In Linux, the warning messages are printed out by pr_warn().
We can use Linux-like log functions in tree-wide.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[primary] Check MMC 0:1 for /extlinux/extlinux.conf and boot
[fallback 1] Check MMC 0:1 zImage and run mmcbootz
[fallback 2] Check MMC 0:1 uImage and run mmcboot
[fallback 3] Check NAND partitions and run nandboot
If 'extlinux.conf' is not found on MMC 0, the previous boot behavior is
followed.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
To page mapping the lowest 2 bits needs to be 0x3.
If not fix this, the final lowest 3 bits for page mapping is 0x1
which is marked as reserved.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
After relocation, when error happends, it is hard to track
ELR and LR with asm file objdumped from elf file.
So subtract the gd->reloc_off the reflect the compliation address.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As discussed at [1], the Amlogic Meson GX SoCs can embed a BL31 firmware
and a secondary BL32 firmware.
Since mid-2017, the reserved memory address of the BL31 firmware was moved
and grown for security reasons.
But mainline U-Boot and Linux has the old address and size fixed.
These SoCs have a register interface to get the two firmware reserved
memory start and sizes.
This patch adds a dynamic reservation of the memory zones in the device tree bootmem
reserved memory zone used by the kernel in early boot.
To be complete, the memory zones are also added to the EFI reserved zones.
Depends on patchset "Add support for Amlogic GXL Based SBCs" at [2].
[1] http://lists.infradead.org/pipermail/linux-amlogic/2017-October/004860.html
[2] http://lists.infradead.org/pipermail/linux-amlogic/2017-November/005410.html
Changes since v1:
- switched the #if to if(IS_ENABLED()) to compile all code paths
- renamed function to meson_board_add_reserved_memory()
- added a mem.h header with comment
- updated all boards ft_board_setup()
Changes since RFC v2:
- reduced preprocessor load
- kept Odroid-C2 static memory mapping as exception
Changes since RFC v1:
- switch to fdt rsv mem table and efi reserve memory
- replaced in_le32 by readl()
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[trini: Fix warning on khadas-vim over missing <asm/arch/mem.h>
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds platform code for the Khadas VIM board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.
This initial submission supports UART, MMC/SDCard and Ethernet with the
Internal RMII PHY.
The meson-gxl-s905x-khadas-vim.dts is synchronised from the linux 4.13
stable tree as of 4.13.8.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This adds platform code for the Libre Computer CC "Le Potato" board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.
This initial submission supports UART, MMC/SDCard and Ethernet with the
Internal RMII PHY.
The meson-gxl-s905x-libretech-cc.dts is synchronised from the linux 4.13
stable tree as of 4.13.8.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Switch P212 Ethernet init to the common Ethernet init function.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Switch Odroid-C2 Ethernet init to the common Ethernet init function.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Introduce a generic common Ethernet Hardware init function
common to all Amlogic GX SoCs with support for the
Internal PHY enable for GXL SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Now, lib/libfdt/fdt_wip.c is the same as scripts/dtc/libfdt/fdt_wip.c
Change the former to a wrapper of the latter.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
All the other fdt_*_region() functions are located in fdt_region.c,
while only fdt_find_regions() was added to fdt_wip.c, strangely.
Move it to the suitable place.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the moment our exception entry code needs 34 instructions, so we
can't use put it directly into the table entry, which offers "only"
32 instructions there. Right now we just put an unconditional branch
there, then use a macro to place the 34 instructions *per entry* after
that. That effectivly doubles the size of our exception table, which
is quite a waste, given that we use it mostly for debugging purposes.
Since the register saving part is actually identical, let's just convert
that macro into a function, and "bl" into it directly from the exception
slot, of course after having saved at least the original LR.
This saves us about 950 bytes of code, which is quite a relief for some
tight SPLs, in particular the 64-bit Allwinner ones.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Adjust this test to use the unit test framework. Drop the two existing
commands for running the tests and replace them with a single
'ut compression' command, with sub-commands.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Continue to have ret = run_test_internal(...) in run_test so ret
is always initialized]
Signed-off-by: Tom Rini <trini@konsulko.com>
Include necessary headers explicitly without relying on indirect
header inclusion.
<common.h>, <malloc.h> are unneeded.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Linux derived log functions can be used anywhere and easily
turned on/off by CONFIG_LOGLEVEL.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This header was renamed to rawnand.h in Linux.
The following is the corresponding commit in Linux.
commit d4092d76a4a4e57b65910899948a83cc8646c5a5
Author: Boris Brezillon <boris.brezillon@free-electrons.com>
Date: Fri Aug 4 17:29:10 2017 +0200
mtd: nand: Rename nand.h into rawnand.h
We are planning to share more code between different NAND based
devices (SPI NAND, OneNAND and raw NANDs), but before doing that
we need to move the existing include/linux/mtd/nand.h file into
include/linux/mtd/rawnand.h so we can later create a nand.h header
containing all common structure and function prototypes.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This driver is highly dependent on the configuration from denali_dt.c
Please enable CONFIG_NAND_DENALI_DT if you use this driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
denali_setup_data_interface() is always used.
I put __maybe_unused for a temporal use, then forgot to delete it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Remove unnecessary DECLARE_GLOBAL_DATA_PTR and header includes.
<common.h> has been replaced with <linux/errno.h> and <linux/printk.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 72443c7f7d ("mtd: cfi: Add support for status register
polling") added a feature check to determine if status register
is available for certain flash chips. The "lower software bits"
register used to determine this feature is not backward compati-
ble. Older flash chips without this feature has reserved value
0xff. Instead of checking "lower software bits" register, use
CFI primary vendor-specific extended query. Since CFI version
1.4, software features can be read from offset 0x53 according to
document AN201168 from Cypress.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The u-boot.sym file is scanned to find unit test suites for execution. At
present it only finds those whose names start with 'dm' or 'env'. This
code is buried in the bowels of the test code so when adding a new suite
it is not easy to discover why it is ignored by the test framework.
There seems to be no need to make this restriction. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
At present the test setup is somewhat mixed with the test itself. But if
the test setup fails (which it should not) then the test is actually
invalid. Put all the test buffers and sizes in a struct and separate out
the core code into a function.
This will make it easier to move the code to use the unit test framework.
Signed-off-by: Simon Glass <sjg@chromium.org>
The logic to either iterate through a list of tests or pick a named test
is common to at lest two test suits. Move this logic into a new function
and call it from the environment tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
The kernel gets the ethernet MAC from the ethaddr variable, the omap boards for
devices with USB based eth adapters just set the usbethaddr which doesn't appear
to get passed to the kernel. The same Raspberry Pi code sets both ethaddr and
usbethaddr so lets do that so linux (tested 4.13 and 4.14) get a static rather
than a random MAC address, while not regressing users of usbethaddr.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
The DCLK_VOP_DIV_CON_MASK should cover only bits 8 through 15.
Fix this to remove an "integer-overflow on shifted constant" warning.
Fixes: 9246d9e ("rockchip: rk3128: add clock driver")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The PLL selector field for NANDC is only 2 bits wide.
This fixes an 'int-overflow on shift' warning.
Fixes: 9246d9e ("rockchip: rk3128: add clock driver")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
On the RK3399-Q7, we want to trigger a full platform reset (so the
various software stacks supported don't have to deal with the same
complexities over and over again) in case that anything other than a
power-on reset occurred.
To do so, this defines the /config/sysreset-gpio property and has it
point to a GPIO that will perform a power-on reset of the entire
platform.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
The reset circuitry in the RK3399 only resets 'almost all logic' when
a software reset is performed. To make our software maintenance
easier in the future, we want to have the option (controlled by a DTS
property) to force all reset causes other than a power-on reset to
trigger a power-on reset via a GPIO trigger.
This adds the necessary support to the rk3399-puma (i.e. RK3399-Q7)
board-support and the documentation for the new property
(sysreset-gpio) within the /config-node.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
USB1 is connected to the on-module USB 3.0 hub and power to the hub
(actually it's a reset signal, modeled as a fixed regulator, that will
be released) should be enabled only during the first probing of the
device to avoid the hub from entering its low-power mode (where it
tries to attach on a fixed interval, but we always miss the timeslot
when U-Boot has the controller listening).
This adds a 'tsd,usb-port-power' stringlist to enable the
infrastructure in the board-specific usb_hub_reset_devices to find and
control the fixed regulator associated with control of the USB hub.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
For some versions of the RK3399-Q7 (at least revisions v1.1 and v1.2
are affected), we need to turn on the power for the port connected to
the on-module USB hub only when the device is probed for the first
time to ensure that the hub does not enter a low-power mode (that
U-Boot's USB stack can't deal with).
Note that this is needed for U-Boot only, as Linux eventually manages
to attach the hub even when it has entered into its low-power state
(when the hub wakes up the next time) after a few seconds.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Even if the board-specific directory Makefile doesn't have any
targets, it still needs to exist.
This adds a minimal Makefile for the board/rockchip/evb_rk3128
directory and a evk-rk3128.c (as built-in.o needs to be built
for every directory that a Makefile gets run for).
Fixes: c7a6866 ("rockchip: rk3128: add evb-rk3128 support")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add dts binding header for rk3128, files origin from kernel.
Series-Changes: 2
- fix i2c address
- add saradc and usb phy node
- emmc using fifo mode for there is no dma support in rk3128 emmc
- add some clock id in cru.h
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
With some of the recent cleanups (e.g. moving the DRAM controller
drivers for Rockchip devices to drivers/ram/rockchip), the files
and paths listed in MAINTAINERS no longer covered what really is
looked after as part of the Rockchip port.
This commit updates the files/paths listed in MAINTAINERS for the
Rockchip port. I am certain, though, that this will have missed some
additional paths that should have been included...
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Rework the ULCB CPLD driver and make it into a sysreset driver,
since that is what the ULCB CPLD driver is mostly for.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The order of members in struct hws_topology_map is cas_wl, cas_l. The
comments in the original db-88f6820-gp.c had this wrong and have been
copied to other Armada-385 based boards. Practically this hasn't made a
difference since all these boards set both cas_wl and cas_l to 0
(autodetect) but if there were ever a board that did need to set these
explicitly they would run into unexpected issued.
Update the comments to reflect the correct order of structure members.
Reported-by: Tobi Wulff <tobi.wulff@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
CONFIG_ENV_IS_IN_NAND has been removed in commit 2be296538e (Convert
CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig).
CONFIG_ENV_IS_IN_SPI_FLASH has been removed in commit 91c868fe7c
(Convert CONFIG_ENV_IS_IN_SPI_FLASH to Kconfig). The environment #ifdef
is now empty. Remove it.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Check if we are booting from NAND and let the bootrom
continue to load the rest of the bootloader
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Stefan Roese <sr@denx.de>
It's the first 8 bits of the bootrom error register that
contain the boot error/fallback error code. Let's check that
and continue to boot from UART.
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Stefan Roese <sr@denx.de>
bbt_mirror_descr and bbt_main_descr is defined but not used
when compiling without CONFIG_SYS_NAND_USE_FLASH_BBT set.
