Set CONFIG_NR_DRAM_BANKS to 2 as we have two banks described in the
memory/ node for lower and higher addressible DDR regions.
This allows use of FDT functions from fdt_support.c to set up and fix up
the memory/ node correctly.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
The functionality of enabling Inline ECC is now controlled by
CONFIG_K3_INLINE_ECC. So, remove the support for 'ti,ecc-enable'
property to avoid redundancy and to ensure the Inline ECC feature is
mananged through build-time config.
Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Add CONFIG_K3_INLINE_ECC so that ECC functions can be compiled into R5 SPL
only when the config has been enabled.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Enable ECC 1-bit error, 2-bit error, multiple 1-bit error interrupts
by setting the respective bits in the DDRSS_V2A_INT_SET_REG register.
Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
Setup the ECC region's start and range using the device private data,
ddrss->ddr_bank_base[0] and ddrss->ddr_ram_size. Also, move start and
range of ECC regions from 32 bits to 64 bits to accommodate for
DDR greater than or equal to 4GB.
Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
As R5 is a 32 bit processor, the RAM banks' base and size calculation
is restricted to 32 bits, which results in wrong values if bank's base
is greater than 32 bits or bank's size is greater than or equal to 4GB.
So, add k3_ddrss_ddr_bank_base_size_calc() to get the base address and
size of RAM's banks from the device tree memory node, and store in a
64 bit device private data which can be used for ECC reserved memory
calculation, Setting ECC range and Fixing up bank size in device tree
when ECC is enabled.
Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
The 1-bit inline ECC support in TI's DDRSS bridge requires
the configured memory regions to be preloaded with a pattern
before use. This is done by the k3-ddrss driver from the
R5 SPL in a 'for' loop. It takes around 10 seconds to fill
2GB of memory, for example. Memset can cut the time in half
and using DMA currently yields a similar result.
The BIST engine of DDR controller provides support for
initializing any memory region with a pattern. This
bypasses the DDRSS bridge, so the required inline ECC
data is not computed and populated in the memory. For
some values like zero, the computed ECC syndrome is also
zero and we can use these values to preload the memory
from the DDR controller, without the assistance of the
bridge.
The registers involved in the process are described in the
'DDR controller registers' topic in [1] AM62 and [2] J721E
reference manuals.
The patch replaces the 'for' loop memory fill function with
the BIST memory initialization procedure. This cuts the time
to preload the 2GB memory from 10 seconds down to 1 second.
The bist preload function uses the lpddr4 APIs in the k3-ddrss,
so this is compatible with devices with both 16-bit LPDDR4 and
32-bit LPDDR4 interfaces (e.g J721E).
[1] AM62x: https://www.ti.com/lit/pdf/spruiv7
[2] DRA829/TDA4VM: https://www.ti.com/lit/zip/spruil1
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
Add ss_cfg memory region which maps the DDRSS configuration region
for the memory controller node.
Signed-off-by: Santhosh Kumar K <s-k6@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Tested-by: Neha Malcom Francis <n-francis@ti.com>
First, the "Boot Loader Specification" link has moved to a new location,
so link to that directly. Second, that link does not document as much of
the extlinux.conf format as I recall the old version doing at least.
However, the Syslinux Project wiki is the current location of the documentation
linked to in doc/README.pxe and also has a reference for SYSLINUX. Link
to both of these.
Signed-off-by: Tom Rini <trini@konsulko.com>
UEFI specification 2.11 has been published.
There are no changes relevant for the U-Boot scope.
So let us update the supported specification version.
Change the comment for the constant to Sphinx style.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This is done so that the device path protocol interface of the network
device can be changed internally by u-boot when a new bootfile gets
downloaded.
Signed-off-by: Adriano Cordova <adriano.cordova@canonical.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The command name was "sbi" instead of "sb" in "doc/usage/cmd/sb.rst",
the file documenting the "sb" command. It is annoying, because the
index in the left panel on the
<https://docs.u-boot.org/en/latest/usage/cmd/sb.html> page shows no
"sb" command, which makes difficult to navigate to the "sb"
documentation.
Fixed the command name: "sbi" -> "sb".
Fixes: ec6d30649c (doc: sandbox: Add docs for the sb command, 2024-10-28)
Signed-off-by: Olivier L'Heureux <olivier.lheureux@mind.be>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fix provided by 997fc12ec9 is actually introducing
a buffer overrun, and the overrun is effective if the
memory after the reloc section is not zeroed.
Probably that's why this bug is not always noticeable.
The problem is that 8-bytes 'rel' pointer can be 4-bytes aligned
according to the PE Format, so the actual relocate function can
take values after the reloc section.
One example is the following dump from the reloc section:
bce26000: 3000 0000 000c 0000 0000 0000 0000 0000
bce26010: 7c00 9340 67e0 f900 1c00 0ea1 a400 0f20
This section has two relocations at offset bce26008 and bce2600a,
however the given size (rel_size) for this relocation is 16-bytes
and this is coming form the efi image Misc.VirtualSize, so in this
case the 'reloc' pointer ends at affset bce2600c and is taken as
valid and this is where the overflow is.
