mirror of
https://source.denx.de/u-boot/u-boot.git
synced 2026-06-13 15:03:58 +03:00
2a00d73d08
Make the raw-mode options depend on SPL_SYS_MMCSD_RAW_MODE in a more direct way. This makes it easier to understand the options with 'make menuconfig'. There are three different ways of specifying the offset: - sector offset - partition number - partition type So make these a choice, so it is more obvious what is going on. Update existing boards to enable SPL_SYS_MMCSD_RAW_MODE where needed. Reviewed-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de> Signed-off-by: Simon Glass <sjg@chromium.org>
34 lines
1.3 KiB
Plaintext
34 lines
1.3 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_ARCH_OMAP2PLUS=y
|
|
CONFIG_SYS_MALLOC_F_LEN=0x4000
|
|
CONFIG_DEFAULT_DEVICE_TREE="ti/omap/omap3-sniper"
|
|
CONFIG_TARGET_SNIPER=y
|
|
CONFIG_SPL_SYS_MALLOC_F_LEN=0x400
|
|
CONFIG_SPL=y
|
|
CONFIG_DISTRO_DEFAULTS=y
|
|
CONFIG_BOOTCOMMAND="setenv boot_mmc_part ${kernel_mmc_part}; if test reboot-${reboot-mode} = reboot-r; then echo recovery; setenv boot_mmc_part ${recovery_mmc_part}; fi; if test reboot-${reboot-mode} = reboot-b; then echo fastboot; fastboot 0; fi; part start mmc ${boot_mmc_dev} ${boot_mmc_part} boot_mmc_start; part size mmc ${boot_mmc_dev} ${boot_mmc_part} boot_mmc_size; mmc dev ${boot_mmc_dev}; mmc read ${kernel_addr_r} ${boot_mmc_start} ${boot_mmc_size} && bootm ${kernel_addr_r};"
|
|
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
|
|
CONFIG_SPL_BOARD_INIT=y
|
|
CONFIG_SPL_SYS_MALLOC_SIMPLE=y
|
|
CONFIG_SPL_SYS_MALLOC=y
|
|
CONFIG_SPL_SYS_MALLOC_SIZE=0x800000
|
|
# CONFIG_SPL_SYS_MMCSD_RAW_MODE is not set
|
|
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
|
|
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=2
|
|
# CONFIG_SPL_FS_EXT4 is not set
|
|
# CONFIG_SPL_NAND_SUPPORT is not set
|
|
CONFIG_CMD_GPIO=y
|
|
CONFIG_CMD_I2C=y
|
|
CONFIG_CMD_MMC=y
|
|
# CONFIG_CMD_SETEXPR is not set
|
|
CONFIG_OF_CONTROL=y
|
|
CONFIG_SPL_OF_CONTROL=y
|
|
CONFIG_OF_UPSTREAM=y
|
|
CONFIG_ENV_OVERWRITE=y
|
|
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_SPL_DM=y
|
|
CONFIG_DM_I2C=y
|
|
CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
|
|
CONFIG_TWL4030_INPUT=y
|
|
CONFIG_MMC_OMAP_HS=y
|