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes the inclusion of the libgcc math functions and
replaces them by functions coded in C, taken from the coreboot
project. This makes U-Boot building more independent from the toolchain
installed / available on the build system.
The code taken from coreboot is authored from Vadim Bendebury
<vbendeb@chromium.org> on 2014-11-28 and committed with commit
ID e63990ef [libpayload: provide basic 64bit division implementation]
(coreboot git repository located here [1]).
I modified the code so that its checkpatch clean without any
functional changes.
[1] git://github.com/coreboot/coreboot.git
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Currently X86 does not properly support distro defaults.
This patch is only a partial fix.
It provides the name of the bootloader EFI application
for the X86 architecture.
The architecture dependent file names are defined in the UEFI
specification.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This reverts commit 13c531e52a.
The error message with FIT style image mentioned in the above commit
only happens when booting using FIT image containing bzImage kernel
and without setup node (setup.bin). The current documentation for
x86 FIT support in doc/uImage.FIT/x86-fit-boot.txt mentions that
kernel's setup.bin file is required for building x86 FIT images.
The above commit breaks FIT images generated as described in the
documentation. Revert it to allow booting with images built in the
documented way.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
x86_vendor_name is defined as
static const char *const x86_vendor_name[]
So its elements should not be compared to 0.
Remove superfluous paranthesis.
Problem identified with Coccinelle.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Adjust VGA rom address to 0xfffb0000 so that u-boot.rom image
can be built again.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
ROM has been made read-only in qemu recently (namely commit 208fa0e4:
"pc: make 'pc.rom' readonly when machine has PCI enabled"). So this
patch restores compatibility between U-Boot and qemu.
Signed-off-by: Anton Gerasimov <anton@advancedtelematic.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: mention qemu commit title in the commit message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Before this patch one could receive following errors when executing "fatls"
command on machine with cache enabled (ex i.MX6Q) :
=> fatls mmc 0:1
CACHE: Misaligned operation at range [4f59dfc8, 4f59e7c8]
CACHE: Misaligned operation at range [4f59dfc8, 4f59e7c8]
ERROR: v7_outer_cache_inval_range - start address is not aligned - 0x4f59dfc8
ERROR: v7_outer_cache_inval_range - stop address is not aligned - 0x4f59e7c8
CACHE: Misaligned operation at range [4f59dfc8, 4f59e7c8]
CACHE: Misaligned operation at range [4f59dfc8, 4f59e7c8]
ERROR: v7_outer_cache_inval_range - start address is not aligned - 0x4f59dfc8
ERROR: v7_outer_cache_inval_range - stop address is not aligned - 0x4f59e7c8
To alleviate this problem - the calloc()s have been replaced with
malloc_cache_aligned() and memset().
After those changes the buffers are properly aligned (with both start
address and size) to SoC cache line.
Fixes: 09fa964bba ("fs/fat: Fix 'CACHE: Misaligned operation at range' warnings")
Suggested-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
This board is based on the Atmel sama5d3 eval boards.
Supporting the following features:
- Boot from NAND Flash
- Ethernet
- FIT
- SPL
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
This board is based on the Atmel 9x5 eval board.
Supporting the following features:
- Boot from NAND Flash
- Ethernet
- FIT
- SPL
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
GCC 7.1 seems to be smart enough to track val through the various
static inline functions, but not smart enough to see that val will
always be initialised when no error is returned. This triggers
the following warning:
env/mmc.c: In function 'mmc_get_env_addr':
env/mmc.c:121:12: warning: 'val' may be used uninitialized in this function [-Wmaybe-uninitialized]
To make it easier for compiler to understand what is going on, let's
initialise val.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Building spl with CONFIG_OF_EMBED enabled results in an error message
on my board: "SPL image too big". This is because the fdtgrep build
step is only executed for CONFIG_OF_SEPARATE.
Fix this by moving the fdtgrep build step ('cmd_fdtgreo') from
scripts/Makefile.spl to dts/Makefile so that the reduced dtb is
available for all kinds of spl builds.
The resulting variable name for the embedded device tree blob changes,
too, which is why common.h and fdtdec.c have tiny changes.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In U-Boot, this device tree is compatible with both the Torpedo and
SOM-LV kits. Let's rename it in the device tree since the U-Boot code and
show a more generic OMAP3 name. The code auto detects between the two and
loads the proper DTB file for Linux. This would eliminate the SOM-LV showing
the name Torpedo during boot and hopefully eliminate some confusion.
Signed-off-by: Adam Ford <aford173@gmail.com>
It is unwise to first dereference a variable
and then to check if it was NULL.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When copying the command line buffer the target array should
at least have the same size.
Cf. definition of console_buffer in common/cli_readline.c.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
use ALLOC_CACHE_ALIGN_BUFFER_PAD for mbr header allocation
in stack to fix alloc issue in is_gpt_valid()
this patch fix also issue for GPT partition handling
with blocksize != 512 in set_protective_mbr()
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add a header for SAMA5D2 SMC since it's not compatible with
SAMA5D3 one.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
[wenyou: fix the wrong base address of the SMC register]
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
The capabilities have default values which doesn't reflect the reality
when it concerns the base clock and the mul value. Use a fixe rate
for the gck. 240 MHz is an arbitrary choice, it is a multiple of the
maximum SD clock frequency handle by the controller and it allows to
get a 400 kHz clock for the card initialisation.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Differentiate the generic clock source selection value from the parent
clock index to fix the incorrect assignment of the generic clock
source selection.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
To get the same behavior as the Linux driver, instead of selecting
the closest inferior rate, select the closest inferior or superior
rate
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
What the AT91_UTMI depends on SPL_DM isn't right. AT91_UTMI is not
only used in SPL, also in other place, even if SPL_DM isn't enabled.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
MPU's region setup can be factorized between STM32F4/F7/H7 SoCs family
and used a common MPU's region config.
Only one exception for STM32H7 which doesn't have device area
located at 0xA000 0000.
For STM32F4, configure_clocks() need to be moved from arch_cpu_init()
to board_early_init_f().
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
In order to factorize code between STM32F4 and STM32F7
migrate all structs related to RCC clocks in include/stm32_rcc.h
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
MMC block needs 48Mhz source clock, for that we choose
to select the SAI PLL.
Update also stm32_clock_get_rate() to retrieve the MMC
clock source needed in MMC driver.
STM32F4 uses a different RCC variant than STM32F7. For STM32F4
sdmmc clocks bit are located into dckcfgr register whereas there
are located into dckcfgr2 registers on STM32F7.
In both registers, bits CK48MSEL and SDMMC1SEL are located at
the same position.
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Like STM32H7, now STM32F4/F7 clock drivers are binded by
MFD stm32_rcc driver.
This also allows to add reset support to STM32F4/F7 SoCs family.
As Reset driver is not part of SPL supported drivers, don't bind it
in case of SPL to avoid that stm32_rcc_bind() returns an error.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
This allows to add rcc MFD support to stm32f746-disco board
This rcc MFD driver manages clock and reset for STM32 SoCs family
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
STM32F4 doesn't get rcc.h file, to avoid compilation
issue, migrate RCC related defines from rcc.h to driver
file and remove rcc.h file.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Now that clk_stm32f7.c manages clocks for both STM32F4 and F7 SoCs
rename it to a more generic clk_stm32f.c
Fix also some checkpatch errors/warnings.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
STM32F4 and STM32F7 RCC clock IP are very similar.
Same driver can be used to managed RCC clock for
these 2 SoCs.
Differences between STM32F4 and F7 will be managed using
different compatible string :
_ overdrive clock is only supported by STM32F7
_ different sys_pll_psc parameters can be used between STM32F4
and STM32F7.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Align the RCC compatible string with the one used by kernel.
It will allow to use the same clock driver for STM32F4
and STM32F7 and to manage the differences between the 2 SoCs
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Add a dedicated stm32f7 compatible string to use clk_stm32f7
driver with both STM32F4 and STM32F7 SoCs.
It will be needed to manage differences between these 2 SoCs.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
PWR IP is used to enable over-drive feature in
order to reach a higher frequency.
Get its base address from DT instead of hard-coded value
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
This node is needed to enable performance mode
when system frequency is set up to 200Mhz.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Up to now we were able to read/write environment data from/to UBI
volumes only indirectly by gluebi driver. This driver creates NAND MTD
on top of UBI volumes, which is quite a workaroung for this use case.
Add support for direct read/write UBI volumes in order to not use
obsolete gluebi driver.
Forward-ported from this patch:
http://patchwork.ozlabs.org/patch/619305/
Original patch:
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Forward port:
Signed-off-by: S. Lockwood-Childs <sjl@vctlabs.com>
atcspi200 is Andestech spi ip which is embedded in
AE3XX and AE250 platforms. So rename as atcspi200
will be more reasonable to be used in different
platforms.
Signed-off-by: Rick Chen <rick@andestech.com>
ATCPIT100 is often used in AE3XX platform which is
based on NDS32 architecture recently. But in the future
Andestech will have AE250 platform which is embeded
ATCPIT100 timer based on RISCV architecture.
Signed-off-by: Rick Chen <rick@andestech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
ATCPIT100 is Andestech timer IP which is embeded
in AE3XX and AE250 boards. So rename AE3XX to
ATCPIT100 will be more make sence.
Signed-off-by: rick <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It will be work fine with unsigned long declaretion in timer
register struct when system is 32 bit. But it will not work
well when system is 64 bit. Replace it by u32 and verify both
ok in 32/64 bit.
Signed-off-by: Rick Chen <rick@andestech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When requesting a GPIO, set the PFC GPSR register to GPIO mode,
otherwise the GPIO cannot work.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add hook into the PFC driver to allow the GPIO driver to toggle
GPSR registers into GPIO mode when GPIO is requested.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add code to handle single pins nodes from DT in addition to already
support groups handling.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Stop using the old ad-hoc SH I2C driver and use the new RCar IIC
driver instead. The SH I2C driver should be deprecated and removed
eventually.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Mark the PRR as u-boot,dm-pre-reloc in all Gen3 board DTs as it is
needed very early and turn on the CONFIG_SYSCON to allow the PRR
driver to bind as a syscon uclass.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Implement DM driver for the Renesas PRR into RCar cpu info and convert
all users with DM and OF enabled to this new driver. This means all of
the boards with DM and OF enabled can fetch PRR address from DT, which
is useful on ie. V3M which has different PRR address than the rest of
Gen3 SoCs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
As we have a proper clock framework driver, these macros are not
needed, so drop them and clean up the whitelist.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
These macros are no longer needed since the DRAM configuration is parsed
from the DT. Drop them all.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Drop the ad-hoc DRAM configuration with macros and just decode
the DRAM configuration from device tree instead. This makes it
far cleaner and easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since checkboard() is gone, rmobile_sysinfo is also pointless on Gen3.
