 ("led: update LED boot/activity to new property implementation")
Instead get the LED labeled "red:status".
See kernel series: https://patchwork.kernel.org/project/linux-arm-kernel/list/?series=1022570
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Commit c37a668481 ("stm32mp: fix compilation issue with DEBUG_UART")
split the debug UART initialization code into two files, but failed to
update other non-ST boards. This did not lead to noticeable breakage
until debug UART is enabled, which is not the default. Update the
Makefile accordingly to allow debug UART to work.
Fixes: c37a668481 ("stm32mp: fix compilation issue with DEBUG_UART")
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add DRAM settings for 1 GiB variant of DH STM32MP13xx DHCOR SoM
and support for SoM DRAM coding HW straps decoding and automatic
DRAM configuration selection. Enable CONFIG_BOARD_EARLY_INIT_F on
all STM32MP1 DHSOM, as it is required for the HW straps decoding.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Update DRAM chip type and density comment for 512 MiB DRAM settings for
DH STM32MP13xx DHCOR DHSBC to match the chip on the SoM. No functional
change.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
STM32MP13xx may have OPTEE-OS at 0xdd000000 even on systems with 1 GiB
of DRAM at 0xc0000000, which is not the end of DRAM anymore. This puts
the OPTEE-OS in the middle of DRAM. Currently, the code sets RAM top to
0xdd000000 and prevents the DRAM range past OPTEE at 0xe0000000..0xffffffff
from being set as cacheable and from being usable. The code also sets the
area over OPTEE as invalid region in MMU tables, which is not correct.
Adjust the code such, that it only ever sets RAM top just before OPTEE
in case the OPTEE is really at the end of DRAM, mainly to be backward
compatible. Furthermore, adjust the MMU table configuration such, that
the regions over the OPTEE are simply skipped and not reconfigured, and
the regions between end of OPTEE and RAM top are set as cacheable, if
any actually exist.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Remove setting of fdt_high to ~0, which disables device tree relocation,
from the default environment. Doing so prevents U-Boot from correcting
problems such as having an unaligned device tree and leads to various
failure modes in the OS.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove setting of fdt_high to ~0, which disables device tree relocation,
from the default environment. Doing so prevents U-Boot from correcting
problems such as having an unaligned device tree and leads to various
failure modes in the OS.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove setting of fdt_high to ~0, which disables device tree relocation,
from the default environment. Doing so prevents U-Boot from correcting
problems such as having an unaligned device tree and leads to various
failure modes in the OS.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove setting of fdt_high to ~0, which disables device tree relocation,
from the default environment. Doing so prevents U-Boot from correcting
problems such as having an unaligned device tree and leads to various
failure modes in the OS.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove setting of fdt_high to ~0, which disables device tree relocation,
from the default environment. Doing so prevents U-Boot from correcting
problems such as having an unaligned device tree and leads to various
failure modes in the OS.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove setting of fdt_high to ~0, which disables device tree relocation,
from the default environment. Doing so prevents U-Boot from correcting
problems such as having an unaligned device tree and leads to various
failure modes in the OS. However, this platform also has a large comment
block that explains that given previous stage loaders and other parts of
the memory map (that may not be in the device tree we see?), adjust this
to use bootm_size to restrict relocation to be below the CMA area and
update the comment to match.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove setting of fdt_high to ~0, which disables device tree relocation,
from the default environment. Doing so prevents U-Boot from correcting
problems such as having an unaligned device tree and leads to various
failure modes in the OS.
Reviewed-by: Heiko Schocher <hs@nabladev.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove setting of fdt_high to ~0, which disables device tree relocation,
from the default environment. Doing so prevents U-Boot from correcting
problems such as having an unaligned device tree and leads to various
failure modes in the OS.
Signed-off-by: Tom Rini <trini@konsulko.com>
When this platform was removed the config header file was missed. Remove
that now.
Fixes: ddfc004009 ("arm: Remove xpress board")
Signed-off-by: Tom Rini <trini@konsulko.com>
When these platforms were removed the common config header file was
missed. Remove that now.
Fixes: a0cacddcaf ("arm: Remove zc5202 and zc5601 boards")
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove setting of fdt_high to ~0, which disables device tree relocation,
from the default environment. Doing so prevents U-Boot from correcting
problems such as having an unaligned device tree and leads to various
failure modes in the OS.
Tested-by: Greg Malysa <malysagreg@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
With the changes in commit 8fbcc0e0e8 ("boot: Assure FDT is always at
8-byte aligned address") to call memalign(...) we now always call
memalign(...) rather than malloc(...) when allocating a buffer that may
contain a device tree. However, memalign(...) is not portable among all
of the host OSes we support. The C11 standard does require that
aligned_alloc(...) exist and it takes the same parameters as
memalign(...) does. Change this file to call aligned_alloc rather than
memalign, and for the non-USE_HOSTCC case define that function back to
memalign.
Fixes: 8fbcc0e0e8 ("boot: Assure FDT is always at 8-byte aligned address")
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
