arch: arm: dts: k3-am625-phyboard-lyra: Drop bootph properties

Remove bootph properties no longer needed. These are now handled
in upstream Linux device trees.

Signed-off-by: Wadim Egorov <w.egorov@phytec.de>

arch/arm/dts/k3-am625-phyboard-lyra-rdk-u-boot.dtsi

@@ -19,36 +19,16 @@
 		mmc0 = &sdhci0;
 		mmc1 = &sdhci1;
 	};
-
-	memory@80000000 {
-		bootph-all;
-	};
-};
-
-&cpsw3g {
-	bootph-all;
-};
-
-&cpsw_port1 {
-	bootph-all;
 };
 
 &cpsw_port2 {
 	status = "disabled";
 };
 
-&cpsw3g_phy1 {
-	bootph-all;
-};
-
 &phy_gmii_sel {
 	bootph-all;
 };
 
-&fss {
-	bootph-all;
-};
-
 &main_bcdma {
 	bootph-all;
 	reg = <0x00 0x485c0100 0x00 0x100>,
@@ -63,38 +43,6 @@
 		    "ringrt" , "cfg", "tchan", "rchan";
 };
 
-&main_gpio0 {
-	bootph-all;
-};
-
-&main_mdio1_pins_default {
-	bootph-all;
-};
-
-&main_i2c0 {
-	bootph-all;
-};
-
-&main_i2c0_pins_default {
-	bootph-all;
-};
-
-&main_mmc0_pins_default {
-	bootph-all;
-};
-
-&main_mmc1_pins_default {
-	bootph-all;
-};
-
-&main_pktdma {
-	bootph-all;
-};
-
-&main_rgmii1_pins_default {
-	bootph-all;
-};
-
 &main_rti1 {
 	status = "disabled";
 };
@@ -111,27 +59,8 @@
 	status = "disabled";
 };
 
-&main_uart0 {
-	bootph-all;
-};
-
-&main_uart0_pins_default {
-	bootph-all;
-};
-
-&main_uart1 {
-	bootph-all;
-};
-
-&main_uart1_pins_default {
-	bootph-all;
-};
-
 &ospi0 {
-	bootph-all;
-
 	flash@0 {
-		bootph-all;
 		partitions {
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
@@ -161,43 +90,14 @@
 	};
 };
 
-&ospi0_pins_default {
-	bootph-all;
-};
-
-&sdhci0 {
-	bootph-all;
-};
-
-&sdhci1 {
-	bootph-all;
-};
-
-&usbss0 {
-	bootph-all;
-};
-
 &usb0 {
 	dr_mode = "peripheral";
-	bootph-all;
 };
 
 &usb0_phy_ctrl {
 	bootph-all;
 };
 
-&vcc_3v3_mmc {
-	bootph-all;
-};
-
-&vcc_5v0_som {
-	bootph-all;
-};
-
-&vddshv5_sdio {
-	bootph-all;
-};
-
 &wkup_uart0 {
 	bootph-all;
 };

arch/arm/dts/k3-am625-r5-phycore-som-2gb.dts

@@ -93,14 +93,6 @@
 	ti,sci = <&dm_tifs>;
 };
 
-/* Main UART1 is used for TIFS firmware logs */
-&main_uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&main_uart1_pins_default>;
-	status = "okay";
-	bootph-pre-ram;
-};
-
 &mcu_pmx0 {
 	wkup_uart0_pins_default: wkup-uart0-pins-default {
 		pinctrl-single,pins = <