Furthermore, nuke ad-hoc CONFIG_RCAR_BOARD_STRING which is also dead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The checkboard() function showing hard-coded board model for which the
U-Boot was built is superseded on Gen3 by show_board_info() displaying
the Model from device tree. Add small ifdef to stop compiling the
function into U-Boot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
We can now use rmobile_get_cpu_type() to check the CPU ID rather
than using a macro, make it so.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since both R8A7795 and R8A7796 now use the same files, unify the
Makefile entry to CONFIG_RCAR_GEN3.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Unify the R7A7795 and R8A7796 memory maps in memmap-gen3 and, for now,
select which one is used based on which SoC is selected. Since this is
done in C code instead of statically assigned now, the decision can be
taken by PRR SoC match as well, which will be done in a subsequent patch.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Replace the ad-hoc values in the PRR CPU ID table with macros,
so that users can use rmobile_get_cpu_type() can compare the
returned value with these macros to figure out on which CPU they
are running.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since the Gen3 clock driver now has a .remove callback, it is no
longer necessary to shut the clock down before booting Linux in the
arch_preboot_os hook. Stop using it and while doing so, remove all
the ad-hoc config options which this hook used.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
These old PFC tables are no longer needed as there is now a proper
PFC pinmux driver in drivers/pinctrl/renesas . Remove them .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Pull out the GIC macros from the board configuration files
into the common Gen3 configuration file since these macros
are the same for all Gen3 systems.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This command is useless on Salvator-X as it is reading DRAM info from
SPD. We have no SPD on Salvator-X.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since the RCar Gen3 no longer uses the SH SDHI driver, but rather
uses the Matsushita SD driver, which loads all the properties from
device tree, these macros are no longer used, remove them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable the Micrel KSZ90x1 driver on ULCB, since the board is populated
with KSZ9031 and without this driver, the PHY cannot be operated.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The eMMC is 1V8 device only and the signaling is always 1V8,
fix the DT for ULCB to describe the hardware correctly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Fix handling of the reset GPIO. Drop the _nodev() suffix from the
gpio_request_by_name() call as there is now a proper DM capable
GPIO driver. Also check if the GPIO is valid before freeing it in
remove path, otherwise U-Boot will crash.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add driver for the RCar IIC or DVFS I2C controller. This driver is based
on the SH I2C driver, but supports DM and DT probing as well as modern
I2C framework API.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Unify the CONFIG_R8A7795 and CONFIG_R8A7796 as CONFIG_RCAR_GEN3
so that every time we add a new SoC, we won't have to add more
stuff to this list.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add xHCI entry into the clock tables, so that the xHCI USB driver
can enable the clock for the xHCI block via clock framework.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The MSTP registers were poked in boards/renesas/rcar-common/common.c
in arch_preboot_os hook thus far to shut down the clock before Linux
takes over. With DM, this is no longer needed and we can do the same
in the clock driver .remove callback. This patch adds such a .remove
callback for R8A7795 and R8A7796.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
It is legal to have multiple /memory nodes in a device tree . Currently,
fdtdec_setup_memory_size() only supports parsing the first node . This
patch extends the function such that if a particular /memory node does
no longer have further "reg" entries and CONFIG_NR_DRAM_BANKS still
allows for more DRAM banks, the code moves on to the next memory node
and checks it's "reg"s. This makes it possible to handle both systems
with single memory node with multiple entries and systems with multiple
memory nodes with single entry.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
To help out with the RCar/RMobile upstreaming, I'm adding myself
as the RCar/RMobile maintainer.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Xilinx changes for v2018.1
Zynq:
- Add support for Syzygy and cc108 boards
- Add support for mini u-boot configurations (cse)
- dts updates
- config/defconfig updates in connection to Kconfig changes
- Fix psu_init handling
ZynqMP:
- SPL fixes
- Remove slcr.c
- Fixing r5 startup sequence
- Add support for external pmufw
- Add support for new ZynqMP chips
- dts updates
- Add support for zcu102 rev1.0 board
Drivers:
- nand: Support external timing setting and board init
- ahci: Fix wording
- axi_emac: Wait for bit, non processor mode, readl/write conversion
- zynq_gem: Fix SGMII/PCS support
This patch uses readl and writel instead of in_be32 and
out_be32 for io ops as these internally uses readl,
writel for microblaze and for Zynq, ZynqMP there is
no need of endianness conversion and readl, writel
should work straightaway. This patch starts supporting
the driver for Zynq and ZynqMP platforms.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Dont enable SGMII and PCS selection if internal PCS/PMA
is not used, by getting the info about internal/external
PCS/PMA usage from dt property "is-internal-phy".
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use more accurate description for Xilinx Zynq and ZynqMP based platforms.
With using driver model there shouldn't be a need to create separate
Kconfig config options.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The chapter in which the table explaining the image format changed
chapter as the document evolved. This should help people track the
info down faster.
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Sparse is return warning about this:
arch/arm/mach-zynq/slcr.c: In function 'zynq_slcr_get_mio_pin_status':
arch/arm/mach-zynq/slcr.c:185:16: warning: comparison between signed and
unsigned integer expressions [-Wsign-compare]
for (i = 0; i < ARRAY_SIZE(mio_periphs); i++) {
^
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add proper support for EMIT_WRITE operation which is write only.
Do not use EMIT_MASKWRITE which is read-modify-write.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is based on work done in topic board where the first address
word also storing operation which should be done. This is reducing size
of configuration data.
This patch is not breaking an option to copy default ps7_init_gpl* files
from hdf file but it is doing preparation for ps7_init* consolidation.
The patch is also marking ps7_config as weak function.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add missing declaration to header.
Warning log:
arch/arm/mach-zynq/spl.c:94:12: warning: symbol 'ps7_post_config' was
not declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for non processor mode, this mode doesn't have
access to some of the registers and hence this patch
bypasses it and also length has to be calculated from
status instead of app4 in this mode.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
U-Boot is generally flashed to a MIPS Boston development board by means
of a .mcs file which Xilinx Vivado software can write to the flash
present on the board. As such we'd generally want to produce an mcs file
when building U-Boot to target the Boston board. Introduce a make target
for u-boot.mcs which generates it using the srec_cat tool available from
the SRecord project, and build it by default when srec_cat is present.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: u-boot@lists.denx.de
Generally we load Linux kernels on Boston boards in the form of FIT
images containing a compressed kernel binary. Linux is linked at
0x80100000 and so we need to decompress the kernel binary to that
address, however this is our default load address which means that
unless explicitly avoided we hit a decompression error as the
uncompressed kernel binary overwrites its compressed version from the
FIT image.
Avoid this by adjusting CONFIG_SYS_LOAD_ADDR to 0x88000000 (or
0xffffffff88000000 for MIPS64 builds) which avoids the address overlap
between compressed & uncompressed kernel binaries.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: u-boot@lists.denx.de
If we run on a CPU which doesn't implement a particular cache then we
would previously get stuck in an infinite loop, executing a cache op on
the first "line" of the missing cache & then incrementing the address by
0. This was being avoided for the L2 caches, but not for the L1s. Fix
this by generalising the check for a zero line size & avoiding the cache
op loop when this is the case.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: u-boot@lists.denx.de
When writing code, for example during relocation, we ensure that the
icache has a coherent view of the new instructions with a call to
flush_cache(). This handles the bulk of the work to ensure the new
instructions will execute as expected, however it does not ensure that
the CPU pipeline doesn't already contain instructions taken from a stale
view of the affected memory. This could theoretically be a problem for
relocation, but in practice typically isn't because we sync caches for
enough code after the entry point of the newly written code that by the
time the CPU pipeline might possibly fetch any of it we'll have long ago
written it back & invalidated any stale icache entries. This is however
a problem for shorter regions of code.
In preparation for later patches which write shorter segments of code,
ensure any instruction hazards are cleared by flush_cache() by
introducing & using a new instruction_hazard_barrier() function which
makes use of the jr.hb instruction to clear the hazard.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: u-boot@lists.denx.de
A typical use of cache maintenance functions is to force writeback of
data which a device is about to read using DMA - for example a
descriptor or command structure. Such users of cache maintenance
functions require that operations on the cache have completed before
they proceed to instruct a device to read memory. This requires that we
place a completion barrier (ie. sync instruction) between the cache ops
and whatever write informs the device to perform DMA.
Whilst strictly speaking this isn't all users of the cache maintenance
functions & we could instead place the barriers in the drivers that
require them, it would be much more invasive to do so than to just have
the barrier be the default by placing it in the cache functions
themselves. The cost is low enough that it shouldn't matter to us in any
rare cases that we use the cache functions when not performing DMA.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: u-boot@lists.denx.de
MIPS is no longer a part of Imagination Technologies, and as such my
@imgtec.com email address will soon cease to function. This patch
updates occurrances of it with my new @mips.com email address, and adds
an entry in .mailmap such that git (& tools such as get_maintainer.pl
when examining history) will use the new address.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: u-boot@lists.denx.de
The u-boot.lds linker script for MIPS defines a PTR_COUNT_SHIFT macro to
2 or 3 for 32 bit or 64 bit builds respectively. This macro is never
actually used though, so remove the dead code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The boston lowlevel_init() function zeroes the return register v0,
despite the function not being expected to return a value & that value
never being used.
Remove the redundant assignment to v0.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This work-around has been here in U-Boot because the AIDET and GPIO
drivers were missing in the upstream Linux. Both are now available
in Linus' tree:
- drivers/irqchip/irq-uniphier-aidet.c
- drivers/gpio/gpio-uniphier.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
I largely reworked the Denali NAND controller driver in Linux.
This commit imports the improvements from Linux. The code is
almost synced with Linux 4.15-rc1.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Several drivers check ->chipsize to see if the third row address cycle
is needed. Instead of embedding magic sizes such as 32MB, 128MB in
drivers, introduce a new flag NAND_ROW_ADDR_3 for clean-up. Since
nand_scan_ident() knows well about the device, it can handle this
properly. The flag is set if the row address bit width is greater
than 16.
Delete comments such as "One more address cycle for ..." because
intention is now clear enough from the code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 14157f861437ebe2d624b0a845b91bbdf8ca9a2d]
struct nand_ecc_caps was designed as flexible as possible to support
multiple stepsizes (like sunxi_nand.c).
So, we need to write multiple arrays even for the simplest case.
I guess many controllers support a single stepsize, so here is a
shorthand macro for the case.
It allows to describe like ...
NAND_ECC_CAPS_SINGLE(denali_pci_ecc_caps, denali_calc_ecc_bytes, 512, 8, 15);
... instead of
static const int denali_pci_ecc_strengths[] = {8, 15};
static const struct nand_ecc_step_info denali_pci_ecc_stepinfo = {
.stepsize = 512,
.strengths = denali_pci_ecc_strengths,
.nstrengths = ARRAY_SIZE(denali_pci_ecc_strengths),
};
static const struct nand_ecc_caps denali_pci_ecc_caps = {
.stepinfos = &denali_pci_ecc_stepinfo,
.nstepinfos = 1,
.calc_ecc_bytes = denali_calc_ecc_bytes,
};
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: a03c60178c181767ecfb26fb311a88742d228118]
Driver are responsible for setting up ECC parameters correctly.
Those include:
- Check if ECC parameters specified (usually by DT) are valid
- Meet the chip's ECC requirement
- Maximize ECC strength if NAND_ECC_MAXIMIZE flag is set
The logic can be generalized by factoring out common code.
