Use list_for_each_entry_safe and comparisons against the current and
next efi_mem_desc. This reduces the computation required for merging
regions, prevents unnecessary additional iterations of the list, and
requires less temporary values.
Signed-off-by: Randolph Sapp <rs@ti.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Check for duplicate memory mappings before reporting any incorrect
attributes. Could be that second allocation has the correct type while
the first doesn't. Knowing there is a duplicate in this scenario is
more helpful than just reporting the first mismatch.
Signed-off-by: Randolph Sapp <rs@ti.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the allocation flags inline documentation to follow the kernel
object like macro documentation specification.
Use active voice for the short descriptions.
Signed-off-by: Randolph Sapp <rs@ti.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The number EFICONFIG_ENTRY_NUM_MAX - 1 must be printable
to field key of struct eficonfig_entry.
Fixes: 1f0583beeb ("eficonfig: set EFICONFIG_ENTRY_NUM_MAX to INT_MAX - 1")
Fixes: 23aa0502a4 ("eficonfig: increase the number of menu entries")
Addresses-Coverity-ID: 583414 - Out-of-bounds write
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
When using lwIP, efi_dp_from_http() may fail to initialize ip or mask.
Initialize the variables before the call.
Addresses-Coverity-ID: 645840 - Uninitialized variables (UNINIT)
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The R-Car Gen5 SoCs contains Cortex-M33, Cortex-R52 and Cortex-A720AE
cores. Add U-Boot build options for the Cortex-M33 core.
Since the Cortex-M33 core is a 32bit core, select V8M and ARM64 for
RCAR64 accordingly. Select TMU timer on the 32bit core, where it is
used instead of the ARMv8 timer. Adjust TMU timer base address to match
the address map of the Cortex-M33 core. Disable unused OF_BOARD_SETUP
as well as unavailable POSITION_INDEPENDENT configuration options.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Add support of Renesas R-Car Gen5 window watchdog timer. Timeout
configuration is derived from CONFIG_WATCHDOG_TIMEOUT_MSECS, which
is more accurate than the 1-second granularity 'timeout' passed to
.start callback.
Reviewed-by: Stefan Roese <stefan.roese@mailbox.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add R-Car Gen5 RSIP controller remoteproc driver capable of starting
the SCP, Cortex-R52 and Cortex-A720 cores in Renesas R-Car R8A78000
X5H SoC. The SCP core is started by releasing the core from reset,
the Cortex-R52 and Cortex-A720 are started using the SCP SCMI call.
The entry point for SCP core is fixed to its STCM, entry points for
Cortex-R52 and Cortex-A720 are set during rproc load.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Both R-Car V3M Eagle and V3MSK U-Boot DT extras contain AVB pinmux
assignment, which is a leftover from before the same pinmux was part
of upstream DTs. Remove the duplicate AVB pinmux assignment in favor
of the upstream DT content. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Remove duplicate properties which are present both in arch/arm/dts/
and upstream dts/upstream/src/arm64/renesas/ in favor of those in
upstream DTs. Since those are duplicates, this causes no functional
change. Remove unused num-cs and bank-width DT properties.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
If fat_sect_size = 0 and nr_sect = 0, the value of ret is never initialized.
A random return value is returned.
Initialize ret to 0.
Addresses-Coverity-ID: - 645495 Uninitialized scalar variable
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is a value of 256K hardcoded as u-boot image size. This
produce bank tty as soon as the image size grows over the limit.
Fix it by using value preset by CONFIG_SYS_MONITOR_LEN.
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
Some NXP imx hardware ip module as the esdhc controller are exactly the
same in some new ColdFire cpus. For the specific case, mcf5441x needs to
use the existing fsl_esdhc_imx.c driver for the esdhc device.
Create a stub to be able to use NXP "imx" serie drivers as the
fsl_esdhc_imx in the ColdFire architecture.
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
Allow cpu families as mcf5441x (m68k) to use the fsl_esdhc_imx driver
since the hardware ip module is the same.
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
---
Changes in v2:
- moved before menuconfig changes
Add mmc support for the mcf5441x family. There is only one esdhc
controller for this cpu family.
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
probe_ram_size_by_alias() detects whether a probe address still aliases
a lower address by writing through one address and reading through the
other.
On i.MX95 this occasionally reported a false non-alias when the alias
read happened immediately after the write.
