- Kautuk's semihosting patch:
move semihosting library from arm directory to common place and add
RISC-V support
- Zong's Kconfig patch:
use "imply" instead of "select" to allow user to decide if
SPL_SEPARATE_BSS should be selected
Second set of u-boot-at91 fixes for the 2023.01 cycle:
This is a single tiny fix that allows the correct name for one pin on
sama7g5 device. People with DT coming from Linux will have build errors
without this if they add NAND device.
Use imply instead of select, then it can still be disabled by
board-specific defconfig, or be set to n manually.
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
When we enable CONFIG_SPL and CONFIG_SPL_SEMIHOSTING then the code
in common/spl/spl_semihosting.c tries to use the
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME string which remains undeclared
unless SPL_FS_EXT4 || SPL_FS_FAT || SPL_FS_SQUASHFS are configured.
Add a dependency of SPL_SEMIHOSTING in the depends for
SPL_FS_LOAD_PAYLOAD_NAME so that the code compiles fine.
Signed-off-by: Kautuk Consul <kconsul@ventanamicro.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
We factor out the arch-independent parts of the ARM semihosting
implementation as a common library so that it can be shared
with RISC-V.
Signed-off-by: Kautuk Consul <kconsul@ventanamicro.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
As there are no more non-DM_ETH cases for networking, remove this legacy
file and update the Makefile to match current usage.
Signed-off-by: Tom Rini <trini@konsulko.com>
As DM_ETH is required for all network drivers, it's now safe to remove
the non-DM_ETH support code fro usb_ether itself.
Signed-off-by: Tom Rini <trini@konsulko.com>
As DM_ETH is required for all network drivers, it's now safe to remove
the non-DM_ETH support code. Doing this removes some board support code
which was also unused. Finally, this removes some CONFIG symbols that
otherwise needed to be migrated to Kconfig, but were unused in code now.
Signed-off-by: Tom Rini <trini@konsulko.com>
We only need to enable DM_ETH if we have a networking driver. All
networking drivers depend on DM_ETH being enabled, and their selection
ensures DM_ETH will be enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
This platform had largely disabled networking support before. More
completely disable it by turning off CONFIG_NET.
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Mike Looijmans <mike.looijmans@topic.nl>
This platform had largely disabled networking support before. More
completely disable it by turning off CONFIG_NET.
Cc: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Tom Rini <trini@konsulko.com>
This platform had largely disabled networking support before. More
completely disable it by turning off CONFIG_NET.
Cc: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable watchdog timer on the DHSOM by default, both in U-Boot proper and
in SPL. This can be used in combination with boot counter by either SPL
or U-Boot proper to boot either copy of system software, e.g. in case of
full A/B update strategy.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Increment the boot counter already in U-Boot SPL instead of incrementing
it only later in U-Boot proper. This can be used by SPL to boot either of
two U-Boot copies and improve redundancy of software on the platform, e.g.
in case of full A/B update strategy.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Enable the stm32prog, stm32key, stboard commands on DHSOM.
Those can be used e.g. to implement verified boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