This commit adds 3 helpers to the NAND framework:
nand_check_ecc_caps - Check if preset step_size and strength are valid
nand_match_ecc_req - Match the chip's requirement
nand_maximize_ecc - Maximize the ECC strength
To use the helpers above, a driver needs to provide:
- Data array of supported ECC step size and strength
- A hook that calculates ECC bytes from the combination of
step_size and strength.
By using those helpers, code duplication among drivers will be
reduced.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 2c8f8afa7f92acb07641bf95b940d384ed1d0294]
Some NAND controllers can assign different NAND timings to different
CS lines. Pass the CS line information to ->setup_data_interface() so
that the NAND controller driver knows which CS line is concerned by
the setup_data_interface() request.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 104e442a67cfba4d0cc982384761befb917fb6a1]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In some cases, nand_do_{read,write}_ops is passed with unaligned
ops->datbuf. Drivers using DMA will be unhappy about unaligned
buffer.
The new struct member, buf_align, represents the minimum alignment
the driver require for the buffer. If the buffer passed from the
upper MTD layer does not have enough alignment, nand_do_*_ops will
use bufpoi.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 477544c62a84d3bacd9f90ba75ffc16c04d78071]
Drivers setting NAND_ECC_CUSTOM_PAGE_ACCESS are supposed to handle the
full read/write page sequence, and waiting for a page to actually be
programmed is part of this write-page sequence.
This is also what is done in ->write_oob_xxx() hooks, so let's do that in
->write_page_xxx() as well to make it consistent.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 41145649f4acb30249b636b945053db50c9331c5]
[masahiro:
There is no driver setting NAND_ECC_CUSTOM_PAGE_ACCESS in U-Boot.
No driver is affected by this change.]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The ->errstat() hook is no longer implemented NAND controller drivers.
Get rid of it before someone starts abusing it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 7d135bcced20be2b50128432c5426a7278ec4f6d]
[masahiro: modify davinci_nand.c for U-Boot]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cached programming is always skipped, so drop the associated code until
we decide to really support it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 0b4773fd1649e0d418275557723a7ef54f769dc9]
[masahiro: modify davinci_nand.c for U-Boot]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In order to make the ecclayout definition completely dynamic we need to
rework the way the OOB layout are defined and iterated.
Create a few mtd_ooblayout_xxx() helpers to ease OOB bytes manipulation
and hide ecclayout internals to their users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 75eb2cec251fda33c9bb716ecc372819abb9278a]
[masahiro:
cherry-pick more code from adbbc3bc827eb1f43a932d783f09ba55c8ec8379]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If your controller already sends the required NAND commands when
reading or writing a page, then the framework is not supposed to
send READ0 and SEQIN/PAGEPROG respectively.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 3371d663bb4579f1b2003a92162edd6d90edd089]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add the tR_max, tBERS_max, tPROG_max and tCCS_min timings to the
nand_sdr_timings struct.
Assign default/safe values for the statically defined timings, and
extract them from the ONFI parameter table if the NAND is ONFI
compliant.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
[Linux commit: 204e7ecd47e26cc12d9e8e8a7e7a2eeb9573f0ba
Fixup commit: 6d29231000bbe0fb9e4893a9c68151ffdd3b5469]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When changing from one data interface setting to another, one has to
ensure a specific sequence which is described in the ONFI spec.
One of these constraints is that the CE line has go high after a reset
before a command can be sent with the new data interface setting, which
is not guaranteed by the current implementation.
Rework the nand_reset() function and all the call sites to make sure the
CE line is asserted and released when required.
Also make sure to actually apply the new data interface setting on the
first die.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: d8e725dd8311 ("mtd: nand: automate NAND timings selection")
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
[Linux commit: 73f907fd5fa56b0066d199bdd7126bbd04f6cd7b]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The NAND framework provides several helpers to query timing modes supported
by a NAND chip, but this implies that all NAND controller drivers have
to implement the same timings selection dance. Also currently NAND
devices can be resetted at arbitrary places which also resets the timing
for ONFI chips to timing mode 0.
Provide a common logic to select the best timings based on ONFI or
->onfi_timing_mode_default information. Hook this into nand_reset()
to make sure the new timing is applied each time during a reset.
NAND controller willing to support timings adjustment should just
implement the ->setup_data_interface() method.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[Linux commit: d8e725dd831186a3595036b2b1df9f68cbc6efa3]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
struct nand_data_interface is the designated type to pass to
the NAND drivers to configure the timing. To simplify further
patches convert the onfi_sdr_timings array from type struct
nand_sdr_timings nand_data_interface.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: b1dd3ca203fccd111926c3f6ac59bf903ec62b05]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently we have no data structure to fully describe a NAND timing.
We only have struct nand_sdr_timings for NAND timings in SDR mode,
but nothing for DDR mode and also no container to store both types
of timing.
This patch adds struct nand_data_interface which stores the timing
type and a union of different timings. This can be used to pass to
drivers in order to configure the timing.
Add kerneldoc for struct nand_sdr_timings while touching it anyway.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: eee64b700e26b9bcc6fce024681c31f5e12271fc]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When NAND devices are resetted some initialization may have to be done,
like for example they have to be configured for the timing mode that
shall be used. To get a common place where this initialization can be
implemented create a nand_reset() function. This currently only issues
a NAND_CMD_RESET to the NAND device. The places issuing this command
manually are replaced with a call to nand_reset().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 2f94abfe35b210e7711af9202a3dcfc9e779219a]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
'extern' is not necessary for function declarations. To prevent
people from adding the keyword to new declarations remove the
existing ones.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 79022591839f110f465cac0223e117b91d47d5db]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The generic NAND DT bindings allows one to tweak the ECC strength and
step size to their need. It can be used to lower the ECC strength to
match a bootloader/firmware config, but might also be used to get a better
reliability.
In the latter case, the user might want to use the maximum ECC strength
without having to explicitly calculate the exact value (this value not
only depends on the OOB size, but also on the NAND controller, and can
be tricky to extract).
Add a generic 'nand-ecc-maximize' DT property and the associated
NAND_ECC_MAXIMIZE flag, to let ECC controller drivers select the best
ECC strength and step-size on their own.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
[Linux commit: ba78ee00e1ff84de9b3ad33edbd3ec599099ee82]
[masahiro: of_property_read_bool -> fdt_getprop for U-Boot]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add stubs to the header in case CONFIG_SYS_NAND_ONFI_DETECTION is
disabled. This is much easier than adding around #ifdef to the
caller side.
Also, I removed the #ifdef around onfi_params. In Linux, onfi_params
and jedec_params are unified as union. It will be the right thing
to do.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Same macros are defined in various places. Collect them into
include/linux/bitops.h like Linux.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
These boards are on the boundary of "u-boot-nodtb.bin exceeds file
size limit" error.
Reduce the log-level to save memory footprint.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Read dma address using fdtdec_get_addr as it checks for
address cells and size cells and reads the address
properly. fdtdec_get_int always assume address is of int
size which goes wrong if using it on 64-bit architecture.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch makes SMMU work by moving the iommus node under the dwc3 child
entry from parent node.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch uncomments snps,quirk-frame-length-adjustment which has
the value to adjust the SOF/ITP generated from the controller.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds OTG interrupt support in device tree. It will add
an extra interrupt line number dedicated to OTG events. This will
enable OTG interrupts to serve in DWC3 OTG driver.
Signed-off-by: Manish Narani <mnarani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds CCI support for USB when CCI is enabled in design.
This patch also adds 'reg' property for Xilinx USB 3.0 IP. The 'reg'
property is added in order to modify a register in that to enable
coherency in Hardware.
Also add address to unit name to avoid dtc warning
Signed-off-by: Manish Narani <mnarani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for reading silicon revision using zynqmp nvmem
driver.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The AMS includes an ADC as well as on-chip sensors that can be used to
sample external voltages and monitor on-die operating conditions, such as
temperature and supply voltage levels.
Signed-off-by: Rajnikant Bhojani <rajnikant.bhojani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch sets host quirk2 bit field for No 1.8V supported in case of
1.0 silicon. The 1.0 silicon doesn't have support for UHS-I modes. This
property will ensure the SD runs on High Speed mode.
Signed-off-by: Manish Narani <mnarani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch modifies the phy_zynqmp.c driver to use reset-controller
framework for asserting/de-asserting reset for High Speed modules.
Also fix documentation and dtsi.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch add the reset nodes in zynqmp.dtsi which are used by
reset-controller framework
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Only silicon v1 requires this termination fix. With new nvmem soc
revision nvmem detection driver this can be autodetected at run time and
this flag is not needed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Generic dtsi file can't use the same mac address for all.
U-Boot read mac from eeprom in zcu102 case and for others random mac
address is generated.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
dtc reports issues with it.
arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dtb: Warning
(unit_address_format): Node
/amba/spi@ff040000/spi0_flash0@0/spi0_flash0@00000000 unit name should
not have leading 0s
arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dtb: Warning
(unit_address_format): Node
/amba/spi@ff050000/spi1_flash0@0/spi1_flash0@00000000 unit name should
not have leading 0s
arch/arm64/boot/dts/xilinx/zynqmp-ep108.dtb: Warning
(unit_address_format): Node
/amba/spi@ff040000/spi0_flash0@0/spi0_flash0@00000000 unit name should
not have leading 0s
arch/arm64/boot/dts/xilinx/zynqmp-ep108.dtb: Warning
(unit_address_format): Node
/amba/spi@ff050000/spi1_flash0@0/spi1_flash0@00000000 unit name should
not have leading 0s
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Some user space libraries reading platform compatible string and based
on that changing behavior. Mark revB board with revB string.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Currently DP power domain (pd_dp) is not attached to any of the DP nodes which is
causing genpd to trigger a power down request for DP domain, making all DP related
peripherals unusable. So assign power domains for all DP related nodes to enable
proper accounting of DP power domain usage.
Signed-off-by: Jyotheeswar Reddy <jyothee@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch disables the smmu and also removes the mmu-masters
Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds the calibration property with required value,
calculated based on rtc input crystal oscillator frequency (32.768Khz).
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
AXI master interface in CEVA AHCI controller requires two unique
Write/Read ID tags per port. This is because, ahci controller uses
different AXI ID[3:0] bits for identifying non-data transfers(like
reading descriptors, updating PRD tables, etc) and data transfers
(like sending/receiving FIS).To make SMMU work with SATA we need to
add correct SMMU stream id for SATA. SMMU stream id for SATA is
determined based on the AXI ID[1:0] as shown below
SATA SMMU ID = <TBU number>, 0011, 00, 00, AXI ID[1:0]
Note: SATA in ZynqMp uses TBU1 so TBU number = 0x1, so
SMMU ID = 001, 0011, 00, 00, AXI ID[1:0]
Since we have four different AXI ID[3:0] (2 for port0 & 2 for port1
as said above) we get four different SMMU stream id's combinations
for SATA. These AXI ID can be configured using PAXIC register.
