In case RX error occurs, and the RD_RFE bit is set, the descriptor
is never returned back to the queue. Make sh_eth_recv_start return
zero length in this case so that the descriptor can be released
and pushed back to the list. Also return the more appropriate
-EAGAIN instead of -EINVAL if the descriptor is not ready yet.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
U-Boot writes to RX packets when constructing replies.
This can cause stale cached data to be written to RX
buffer while we're receiving a packet. This causes RX
packet corruption because we invalidate the cache right
before processing the packet. Invalidate packet buffer
cache when preparing RX descriptor as well. This seems
to fix RX packet drops with high RX traffic.
While at it flush the descriptors right before enabling
RX/TX in sh_eth_tx_desc_init/sh_eth_rx_desc_init callbacks
when they are ready instead of flushing after allocation.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The common code is now capable of handling reset GPIO associated
with PHY. Drop the local ad-hoc code in favor of common code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The common code is now capable of handling reset GPIO associated
with PHY. Drop the local ad-hoc code in favor of common code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
These two properties are used by various DTs in place of
current reset-assert-us/reset-deassert-us , handle both .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
In case a new PHY is created and DM_ETH_PHY is enabled, bind a
generic PHY driver from ETH_PHY uclass to the PHY to have a
matching DM representation of that PHY.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The phy_connect_dev() is legacy API, now that there are no users,
make it internal to phy.c and unpublish it from headers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This patch adds 4-byte address mode support. Because traditional access
based on FIFO/shift register, it's complex to specify information like
opcode, address length, dummy bytes etc to flash. Replace the traditional
access by spi-mem layer which is essential to make 4-byte address mode
support possible.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Cong Dang <cong.dang.xn@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Move strobe delay setting code into extra function and reflect the latest
setting in datasheet (R-Car Gen3 v2.20, R-Car V3U v0.50).
i.e. STRTIM[2:0] should be set to 110 (RCar M3-W) or 111 (Other products)
This is also a preparation for new R-Car Gen4 SoC which has 4-bits STRTIM
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Fix for RZ/A1
In the FWU Multi Bank Update feature, the information about the
updatable images is stored as part of the metadata, on a separate
region. Add a driver for reading from and writing to the metadata
when the updatable images and the metadata are stored on a raw
MTD region.
The code is divided into core under drivers/fwu-mdata/ and some helper
functions clubbed together under lib/fwu_updates/
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The common code can now read, verify and fix meta-data copies
while exposing one consistent structure to users.
Only the .read_mdata() and .write_mdata() callbacks of fwu_mdata_ops
are needed. Get rid of .get_mdata() .update_mdata() .get_mdata_part_num()
.read_mdata_partition() and .write_mdata_partition() and also the
corresponding wrapper functions.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Reviewed-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Instead of each i/f having to implement their own meta-data verification
and storage, move the logic in common code. This simplifies the i/f code
much simpler and compact.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Sughosh Ganu <sughosh.ganu@linaro.org>
This is a remnant from when the USB controller driver managed
the reset signal itself. A patch from the very end of 2018 changed
this driver to delegate reset (and clock) management to the proper
control unit driver, but left this unused define behind.
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
arch/arm/dts/rk3399.dtsi has a node
usb_host0_ehci: usb@fe380000 {
compatible = "generic-ehci";
with clocks:
clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>,
<&u2phy0>;
The first 2 refer to nodes with class UCLASS_CLK, but &u2phy0
has class UCLASS_PHY.
u2phy0: usb2phy@e450 {
compatible = "rockchip,rk3399-usb2phy";
Since clk_get_bulk() only looks for devices with UCLASS_CLK,
it fails with -ENODEV and then ehci_usb_probe() aborts.
The consequence is peripherals connected to a USB 2 port (e.g. in a
Rock Pi 4 the white port, nearer the edge) not being detected.