A memory barrier alone, mb(), was tested but did not make the failure go
away. This suggests that ordering the CPU accesses is not sufficient for
this probe, likely because the issue is in the path to the memory
controller rather than in the core itself.
Read the written address back before checking the alias address. This
appears to force the write to become observable at the probe address
before using the alias read to decide whether the tested address range
exists.
If the readback does not match the written pattern, restore the saved
value and continue with the next check. This keeps the probe robust for
addresses that do not reliably retain the test pattern.
Fixes: 0977448b45 ("common: memsize: add RAM size probe based on alias detection")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rec_from_blob() function returns a pointer, but the code was
comparing it using "rec <= 0" which is incorrect for pointer types.
Pointers should be compared using "== NULL" or "!= NULL".
Addresses-Coverity-ID: CID 645841: Incorrect expression (BAD_COMPARE)
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Raymond Mao <raymondmaoca@gmail.com>
The fdt_pack() function can return an error code, but its return value
was not being checked. Add proper error handling to propagate any
failure.
Also fix typo in comment: "Shink" -> "Shrink".
Addresses-Coverity-ID: CID 645839: Error handling issues (CHECKED_RETURN)
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Raymond Mao <raymondmaoca@gmail.com>
With correct POSIX handling, unquoted empty variables can turn the
expression like
test -n ${fdtfile}
into
test -n
The POSIX handling for single argument `test` evaluates it as true,
so the fallback initialization will be skipped unexpectedly.
Quoting variable expansions in `test` expressions will always result in
correct behavior for empty and non-empty values.
This change was triggered by
commit 8b0619579b ("cmd: test: fix handling of single-argument form of test")
The aim is to have a less fragile codebase that is not dependent on a
quirk of the shell implementation.
Use quoted variable expansions in `test` expressions throughout.
Signed-off-by: Franz Schnyder <franz.schnyder@toradex.com>
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Apologies for the delay, but please pull those sunxi changes into
v2026.07. Nothing earth shattering, mostly minor improvements like
better SPL power LED support, and fixes to some H616 DRAM setup. Also
some more forward looking enhancement for the SPI code. I also pulled in
Richard's raw NAND flash improvements for the H6/H616 SoC, though this
lacks proper peer testing due to the lack of mainline support for any
board actually employing those chips.
No need to reset user data length registers in SPL.
In SPL, only the first user data length register is used, so we don't
need to reset all of them.
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
In Allwinner SoCs, user data can be added in OOB before each ECC data.
For older SoCs like A10, the user data size was the size of a register
(4 bytes) and was mandatory before each ECC step.
So, the A10 OOB Layout is:
[4Bytes USER_DATA_STEP0] [ECC_STEP0 bytes]
[4bytes USER_DATA_STEP1] [ECC_STEP1 bytes]
...
NB: the BBM is stored at the beginning of the USER_DATA_STEP0.
Now, for H6/H616 NAND flash controller, this user data can have a
different size for each step.
So, we are maximizing the user data length to use as many OOB bytes as
possible.
Fixes: 7d1de98011 ("mtd: rawnand: sunxi_spl: add support for H6/H616 nand controller")
Fixes: f163da5e6d ("mtd: rawnand: sunxi: add support for H6/H616 nand controller")
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
In sunxi_nand_chip_init there's quite a lot of kfree/return, it's easy
to forget a kfree(), so use a goto/kfree instead.
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
[Andre: rename goto label, keep return 0;]
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Formatting via clang-format is controlled by .clang-format.
For each statements should be formatted with a brace at the line end:
for_each() {
}
This requires clang-format to know that the symbol is not a function
but a for each macro. We use some for each macros which don't exist in
Linux. Add these to file .clang-format.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
In the past, we only had one network stack which was called NET. The
network features were enabled for the legacy (and then only) networking
stack since commit 22353fa6b5 ("bootstd: Add some default filesystems
and commands"). Then instead on relying on NET legacy stack for enabling
networking features, the dependencies were (mostly) changed to depend on
CMD_NET in commit a0c739c184 ("boot: Create a common BOOT_DEFAULTS for
distro and bootstd"). Then a new stack (lwIP) appeared, then CMD_NET was
made available with this new stack in commit 98ad145db6 ("net: lwip:
add DHCP support and dhcp commmand") making the networking features
possible to enable and finally commit f1e978fd54 ("boot: Update tests
around network symbols in BOOT_DEFAULTS_CMDS") made it explicit that we
need *a* network stack to enable some networking features.