In this patch we assumed the below AXI ID values
Read ID/ Write ID for Non-Data Port0 transfers = 0
Read ID/ Write ID for Data Port0 transfers = 1
Read ID/ Write ID for Non-Data Port1 transfers = 2
Read ID/ Write ID for Data Port1 transfers = 3
Based on the above values,SMMU stream ID's for SATA will be 0x4c0 &
0x4c1 for PORT0, 0x4c2 & 0x4c3 for PORT1. These values needed to be
added to iommus dts property. This patch does the same.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
All gpio controllers should contain this property.
This property is not checked by the code that's why this issue wasn't
found earlier.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The correct register size is 0x10000, otherwise
it overlaps with other register space.
Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This will simplify dt overlay structure for the whole PL.
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Extract from Linux mainline patch:
The ARM architected timer specification mandates that the interrupt
associated with each timer is level triggered (which corresponds to
the "counter >= comparator" condition).
A number of DTs are being remarkably creative, declaring the interrupt
to be edge triggered. A quick look at the TRM for the corresponding ARM
CPUs clearly shows that this is wrong, and I've corrected those.
For non-ARM designs (and in the absence of a publicly available TRM),
I've made them active low as well, which can't be completely wrong
as the GIC cannot disinguish between level low and level high.
The respective maintainers are of course welcome to prove me wrong.
While I was at it, I took the liberty to fix a couple of related issue,
such as some spurious affinity bits on ThunderX, and their complete
absence on ls1043a (both of which seem to be related to copy-pasting
from other DTs).
Acked-by: Duc Dang <dhdang@apm.com>
Acked-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
PM callbacks are delivered to the NS OS. Let the PM driver handle the
IRQ and retrieve callback data from the secure HW.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Changed min-residence to 10ms(was 100 ms) for cpu-sleep-0.
Tried lower values 5ms and 8ms and it worked fine with Debug Off.
But to accommodate PM Debug On case, 10 ms is required. With this
change, low power idle state is into effect more frequently.
Measured boot time with PM debugs On and Off. No change observed
compared to 100ms value.
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Acked-by: Will Wong <willw@xilinx.com>
Tested-by: Koteswararao Nayudu <kotin@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Version string has unused fields 31:20 which can be used for exporting 9
bits from efuse IPDISABLE regs to recognize eg/cg/ev devices.
These efuse bits are setup for certain devices.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This modifies default value of config DEFINE_TCM_OCM_MMAP
to yes if CONFIG_MP is defined MP supports needs OCM and TCM
part of memory map.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch is adding external pmufw "Platform Management Unit firmware"
to boot.bin image. Boot.bin is a Xilinx format which bootrom is capable
to read and boot the system. pmufw is copied to the header data section
follows by u-boot-spl.bin. pmufw is consumed by PMU unit (Microblaze)
and SPL runs on a53-0.
This is generated command line when PMUFW_INIT_FILE is setup.
./tools/mkimage -T zynqmpimage -R ./"" -n
./"board/xilinx/zynqmp/pmufw.bin" -d spl/u-boot-spl.bin spl/boot.bin
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch provides a Kconfig option to use specified
memory for MMU table using reserve_mmu platform specific
routine. Here we used TCM space for MMU table.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch corrects the R5 release sequence by adding the
below steps.
1. Flush dcache to ensure that image loaded into memory.
2. Keep R5 reset just to ensure R5 in reset.
3. Disable caches before accessing TCM as with out this
A53 can do speculative and may result in ECC failures
if TCM's are not initialized. So, it is always better
to disable dcaches before accessing TCM and enable back.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reported-by: John Linn <linnj@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add configuration files/dtses for mini u-boot configurations which runs
out of OCM.
ram top is calculated from 0 that's why +#define CONFIG_SYS_SDRAM_BASE
0xfffc0000
+#define CONFIG_SYS_SDRAM_SIZE 0x40000
was hardcoded.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
cc108 board is wiring uart via PL which is good platform for SPL fpga
support.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
All these configs were moved to Kconfig that's why this empty ifdef
structure is not needed anymore.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mention device-type = "ethernet-phy", as qemu will need this in absence
of compatible.
Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In legacy method, 1st stage bootloader was used to configure the HW
setting such as NAND timing. Hence, adding a config option in Zynq
NAND driver for the compatibility of device that using 1st stage
bootloder instead of U-boot SPL.
This commit is to add config option
CONFIG_NAND_ZYNQ_USE_BOOTLOADER1_TIMINGS that allow NAND driver use
timing values set by the 1st stage bootloader, instead of the hard-coded
values in the Zynq NAND driver.
Signed-off-by: Jeff Westfahl <jeff.westfahl@ni.com>
Signed-off-by: Wilson Lee <wilson.lee@ni.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Keng Soon Cheah <keng.soon.cheah@ni.com>
Cc: Chen Yee Chew <chen.yee.chew@ni.com>
Cc: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Scott Wood <oss@buserror.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In
if (a || b)
else if (!a)
the constraint (!a) is always true if else is reached and
can be removed.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This option prevents booting on am335x_evm at least along with most
likely other platforms.
Fixes: 337bbb6297 ("spl: fit: add SPL_FIT_IMAGE_TINY config to reduce code-size")
Signed-off-by: Tom Rini <trini@konsulko.com>
While the USB HW in the RZ/A is basically the same, there are some
differences from the original versions that were in the SH SoCs.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
icorem6 has sd on usdhci1 which is devno 0 so return proper
devno from board_mmc_get_env_dev for icorem6 and icorem_6rqs
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add new board names for existing board support
imx6q - icore and icore_rqs boards
imx6ul - geam6ul and isiot boards
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
As per USDHC boot eFUSE descriptions:
USDHC3 => devno 2
USDHC4 => devno 3
Linux will detect mmc0, mmc1, mmc2 based on the status
"okay" on usdhc so imx6qdl-icore-rqs.dtsi has enabled
usdhc1, usdhc3 and usdhc4.But U-Boot can detect based
on the aliases so add mmc1, mmc2 for usdhc3 and usdhc4
respectively and return the board_mmc_get_env_dev
by subtracting -1
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
before relocation pinctrl data BSS is overlapping DT area,
when .data is using uninitialized global variable,
imx6_pinctrl_soc_info. So assign them flags ZERO_OFFSET_VALID
to prevent BSS overlap
Suggested-by: Lokesh Vutla <lokeshvutla@ti.com>
Reported-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
mx6sxsabresd can run different kernel versions, such as NXP 4.1 or mainline.
Currently the rootfs location is passed via mmcblk number and the
problem with this approach is that the mmcblk number for the SD
card changes depending on the kernel version.
In order to avoid such issue, use the UUID method to specify the
rootfs location.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
imx_set_wdog_powerdown() is always used to disable the power down
enable bit, so remove the boolean parameter of the function.
It is also a bit strange to write a boolean value into registers,
so this new version makes explicit that we are writing 0.
While at it, rename it to imx_wdog_disable_powerdown().
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Clear powerdown enable bit for WDOG3 on i.MX6ULL to avoid unwanted
kernel reboots.
Suggested-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
i.MX6ULL has the same WDOG3 base address as i.MX6UL, so take this
into account in the base address definition.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The boot (and fallback/emergency boot) concept for the RK3399-Q7
differs from Rockchip's reference platforms.
On the RK3399-Q7, some of this functionality is present in the
bootloader itself (and configurable); some is backed in hardware by
the Qseven BIOS_DISABLE signal to invoke the final stages of fallbacks
(i.e. either an external boot bypassing on-module memories or falling
back to the BROM for USB recovery).
In summary: the ADC-based boot_mode check does not apply for the
RK3399-Q7 and we therefore disable it (in this commit) by setting
CONFIG_BOOT_MODE_REG to 0.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The ROCKCHIP_BOOT_MODE_REG option defaults to a hex value, so 0 will
show as 0x0 if a default is provided and changed via Kconfig.
However, it still will show as 0, if no default is given.
Consequently, the "is set to something other than 0" test in a
Makefile is cumbersome. Instead this check can easily be performed in
the C-code.
This removes the ifeq-check from mach-rockchip/Makefile, adds a
matching #if-check to boot_mode.c and fixes resulting link issues (if
boot_mode.o was not included due to the Makefile check) by defining a
stub function (in case the functionality is not built in) for
setup_boot_mode in boot_mode.c.
Fixes: e306779 (rockchip: make boot_mode related codes reused across all platforms)
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Existing FPGA program write is always assume RBF data >= 32 bytes, so
any rbf data less than 32 bytes writing to FPGA would be failed.
This patch enhances the FPGA program write to support rbf data with
size >= 4 bytes.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
This DT binding doc is porting from Linux DT binding doc.
commit 1adcbea4201a6852362aa5ece573f1f169b28113
Add a device tree bindings document for the SoCFPGA Arria10
FPGA Manager driver.
Signed-off-by: Alan Tull <atull@opensource.altera.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-By: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Increase the buffer length to be just above maximum permissible value
of 128 kiB . This increases the performance of the UMS and alike by a
factor of 2 - 2.5 as the buffers are less fragmented.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Lukasz Majewski <lukma@denx.de>
When usb_hub_reset_devices is called, it should be passed both an
indicator which hub it should operate on and what port number (local
to that hub) should be reset.
Previously, the usb_hub.c code did not include such context and
always started resets from port number 1, performing multiple
reset-requests for the same devices:
/*
* Reset any devices that may be in a bad state when applying
* the power. This is a __weak function. Resetting of the devices
* should occur in the board file of the device.
*/
for (i = 0; i < dev->maxchild; i++)
usb_hub_reset_devices(i + 1);
This adds an additional 'hub' parameter to usb_hub_reset_devices
that provides the context to fully qualify the port-number in.
Existing implementations are changed to accept and ignore the new
parameter.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Its a valid use case to call ehci_submit_async() with a NULL buffer
with length 0. E.g. from usb_set_configuration().
As invalidate_dcache_range() isn't able to judge if the address
NULL is valid or not (depending on the SoC hardware configuration it
might be valid) do the check in ehci_submit_async() as here we know
that we don't have to invalidate such a buffer.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Currently we check in ehci_shutdown() if ctrl is NULL after
dereferencing it.
Before this we have already dereferenced ctrl, ctrl->hccr,
and ctrl->hcor in ehci_get_portsc_register(), ehci_submit_root(),
and hci_common_init().
A better approach is to already check ctrl, ctrl->hccr, and ctrl->hcor
during the initialization in ehci_register() and usb_lowlevel_init()
and signal an error here via the return code.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add firmware V3, firmware loader and XHCI glue for the Renesas R-Car
Gen3 SoCs XHCI controller. Thus far only the R-Car Gen3 R8A7795 ES2.0+
and R8A7796 are supported.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Commit 9000eddbae ("drivers/usb/ehci: Use platform-specific accessors")
broke USB 2.0 on big-endian platforms because for them writel/readl()
does automatic conversion of BE data to LE.
Proper implementation requires to use "raw" variant of these accessors
which read/write data without messing with endianess.
While at it replace cpu_to_be32() to be32_to_cpu() in readl() to
keep sane semantics.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Marek Vasut <marex@denx.de>
Reported-by: Vladimir Boroda <boroda@yahoo.com>
Usb tree/info commands iterate over all usb uclass devices recursively.