They're detected if CONFIG_USB_OHCI_GENERIC is selected in Kconfig,
because ohci_usb_probe() does not abort when one clk_get_by_index()
fails, but then they work in USB 1 mode.
rk3399.dtsi comes from linux and the u2phy0 was added[1] to the clock
list in:
commit b5d1c57299734f5b54035ef2e61706b83041f20c
Author: William wu <wulf@rock-chips.com>
Date: Wed Dec 21 18:41:05 2016 +0800
arm64: dts: rockchip: add u2phy clock for ehci and ohci of rk3399
We found that the suspend process was blocked when it run into
ehci/ohci module due to clk-480m of usb2-phy was disabled.
[...]
Suspend concerns don't apply to U-Boot, and the problem with U-Boot
failing to probe EHCI doesn't apply to linux, because in linux
rockchip_usb2phy_clk480m_register makes u2phy0 a proper clock provider
when called by rockchip_usb2phy_probe().
So I can think of a few alternative solutions:
1- Change ehci_usb_probe() to make it more similar to
ohci_usb_probe(), and survive failure to get one clock. Looks a
little harder, and I don't know whether it could break something if
it ignored a clock that was important for something else than
suspend.
2- Change rk3399.dtsi effectively reverting the linux commit
b5d1c57299734f5b54035ef2e61706b83041f20c. This dealigns the .dtsi
from linux and seems fragile at the next synchronisation.
3- Change the clock list in rk3399-u-boot.dtsi or somewhere else.
This survives .dts* sync but may survive "too much" and miss some
change from linux that we might want.
4- Enable CONFIG_USB_OHCI_GENERIC and use the ports in USB 1 mode.
This would need to be made for all boards using rk3399. In a
simple test reading one file from USB storage it gave 769.5 KiB/s
instead of 20.5 MiB/s with solution 2.
5- Trying to replicate linux and have usb2phy somehow provide a clk,
or have a separate clock device for usb2phy in addition to the phy
device.
This patch tries to implement option 5 as Marek Vasut requested in
December 5th. Options 1 and 3 didn't get through [2][3].
It just registers usb2phy as a clock driver (device_bind_driver()
didn't work but device_bind_driver_to_node() did), without any
specific operations, so that ehci-generic.c finds it and is happy. It
worked in my tests on a Rock Pi 4 B+ (rk3399).
Link: [1] https://lkml.kernel.org/lkml/1731551.Q6cHK6n5ZM@phil/T/
[2] https://patchwork.ozlabs.org/project/uboot/patch/20220701185959.GC1700@begut/
[3] https://patchwork.ozlabs.org/project/uboot/patch/Y44+ayJfUlI08ptM@localhost/
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@vrull.eu>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Christoph Fritz <chf.fritz@googlemail.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # rk3399, rk3328, rv1126
The `musb_register` function returns some ERR_PTR(...) on failure,
not NULL, so update the check here appropriately.
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
According to the dm_serial_ops documentation, pending() should:
> @return number of waiting characters, 0 for none, -ve on error
And:
> It is acceptable to return 1 if an indeterminant number
> of characters is waiting.
With the current implementation, we have:
* FIFO is full -> pending() returns 0
* FIFO is partially used -> pending() returns 1
* FIFO is empty -> pending() returns 1
This is not the same as what the documentation requires.
Moreover, since [1], arm reset now flushes all console devices
(including serial) before the cpu gets reset.
Because of the flawed logic:
=> reset # user calls reset
flush() is called
_serial_flush() is called
ops->pending(dev, false) # never returns false
# board hangs indefinitely without resetting.
Fix it by using AML_UART_TX_EMPTY instead of AML_UART_TX_FULL.
[1] commit c5f4cdb8eb ("console: Use flush() before panic and reset"),
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230606-fix-meson-serial-pending-v1-1-6a54d4a01f76@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
In the current implementation, in case of I2C arbitration lost, a retry is
attempted; the message counter and pointer are reset to the original values
and the I2C xfer process is restart from the beginning.
However the message counter and message pointer are respectively
decremented and incremented by one before attempting any transfer, causing
the 1st transfer not to be actually retried (in case of a single transfer,
nothing is actually retried at all).
This patch fixes this: in case of retry, the 1st transfer is also retried.
Tested on a ZynqMP Kria board, with upstream older u-boot, but the involved
file and underlying logic seem basically the same.