Align the bootstd documentation with what's actually implemented as
Kconfig dependencies. Note that BOOTSTD_DEFAULTS selects BOOT_DEFAULTS
which selects BOOT_DEFAULTS_CMDS which then selects network features.
The CMDLINE symbol needs to be enabled as well for BOOT_DEFAULTS to
select BOOT_DEFAULTS_CMDS, but I don't think we need to go that far into
explaining what's required to enable some commands.
Reported-by: Simon Glass <sjg@chromium.org>
Closes: https://lore.kernel.org/u-boot/CAFLszTgZC1FGy8965pHiG-u=FhrguftRv41ghQ_Qb_RRXx6tyg@mail.gmail.com/
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
We cannot use .clang-format without modification. For instance U-Boot
has some for each macros that Linux does not have.
Adjust the description.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add fTPM support documentation including an overview, configuration
steps for RPMB provisioning, OP-TEE TA build instructions, and
verification procedure.
Signed-off-by: Shiva Tripathi <s-tripathi1@ti.com>
If efi_init_obj_list() fails we cannot use the UEFI sub-system.
* Instead of having messages for this everywhere write an error message
in efi_init_obj_list().
* Always use (ret != EFI_SUCCESS) when checking the return value of
efi_init_obj_list().
* Remove the return code from the error message as it does not help
users to understand which initialization went wrong.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add build steps for building U-Boot in secure state with
TF-A and OP-TEE. It includes the full steps for building
OP-TEE and TF-A to use with U-Boot. Also a short description
how to invoke QEMU with enabled EL3 and EL2. EL3 (machine
option secure=on) is required to run TF-A.
Signed-off-by: Johannes Krottmayer <krotti83@proton.me>
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
As exposed by "make randconfig", we have an issue with the dependencies
for EFI_HTTP_BOOT. As this is implemented by running commands (as seen
by what it selects) it must depend on CMDLINE as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
All of these platforms enable CONFIG_BOARD_EARLY_INIT_F and then have a
do-nothing board_early_init_f function. Change to not enabling the
option and so not needing an empty function.
Signed-off-by: Tom Rini <trini@konsulko.com>
In sunxi_nfc_hw_ecc_{read,write}_chunk(), the ECC step was force to 0,
the reason is not trivial to get when reading the code.
The explanation is that, from the NAND flash controller perspective, we
are indeed at step 0 for user data length and ECC errors.
Just add a const value with an explanation to clarify things.
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Reviewed-By: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
The user data length (4) used all over the code hard coded.
And sometimes, it's not that trivial to know that it's the user data
length and not something else.
Moreover, for the H6/H616 this value is no more fixed by hardware, but
could be modified.
Using a define here makes the code more readable.
Suggested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Once reset SPI TX or RX fifo, the underlying hardware need to take
some time to actually settle down, the two bits will automatically
clear to 0, so use a poll mechanism to check status bits to make sure
it's done correctly.
On Cubie A7A board which using A733 SoC, we encoutered a SPI nor flash
timeout issue, it turns out that the SPI fifo reset take a few time to
settle down, Add a loop to poll the status.
This was the error message shows on A7A board once this issue happened.
=> sf probe
ERROR: sun4i_spi: Timeout transferring data
Failed to initialize SPI flash at 0:0 (error -2)
Signed-off-by: Yixun Lan <dlan@gentoo.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
CONFIG_DRAM_SUNXI_TPR6 is the only DRAM config parameter that has a
non-zero default value. Since we need to provide a value for all the
other parameters anyway, avoiding TPR6 makes no real difference.
To make matters worse, TPR6 is a compound value covering multiple DRAM
types, but also spans over three SoCs, which makes it hard to find one
good default value.
Drop the default from Kconfig, and put some explicit values in the
defconfigs for the few boards that were relying on the default so far.
The value is taken from one BSP, only the lower byte matters anyway for
those boards, all using DDR3 DRAM.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Paul Kocialkowski <paulk@sys-base.io>
Allwinner's DRAM initialisation code defines a parameter named TPR6,
presumably containing some "Vref" parameter, but containing values for
*all* DRAM types. The runtime code selects one byte based on the DRAM
type used.
This selection code was wrong for LPDDR3, the value is encoded in
bits [23:16], not [15:8]. Fix that in the code, which also aligns it
with the very similar code for the A133 and A523.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reported-by: Philippe Simons <simons.philippe@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Paul Kocialkowski <paulk@sys-base.io>