Blk uclass devices based on struct blk_desc are created for mass storage
device, treating them as usb uclass devices based on struct usb_device
and referencing usb config interface descriptors cause crash.
To fix, ignore blk and usb_emul uclass devices in usb_show_info
and usb_tree_graph. Also avoid addition of preamble for blk uclass
child devices, otherwise tree dump gets messed up.
Signed-off-by: Suneel Garapati <suneelglinux@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The RK3399 has a total of 9 I2C controllers. To support these, the
enum in periph.h is extended and the mapping from the IRQ numbers to
the peripheral-ids is extended to ensure that pinctrl requests are
passed through to the function configuring the I2C pins.
For I2C8, the pinctrl is implemented and tested (on a RK3399-Q7) using
communication with the FAN53555 connected on I2C8.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
The RK3399 clk driver still has a left-over use of extract_bits, which
can be replaced by using bitfield_extract from include/bitfield.h.
This rewrites the invocation to use the shared function.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
A minor code-size increase from the changes for tracking the os-type
of FIT images and from infrastructure for recording the loadables into
the the loaded FDT, broke the builds for sun50i and some OMAP2+ devices.
This change adds a new config option (enabled by default for
MACH_SUN50I, MACH_SUN50I_H5 and ARCH_OMAP2PLUS) that does skips these
processing steps (bringing code size down to below the limit
again). The os-type is not evaluated, but assumed to be IH_OS_UBOOT
(i.e. taking the code-paths intended for backward-compatibility).
Note that enabling this config option precludes any useful downstream
processing, such as utilising a special calling convention for ATF or
OPTEE, based on the os-type of the loadables.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This tracks the SPL changes for ATF for the RK3368-uQ7:
* renames ATF_SUPPORT to ATF
* drops CONFIG_SPL_ATF_TEXT_BASE (now dynamically retrieved from
the .itb file)
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This defconfig update makes use of the new features:
* CONFIG_ROCKCHIP_SPL_RESERVE_IRAM is now set to 0, as there is no
overlap between the M0 firmware and the ATF (we load this to DRAM
and relocate it to its final location within the ATF)
* tracks the ATF_SUPPORT -> ATF renaming
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For the RK3368-uQ7, we can now update the .its file to mark the
Trusted Firmware as out 'firmware' bootable and annotate both ATF and
U-Boot with an OS-type.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit updates the .its file for the RK3399-Q7 to use the new
features and demonstrates how to use those:
* it marks the ATF as the 'firmware'
* it tracks the OS-type for U-Boot and ATF
* it loads the PMU (M0) firmware to DRAM and records the location
to /fit-images (where our ATF reads it from)
With the handoff of the next-stage FDT to ATF in place, we can now use
this to pass information about the load addresses and names of each
loadables to ATF: now we can load the M0 firmware into DRAM and avoid
overwriting parts of the SPL stage. This is achieved by changing our
.its-file to use an available area of DRAM as the load-address.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This tracks the SPL changes for ATF for the Firefly:
* renames ATF_SUPPORT to ATF
* drops CONFIG_SPL_ATF_TEXT_BASE
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Having CONFIG_SPL_ATF seems more natural.
Rename it, while it it is easy and there's few boards that use it
(only RK3399 and RK3368 boards).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a new interface spl_invoke_atf() that takes a spl_image_info
argument and then derives the necessary parameters for the ATF entry.
Based on the additional information recorded (into /fit-images) from
the FIT loadables, we can now easily locate the next boot stage.
We now pass a pointer to a FDT as the platform-specific parameter
pointer to ATF (so we don't run into the future headache of every
board/platform defining their own proprietary tag-structure), as
FDT access is already available in ATF.
With the necessary infrastructure in place, we can now update the
support for the ARM Trusted Firmware to dispatch into the
spl_invoke_atf function only if a IH_OS_ARM_TRUSTED_FIRMWARE image is
loaded.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If a FDT was loaded (e.g. to append it to U-Boot image), we store it's
address and record information for all loadables into this FDT. This
allows us to easily keep track of images for multiple privilege levels
(e.g. with ATF) or of firmware images preloaded into temporary
locations (e.g. PMU firmware that may overlap the SPL stage).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
During the loading of more complex FIT images (e.g. when the invoked
next stage needs to find additional firmware for a power-management
core... or if there are multiple images for different privilege levels
started in parallel), it is helpful to create a record of what images
are loaded where: if a FDT is loaded for one of the next stages, it
can be used to convey the status and location of loadables.
This adds a fdt_record_loadable() function that can be invoked to
record the status of each loadable below the /fit-images path.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To better support bootin through an ATF or OPTEE, we need to
streamline some of the logic for when the FDT is appended to an image:
depending on the image type, we'd like to append the FDT not at all
(the case for the OS boot), to the 'firmware' image (if it is a
U-Boot) or to one of the loadables (if the 'firmware' is an ATF, an
OPTEE, or some other image-type and U-Boot is listed in the
loadabled).
To achieve this goal, we drop the os_boot flag and track the type of
image loaded. If it is of type IH_OS_U_BOOT, we append the FDT.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Mainly a stylistic change: convert the load_addr and entry_point
fields of struct spl_image_info to uintptr_t (from ulong).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When loading a full U-Boot with detached device-tree using the SPL FIT
backend, we should store the address of the FDT loaded as part of the
SPL image info: this allows us to fixup the FDT with additional info
we may want to propagate onward.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To boot on ARMv8 systems with ARM Trusted Firmware, we need to
assemble an ATF-specific parameter structure and also provide the
address of the images started by ATF (e.g. BL3-3, which may be the
full U-Boot).
To allow us to identify an ARM Trusted Firmware contained in a FIT
image, this adds the necessary definitions.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As per ARC HS databook (see chapter 5.3.3.2) it is required to add
3 NOPs after each write to IC_IVIC which we do from now on.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Eugeniy Paltsev <paltsev@synopsys.com>
Currently slave cores will be kick-started even if we want
to dry run bootm which is not what we really want.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Eugeniy Paltsev <paltsev@synopsys.com>
MRC (Memory Reference Code) is a binary blob used to set up the SDRAM
controller on some Intel boards. Add a test for this feature.
With this test coverage on binman is back up to 100%.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a test for this feature. It allows SPL to hold a pointer to the
microcode block. This is used for 64-bit U-Boot on x86.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a main program so that the tests can be executed directly, without
going through the main binman program.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a test that the 'entry' module works with or without importlib.
The tests are numbered so that they are executed in the correct order.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is a little check at the top of entry.py which decides if importlib
is available. At present this has no test coverage. To add this we will
need to import the module twice, once with importlib and once without.
In preparation for allowing a test to control the importing of this
module, remove all global imports of the 'entry' module.
Signed-off-by: Simon Glass <sjg@chromium.org>
The tests were broken by two separate commits which adjusted the output
when boards are listed. Fix this by adding back a PowerPC board and
putting the name of each board in the test.
Fixes: b9f7d881 (powerpc, 5xx: remove some "5xx" remains)
Fixes: 8d7523c5 (buildman: Allow showing the list of boards with -n)
Signed-off-by: Simon Glass <sjg@chromium.org>
Accessing the network slows down the test and limits the environment in
which it can be run. Add an option to disable network tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
This script runs the tests but does not report failure. Also it always
returns an exit code of 0 even on failure.
Fix these problems by checking the result of each test.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present these tests use the same filename as patman. This adds
confusion when running all tests, since error messages look very similar.
In fact binman tries to run the wrong tests at present.
Rename the tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
These test programs are includedd as binary files in U-Boot to avoid
having to build them (and associated toolchain differences). Instructions
on building are in the files themselves, but it seems better to provide
a Makefile which can be manually run when desired.
Add a Makefile, separate from the normal build system, to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is a debugging option in the Makefile to allow people to figure out
which u-boot.dtsi files are used in the build. But is it not easy to use
since it only shows files it finds, not those it is looking for. Update it
and update the mention of it to the docs.
Signed-off-by: Simon Glass <sjg@chromium.org>
A few header files still have a definition of CONFIG_ENV_SIZE, causing
warnings during buildman runs. This removes the duplicate definitions
from evb_px5.h, geekbox.h and rv1108_common.h.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Rockchip bootrom will enter download mode if it returns from
spl/tpl with a non-zero value and couldn't find a valid image
in the backup partition.
This patch provide a method to instruct the system to back to
bootrom download mode by checking the BROM_DOWNLOAD_FLAG register.
As the bootrom download function relys on some modules such as
interrupts, so we need to back to bootrom as early as possbile
before the tpl/spl code override the interrupt configurations.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
setup_boot_mode function use the same logic but different
mode register address across all the rockchip platforms,
so it's better to make this function reused across all the
platforms, and let the mode register address setting from
the config file.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
After applying the merged sysreset driver, there are build failures
due to an out-of-sync Makefile. This updates drivers/sysreset/Makefile
to address these build failures.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
With all targets converted to generate prepadded images, this removes
the spl_boot0 field from our config structure and removes the unused
code-path (for images that are not prepadded): i.e. spl_boot0 is now
implied as 'true' and the code is specialised by removing the other
case.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
There still are a few CONFIG_SPL_* options selected using defines from
rk3188_common.h instead of via Kconfig. This migrates those over to
Kconfig.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The BROM supports forcing it to enter download-mode, if an appropriate
result/cmd-word is returned to it. There already is a series to
support this in review, so this prepares the (newly C-version) of the
back-to-bootrom code to accept a cmd to passed on to the BROM.
All the existing call-sites are adjusted to match the changed function
signature.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
For the RK3188, the BROM will attempt to load up the first stage
image (SPL for the RK3188) in two steps: first 1KB to offset 0x800
in the SRAM and then the remainder to offset 0xc00 in the SRAM.
It always enters at 0x804, though.
With this changeset, the RK3188 boot removes the TPL (stub) stage and
builds a single SPL binary that utilizes the early back-to-bootrom via
the boot0-hook.
Consequently, the passing of the saved boot params via pmu->os_reg[2]
is also removed.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The back-to-bootrom implementation for Rockchip has always relied on
the stack-pointer being valid on entry, so there was little reason to
have this as an assembly implementation.
This provides a new C-only implementation of save_boot_params and
back_to_bootrom (relying on setjmp/longjmp) and removes the older
assembly-only implementation.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
The previous setjmp-implementation (as a static inline function that
contained an 'asm volatile' sequence) was extremely fragile: (some
versions of) GCC optimised the set of registers. One critical example
was the removal of 'r9' from the clobber list, if -ffixed-reg9 was
supplied.
To increase robustness and ensure PCS-compliant behaviour, the setjmp
and longjmp implementation are now in assembly and closely match what
one would expect to find in a libc implementation.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
As no '.type' was set for save_boot_params_ret in start.S, binutils
did not track whether it was emitted as A32 or T32. By properly
marking save_boot_params_ret as a potential function entry, we can
make sure that the compiler will insert the appropriate instructions
for branching to save_boot_params_ret both for call-sites emitted as
A32 and T32.