Signed-off-by: Andrea Merello <andrea.merello@iit.it>
Failure can happen when i2c is used without initializing pinctrl properly,
which U-Boot happily allows in SPL. Without this fix, further I2C access would
fail, even after proper pinctrl initialization.
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add support for j721s2-wiz-10g device to use clock-names interface
instead of explicitly defining clock nodes within device tree node.
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Compiling with gcc 13 results in an error:
drivers/axi/axi-emul-uclass.c:16:5: warning: conflicting types for
‘axi_sandbox_get_emul’ due to enum/integer mismatch; have
‘int(struct udevice *, ulong, enum axi_size_t, struct udevice **)’
{aka ‘int(struct udevice *, long unsigned int, enum axi_size_t,
struct udevice **)’} [-Wenum-int-mismatch]
16 | int axi_sandbox_get_emul(struct udevice *bus, ulong address,
| ^~~~~~~~~~~~~~~~~~~~
In file included from drivers/axi/axi-emul-uclass.c:14:
./arch/sandbox/include/asm/axi.h:48:5: note: previous declaration of
‘axi_sandbox_get_emul’ with type ‘int(struct udevice *, ulong, uint,
struct udevice **)’ {aka ‘int(struct udevice *, long unsigned int,
unsigned int, struct udevice **)’}
48 | int axi_sandbox_get_emul(struct udevice *bus, ulong address, uint length,
| ^~~~~~~~~~~~~~~~~~~~
Adjust the header definition to match the implementation.
Define the size parameter as constant.
Fixes: 9a8bcabd8a ("axi: Add AXI sandbox driver and simple emulator")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The "Message not acknowledged" error message is missing a line feed,
leading to the console log getting garbled and joined together with
whatever the next output is in case this error happens:
"ti_sci system-controller@44043000: Message not acknowledgedAuthentication failed!"
Fix ths by adding the missing linefeed character.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Acked-by: Andrew Davis <afd@ti.com>
Buffers created through DEFINE_(CACHE_)ALIGN_BUFFER are actually
pointers to the real underlying buffer. Using sizeof(...) is
not appropriate in this case.
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
As per [1], dfu_alt_info is mentioned to be as semicolon separated
string of information on each alternate and the parsing logic in
the dfu.c is based on this.
Typically, the dfu_alt_info_* is defined in .h files as preprocessor
macros with 'alt' info separated by semicolon.
But when dfu_alt_info_* is added in the environment files(.env)
the script at "scripts/env2string.awk" converts a newline to space.
Thus adding a space character after semicolon. This results in
incorrect parsing in dfu.c which is based on the information that
'alt' info are only semicolon separated.
One option is to add dfu_alt_info_* variable in .env in single line.
But there is possiblity for it to exceed the line length limit.
So update the parsing logic to remove leading space characters
before adding to the dfu list.
[1]: https://u-boot.readthedocs.io/en/latest/usage/dfu.html
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
It seems like the header inclusion guard for the Exynos pinctrl header
was misspelled.
Make the preprocessor symbol for the #ifndef and #define lines the
same, so that the double inclusion protection works as expected.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This platform is currently unmaintained and untested, so remove it.
Further, as it is the only TI816X SoC example, remove related files as
well.
Signed-off-by: Tom Rini <trini@konsulko.com>
The PCIe controller on the M2 Pro/Max is different from the one
found on earlier Apple SoCs. Some registers moved and te meaning
of the bits in some other registers changed. But they are still
similar enough to handle both controllers in the same driver.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Add trivial driver for the MXS AUART IP. This is the other UART IP
present in i.MX23 and i.MX28, used to drive the non-DUART ports.
Signed-off-by: Marek Vasut <marex@denx.de>
The rank setting flow should be updated to support multi
fsp config.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update the DDR init flow for multi-setpoint support on i.MX93. A new
fsp_cfg struct need to be added in the timing file to store the diff
part of the DDRC and DRAM MR register for each setpoint.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add 625M bypass clock that may be used DRAM 625M
bypass mode support.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