Reported-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
The save_boot_params_ret() prototype (for those of us, that have a
valid SP on entry and can implement save_boot_params() in C), was
previously only defined for !defined(CONFIG_ARM64).
This moves the declaration to a common block to ensure the prototype
is available to everyone that might need it.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
Some Rockchip BROM versions (e.g. the RK3188 and RK3066) first read 1KB data
from NAND into SRAM and executes it. Then, following a return to bootrom, the
BROM loads additional code to SRAM (not overwriting the first block read) and
reenters at the same address as the first time.
To support booting either a TPL (on the RK3066) or SPL (on the RK3188) using
this model of having to count entries, this commit adds code to the boot0
hook to track the number of entries and handle them accordingly.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
This updates the BCM281xx boot0-hook to the updated boot0 semantics
by emitting _start and the vector table before the boot0 hook (as
was the case before).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This updates the BCM235xx boot0-hook to the updated boot0 semantics
by emitting _start and the vector table before the boot0 hook (as
was the case before).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Version-changes: 5
- ran 'whitespace-cleanup'
With the updated boot0 semantics (i.e. giving the boot0-hook control
over when and where the vector table is emitted), the boot0-hook for
the socfpga needs to be adjusted.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
With the boot0-hook inserting the additional padding to receive our
SPL magic, the SPL_TEXT_BASE can be aligned again.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable the spl_boot0 in SPL and use the pre-padding TAG memory,
the mkimage do not need to pad it but only need to replace the value
with correct TAG value.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[Updated:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Rockchip SoCs bootrom design is like this:
- First 2KB or 4KB internal memory is for bootrom stack and heap;
- Then the first 4-byte suppose to be a TAG like 'RK33';
- The the following memory address end with '0004' is the first
instruction load and running by bootrom;
Let's use the boot0 hook to reserve the first 4-byte tag for all
the Rockchip SoCs.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Commit message taken from an older patch by:]
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The '_start' is using as vector table base address, and will write
to VBAR register, so it needs to be aligned to 0x20 for armv7.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[Updated to current code base:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The boot0 hook on ARM does not insert its payload before the vector
table. This is both a mismatch with thec comment above it and
contradict usage of the boot0 hook on ARM64.
To fix this (and unify the semantics for ARM and ARM64), we change the
boot0-hook semantics on ARM to match those on ARM64:
(1) if a boot0-hook is present it is inserted at the start of
the image
(2) if a boot0-hook is present, emitting the ARM vector table
(and the _start) symbol are suppressed in vectors.S and
the boot0-hook has full control over where and when it
wants to emit these
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Configure thermal configs to remain set by default for dra7xx and am57xx
devices.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The dra7xx series of SOCs contain a temperature sensor and an
associated analog-to-digital converter (ADC) which produces
an output which is proportional to the SOC temperature.
Add support for this temperature sensor.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Old url currently returns 403; modify to url that actually works
with current state of the list server
Signed-off-by: S. Lockwood-Childs <sjl@vctlabs.com>
With commit 84d46e7e89 ("tools: env: allow to print U-Boot version")
the fw_env utilities need the version.h header file. Building only
the envtools in a pristine build directory will fail due to missing
header files.
Make sure the header files are a dependency of the envtools target.
Fixes: 84d46e7e89 ("tools: env: allow to print U-Boot version")
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When building on a multi-core machine for an SPL-enabled board that
also uses CONFIG_OF_EMBED, the following error can be encountered
due to a race condition:
make[3]: *** No rule to make target 'spl/dts/dt.dtb.o', needed by
'spl/dts/built-in.o'. Stop.
../scripts/Makefile.spl:364: recipe for target 'spl/dts' failed
make[2]: *** [spl/dts] Error 2
make[2]: *** Waiting for unfinished jobs....
A reliable way to trigger this race condition is to add "sleep 60" to
the end of the "arch-dtbs" rule's recipe in "dts/Makefile" and to build
U-Boot against a board which uses the CONFIG_OF_EMBED and CONFIG_SPL
options using "make -j8" or a similar command.
This commit corrects this race condition via the use of CONFIG_OF_EMBED
in the same way that commit 3c00a2c8b5 ("Makefile: Correct dependency
race condition with TPL") and commit 054b3a1e80 ("dm: Makefile: Build
of-platdata before SPL") use CONFIG_OF_SEPARATE.
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
0 is not a pointer. So do not compare pointers to 0.
Do not return 0 from functions with a pointer return
type.
Problem identified with Coccinelle.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add some useful static code analysis scripts for coccinelle
copied from the Linux kernel v4.14-rc8:
Warn on check against NULL before calling free.
scripts/coccinelle/free/ifnullfree.cocci
Detect superfluous NULL check for list iterator.
scripts/coccinelle/iterators/itnull.cocci
Check if list iterator is reassigned.
scripts/coccinelle/iterators/list_entry_update.cocci
Check if list iterator is used after loop.
scripts/coccinelle/iterators/use_after_iter.cocci
Find wrong argument of sizeof in allocation function:
scripts/coccinelle/misc/badty.cocci
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Coccinelle is a program for static code analysis.
For details on Coccinelle see
http://coccinelle.lip6.fr/
Add scripts/coccicheck copied from Linux kernel v4.14.
The coccicheck script executes the tests *.cocci in
directory scripts/coccinelle by calling spatch.
In Makefile add a coccicheck target. You can use it with
make coccicheck MODE=<mode>
where mode in patch, report, context, org.
Add a copy of Linux v4.14 file Documentation/dev-tools/coccinelle.rst
as doc/README.coccinelle.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The iterator variable of list_for_each is never NULL.
if (1 || A) is always true.
Use break if entry found.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
As per current android recommendation
https://source.android.com/devices/architecture/kernel/modular-kernels
1. Android recovery mode should contain both SOC and ODM
kernel modules in the recovery partition.
2. If a kernel module is required both in recovery and normal boot
mode, the module has to be located in recovery and vendor
partition seperately.
3. Kernel modules used in recovery mode should be independent
of vendor and odm partition
4. Recovery image should contain atleast
storage, display, keypad, battery and pmic modules.
Due to these requirements, recovery image size has increased
to >10MB.
This patch is to increase recovery partition size for TI devices
so that we dont see such flashing error
log:
sending 'recovery' (12560 KB)...
OKAY [ 0.436s]
writing 'recovery'...
FAILED (remote: too large for partition)
finished. total time: 0.458s
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
ld --version | scripts/ld-version.sh
fails with
awk: scripts/ld-version.sh:
line 4: regular expression compile failed (missing '(')
.*)
So let's refresh the script from Linux kernel v4.14-rc8.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
sym_arr is of type struct symbol **.
So in malloc we need sizeof(struct symbol *).
The problem was indicated by coccinelle.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add a driver for the I2C controller available on Amlogic Meson SoCs.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Currently the MX6QDL option is selected via CONFIG_SYS_EXTRA_OPTIONS,
but it is better to select it directly via Kconfig.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
The VPD data is used on a number of GE products. Move the parsing code to
a common location so that we can share this code.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Acked-by: Stefano Babic <sbabic@denx.de>
Add support for bootcounter on an EXT filesystem.
Sync configuration whitelist.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Some fixes when reading EXT files and directory entries were identified
after using e2fuzz to corrupt an EXT3 filesystem:
- Stop reading directory entries if the offset becomes badly aligned.
- Avoid overwriting memory by clamping the length used to zero the buffer
in ext4fs_read_file. Also sanity check blocksize.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Reviewed-by: Stefano Babic <sbabic@denx.de>
This reverts commit b8b9790e23.
Some wandboard variants no longer boot after this commit, so keep
the original delay to avoid the boot regression.
Reported-by: Varga Zsolt <vazso@vazso.hu>
Tested-by: Varga Zsolt <vazso@vazso.hu>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Command run setup_emmc will create gpt partitions for mmc 0 device
based on patitions variable.
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Change dfu_alt_info variable to use the following altsetting:
uboot: To flash raw U-Boot
/zImage: boot: To copy kernel image
/imx6ul-pico-hobbit.dtb: To copy dtb file
rootfs: To copy rootfs
List the currently attached DFU capable USB devices running:
sudo dfu-util -l
Flash U-Boot:
sudo dfu-util -D u-boot.imx -a uboot
Copy boot files:
sudo dfu-util -D zImage -a /zImage
sudo dfu-util -D imx6ul-pico-hobbit.dtb -a /imx6ul-pico-hobbit.dtb
Flash rootfs:
sudo dfu-util -D rootfs.ext4 -a rootfs
To copy boot files you need to have a formated mmc 0:1 partition. To
format with ext4 filesystem you can use ums.
Run on target:
ums 0 mmc 0
and on host:
sudo mkfs.ext4 /dev/sdx1
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Currently the rootfs location is passed via mmcblk number and using
the UUID method to specify the rootfs location is a better approach
working even if mmcblk number for the eMMC changes depending on the
kernel versions.
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
We first introduce CONFIG_USE_BOOTCOMMAND, similar to
CONFIG_USE_BOOTARGS. We then migrate CONFIG_BOOTCOMMAND for most
CONFIG_DISTRO_DEFAULT users. In some cases platforms have a complex
scheme around this usage, and these have been defered for the moment so
that platform maintainers can work on a migration plan.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Since CONFIG_DEFAULT_CONSOLE is already started with "console=",
the console argument in CONFIG_EXTRA_ENV_SETTINGS is expanded to
"console=console=ttySAC1,115200n8" and this causes the wrong
console device.
#define CONFIG_DEFAULT_CONSOLE "console=ttySAC1,115200n8\0"
...
#define CONFIG_EXTRA_ENV_SETTINGS \
"console=" CONFIG_DEFAULT_CONSOLE
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
UARTs 1 through 5 were missing in the code - added.
Also pick the default according to the configuration setting for the
console index.
Signed-off-by: Ronald Landheer-Cieslak <ronaldlandheercieslak@eaton.com>
This patch is to change U-Boot PCI bus assignement compliant with Linux.
It means each PCIe controller's bus number is 0, not the current maximum
PCI bus number, when start to scan this controller.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
While commit 36d35345b1 ("tpm: add missing va_end") added
some missing calls to va_end(), it missed a few places.
Signed-off-by: André Draszik <adraszik@tycoint.com>
Acked-by: Simon Glass <sjg@chromium.org>
TPM_NV_PER_PPREAD: physical presence needed for reading
TPM_NV_PER_WRITEDEFINE: persistent write lock by writing size 0
TPM_NV_PER_WRITEALL: write in one go
Signed-off-by: André Draszik <adraszik@tycoint.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a function to obtain random data from the TPM.
Signed-off-by: André Draszik <adraszik@tycoint.com>
Added commit message, add cast to min()
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Allow the platform to define a partition by name at the end of which
the environment data will be located.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
In U-boot, serial_tstc was use to determine is there have a character in
serial console that pending for read. If there is no "pending" function
implemented in serial driver, the serial-uclass will return "true(1)"
to indicate there have a character pending to read.
Thus, read a character from nulldev serial will result in continuous
getting -EAGAIN return which might lead system to hang.
This commit is to fix a bug in nulldev serial which implement "pending"
function in nulldev serial to always indicate there is no character in
console that pending for read.
Signed-off-by: Wilson Lee <wilson.lee@ni.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Keng Soon Cheah <keng.soon.cheah@ni.com>
Cc: Chen Yee Chew <chen.yee.chew@ni.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
This is required in the case where U-Boot is typically loaded and run at
a particular address, but for some reason the RAM at that location is not
available, e.g. due to memory fragmentation loading other boot binaries or
firmware, splitting an SMP complex between various different OSs without
using e.g. the EL2 second-stage page tables to hide the memory asignments,
or due to known ECC failures.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
It can be useful to record how long tests take; this can help debug slow
running test systems or track changes in performance over time. Enhance
the test system to record timestamps while running test:
- Whenever a new log file section is started.
- After U-Boot is started and communication has been established.
- After each host or U-Boot command is executed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Fix clock division factor initialization for RCC_PLLCFGR
registers.
PLLR bits (bit 31-28) in RCC_PLLCFGR must not be cleared,
it's a forbidden value. So update RCC_PLLCFGR using
clrsetbits_le32() to set only necessary bits fields.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert this driver to driver model.
This driver is also used by VEXPRESS platforms which doesn't
use driver model.
Tested on STM32F746 and STM32F769 platforms.
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Update arm_pl180_mmci_init() prototype by adding struct mmc**
param. This is needed before converting this driver to driver model
in order to use arm_pl180_mmci_init() in driver model and in none
driver model implementation
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This option provides better performance and should really always be
enabled. Make this be default y.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Jeroen Hofstee <jeroen@myspectrum.nl>
This patch adds support for the Internal RMII Ethernet PHY on the
Amlogic P212 Reference Board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
On Amlogic Meson GXL/GXM, supplementary ethernet configuration registers
were added to configure the internal RMII PHY interface.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY.
The PHY acts as a generic PHY but needs a slight configuration right
before it's configuration.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
lib/libfdt/ and scripts/dtc/libfdt have the same copies for the
followings 6 files:
fdt.c fdt_addresses.c fdt_empty_tree.c fdt_overlay.c fdt_strerr.c
fdt_sw.c
Make them a wrapper of scripts/dtc/libfdt/*. This is exactly what
Linux does to sync libfdt. In order to make is possible, import
<linux/libfdt.h> and <linux/libfdt_env.h> from Linux 4.14-rc5.
Unfortunately, U-Boot locally modified the following 3 files:
fdt_ro.c fdt_wip.c fdt_rw.c
The fdt_region.c is U-Boot own file.
I did not touch them in order to avoid unpredictable impact.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add this typedef in the same place as in Linux. This is necessary
to refactor libfdt inclusion.
U-Boot also defines it in include/compiler.h. Of course it should
not do that, but I do not want to open a can of worms.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Prior to this commit, tools/Makefile pulls all libfdt files from
lib/libfdt.
lib/libfdt/ and scripts/dtc/libfdt have the same copies for the
followings 6 files:
fdt.c fdt_addresses.c fdt_empty_tree.c fdt_overlay.c fdt_strerr.c
fdt_sw.c
This commit changes them to #include ones from scripts/dtc/libfdt.
Unfortunately, U-Boot locally modified the following 3 files:
fdt_ro.c fdt_wip.c fdt_rw.c
I did not touch them in order to avoid unpredictable impact.
The fdt_region.c is U-Boot own file. This is also borrowed from
lib/libfdt/.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fortunately, U-Boot did not modify libfdt_internal.h locally.
Change it to a wrapper of scripts/dtc/libfdt/fdt.h, which will be
periodically synced with the upstream DTC (or kernel).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fortunately, U-Boot did not modify fdt.h locally.
Change it to a wrapper of scripts/dtc/libfdt/fdt.h, which will be
periodically synced with the upstream DTC (or kernel).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, pylibfdt is always compiled if swig is installed on your
machine. It is really annoying because most of targets (excepts
x86, sunxi, rockchip) do not use dtoc or binman.
"checkbinman" and "checkdtoc" are wrong. It is odd that the final
build stage checks if we have built necessary tools. If your platform
depends on dtoc/binman, you must be able to build pylibfdt. If swig
is not installed, it should fail immediately.
I added PYLIBFDT, DTOC, BINMAN entries to Kconfig. They should be
property select:ed by platforms that need them. Kbuild will descend
into scripts/dtc/pylibfdt/ only when CONFIG_PYLIBFDT is enabled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The pylibfdt is used by dtoc (and, indirectly by binman), but there
is no reason why it must be generated in the tools/ directory.
Recently, U-Boot switched over to the bundled DTC, and the directory
structure under scripts/dtc/ now mirrors the upstream DTC project.
So, scripts/dtc/pylibfdt is the best location.
I also rewrote the Makefile in a cleaner Kbuild style.
The scripts from the upstream have been moved as follows:
lib/libfdt/pylibfdt/setup.py -> scripts/dtc/pylibfdt/setup.py
lib/libfdt/pylibfdt/libfdt.i -> scripts/dtc/pylibfdt/libfdt.i_shipped
The .i_shipped is coped to .i during building because the .i must be
located in the objtree when we build it out of tree.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This adds the following commits from upstream:
b1a6003 tests: Add a test for overlays syntactic sugar
737b2df overlay: Add syntactic sugar version of overlays
497432f checks: Use proper format modifier for size_t
22a65c5 dtc: Bump version to v1.4.5
c575d80 Add fdtoverlay to .gitignore
b6a6f94 fdtoverlay: Sanity check blob size
8c1eb15 pylibfdt: Use Python2 explicitly
ee3d26f checks: add interrupts property check
c1e7738 checks: add gpio binding properties check
b3bbac0 checks: add phandle with arg property checks
[ sync with Linux commit: 4201d057ea91c3d6efd2db65219bc91fae413bc2 ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
libfdt has gained some new files. We need to include them in the
kernel's copy.
Reported-by: Kyle Yan <kyan@codeaurora.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[ Linux commit: 4322323058f010274564006d61945187a15b6361 ]
This adds platform code for the Amlogic P212 reference board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.
This initial submission only supports UART and MMC/SDCard, support for the
internal Ethernet PHY in Work In Progress.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Beniamino Galvani <b.galvani@gmail.com>
Add the Amlogic Meson GXL pinctrl support based on the GXBB driver and
the synchronized DTS from Linux 4.13.5
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Beniamino Galvani <b.galvani@gmail.com>
Synchronize the Amlogic ARM64 dts from mainline Linux 4.13.5
In the preparation of the support of the Amlogic P212 board,
import the corresponding meson-gxl-s905x-p212.dts file.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Beniamino Galvani <b.galvani@gmail.com>
All regulators are hooked to EN_Pin at reset so that EN Pin controls
their state. Hook the LDO1 regulator to EN pin which at reset is not
hooked. This applies only to LP8733.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
For the DM TPS65910 driver I'm working on, querying the MPU voltage
should return a value in uV. This value can then be used by the
regulator's standard function set_value to set the MPU voltage.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The offset of the permanent flags structure is in a different
place in the response compared to what the code is doing,
which gives us a completely useless result.
Fix by replacing hand-crafted code with generic parser
infrastructure.
Signed-off-by: André Draszik <adraszik@tycoint.com>
Acked-by: Simon Glass <sjg@chromium.org>
The maximum length of the name of the image is
obviously not sizeof(), which is just the
length of a pointer, but IH_NMLEN.
fixes: 62cf11c092
("SPL: Limit image name print length")
Signed-off-by: André Draszik <adraszik@tycoint.com>
Acked-by: Simon Glass <sjg@chromium.org>
This currently causes a warning in sandbox and will not do the right
thing:
drivers/core/read.c: In function ‘dev_read_addr_ptr’:
drivers/core/read.c:64:44: warning: cast to pointer from integer of
different size [-Wint-to-pointer-cast]
return (addr == FDT_ADDR_T_NONE) ? NULL : (void *)addr;
Use map_sysmem() which is the correct way to convert an address to a
pointer.
Fixes: c131c8bca8 (dm: core: add dev_read_addr_ptr())
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Since the compiler is free to place a char array to any address in
memory (in this case the stack), also to a non word aligned address the
function "fdt_prop_parse" runs into troubles upon it wants to write some
(fdt32_t *) to such a variable (if it has been placed to a none word
aligned address).
To avoid this we tell the compiler to always align this scratchpad to a
word aligned address.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Simon Glass <sjg@chromium.org>
All current ClearFog SOMs have the SPI flash populated. Enable SPI flash in
the device tree.
Add an alias to the SPI bus so that the 'sf' command can probe the flash on
bus 1.
Add the "spi-flash" compatible string to make the standard SPI flash driver
probe the device.
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
The production variant of the SPI flash used by the clearfog
devices are based on winbond chips. Additionally enable
SPI_FLASH_BAR since some variants will have 16MB of flash
that requires this to be enabled.
Remove the default speed and mode; these values are taken from the
device tree when CONFIG_DM_SPI_FLASH is enabled.
Add default bus, so that 'sf' detects the SPI flash by default.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: remove speed/mode; add bus; move winbond to defconfig]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable the driver by default for the clearfog boards since the external
port is configured for XHCI.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: split from the SoC setup patch]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
This fixes the USB 3.0 support for the a38x SOC.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: use fdt_addr_t]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
This makes the initial changes need to support the
a38x series of SOCs. It adds the device-tree identifier
as well as changing the board_support function to take
the IO address designated by device-tree.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: use fdt_addr_t; update 37xx and 8K implementations]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable DISTRO_DEFAULTS for
mvebu_db_armada8k_defconfig
mvebu_mcbin-88f8040_defconfig
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The board uses T-topology for the four x16 DRAM chips, so remove
the write-leveling from the SPL as that is only usefly on fly-by
topology and can be harmful on T-topology. Also update the DRAM
timing with values from calibration on multiple boards.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Update help message for "mac" command to reflect correct descriptions
and parameters.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Value provided in MC_MEM_SIZE_ENV_VAR is in hex. Use 16 as base
in simple_strtoul.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Distro boot support gives flexibility to run distro RFS like Ubuntu
being deployed from SD card or SATA drive. If it fails to detect
external storage, fall back to qspi/sd boot.
Enable this by default in RDB's defconfig by selecting
CONFIG_DISTRO_DEFAULTS
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Zhang Ying <zhangying@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Currently the chipselect used to identify the corresponding NAND chip
is stored at the controller and only set during fsl_ifc_chip_init().
This way, only the last NAND chip is working, as the previous value
of cs_nand gets overwritten.
In order to solve this issue the chipselect is computed on demand by
evaluating the bank variable. Thus, the correct chipselect for each
NAND chip operation is used.
Tested on hardware with two NAND chips connected to the IFC
controller.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Scott Wood <oss@buserror.net>
[YS: reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
The zero value returned from qbman_swp_acquire() is an error
condition meaning no free buffer for allocation.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Kushwaha Prabhakar <prabhakar@freescale.com>
[YS: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-11-14 08:33:20 -08:00
869 changed files with 27122 additions and 23976 deletions
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