In our system we see this problem when we are starting the
Boot Guard efi image.
This patch is fixing the overrun while preserving the fix done
by 997fc12ec9.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@belden.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
When the TCG2 protocol installation fails, we are trying to remove
all the objects we created in tcg2_uninit().
However, there are cases when this function runs before the config
table was installed. So instead of printing an error unconditionally
check against EFI_NOT_FOUND and don't print anything if the table wasn't
installed to begin with.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The bootmenu command can display
* menu entries defined by environment variables
* menu entries defined by UEFI boot options
Not in all cases showing the UEFI boot options is desired.
Provide a new parameter '-e' to select the display of UEFI boot options.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Currently when booting dhcp_run() may be executed multiple times:
once in eth_bootdev_hunt() and once in the network booting bootmeth.
We need to call eth_bootdev_hunt() when setting up the EFI sub-system to
supply the simple network protocol. We don't need an IP address set up.
We can reduce the bootime by not executing dhcp_run() in
eth_bootdev_hunt().
Furthermore eth_bootdev_hunt() with autostart=yes leads on the legacy
network stack leads to downloading a file via TFTP and to booting the
downloaded file.
Instead of running dchp_run() just check that there is a network device
in eth_bootdev_hunt().
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The CI uses the following command to launch xilinx_versal_virt_defconfig:
qemu-system-aarch64 -M xlnx-versal-virt \
-display none -m 4G -serial mon:stdio \
-device loader,file=u-boot,cpu-num=0
'usb start' or invoking eth_bootdev_hunt leads to a crash when function
dwc3_core_init() tries to access a register at offset 0xc704 (DWC3_DCTL)
relative to the register start address 0xfe20c100.
Disable CONFIG_USB_DWC3 in the CI until the driver problem is fixed.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
We do not actually test the code.
Scanning for Amiga partitions of the sandbox is extremely slow,
especially on the partially implemented USB device.
For build testing the other sandbox defconfigs are good enough.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
test_extension.py assumes that no extension is known at test start.
This assumption is wrong because we do not come out of reboot.
A prior test may have already hunted for the extension bootdev.
Remove the invalid assert.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
We should not write messages in UEFI API functions. This may lead to
incorrect screen layout in UEFI application.
For single statements after if clause we don't need braces.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
On some RISC-V including QEMU $loadaddr is 0x80200000.
For bootelf to work choose a different LOAD_ADDR to which the demo ELF
binary is relocated.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
To build the API examples on RISC-V we need to
implement _start and syscall for RISC-V.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
ARM, MIPS, and RISCV can use the same implementation of
platform_sys_info(). PPC provides some extra information.
So keep it separate.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
When a successful neighbor advertisement is received, the ethernet
address should be saved for later use to avoid having to redo the
neighbor discovery process.
For example, with TFTP the address should get saved into
"net_server_ethaddr". This is being done correctly with ARP for IPv4,
but not for neighbor discovery with IPv6.
Signed-off-by: Sean Edmond <seanedmond@microsoft.com>
Reviewed-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
timeout_count is never reset once a tftpput transfer has started. If for
whatever reason timeouts occur frequently, but the server keeps replying
nonetheless, the transfer may be needlessly aborted.
Reset timer_count on reception of an ACK to avoid this situation.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Linux DTS compatible MDIO bitbanging driver.
Both clause 22 and clause 45 MDIO supported and validated.
Heavily based on the Linux drivers (more or less the same code base).
Signed-off-by: Markus Gothe <markus.gothe@genexis.eu>
This reverts commit 431be621c6.
Section 3.3 of Reduced Gigabit Media Independent Interface (RGMII)
Version 2.0 (4/1/2002) details that a PHYs using a ~2ns internal delay
are referred to as RGMII-ID. This internal delay is optional.
Page 147-148 of the Marvell Doc. No. MV-S107146-U0 Rev. F details
timings of the RX/TX delays. We see that with the TX/RX_CLK delay
enabled, our RX/TX_CTL signal is shifted w.r.t CLK to reflect the delay
added.
In 431be62 there is no timing difference between RGMII and RGMII-ID, and
so programmers wanting to explicitly set their PHY to RGMII will find
that delay added anyway. This could throw off timing if that internal
delay is undesired.
We should be handling all 4 possible RGMII cases of PHY_INTERFACE_MODE:
RGMII, RGMII_ID, RGMII_TXID, and RGMII_RXID. Reverting 431be62
implements this.
See also m88e1111_config_init_rgmii_delays in the equivalent driver in
Linux (drivers/net/phy/marvell.c), which does not set these delays in
RGMII mode.
68e6eca was tested out on an 88E1512 PHY in RGMII-ID mode. This
reversion has been tested by myself on an 88E1518 in RGMII-ID mode. This
patch affects boards using this driver in "rgmii" mode, as the internal
delay will no longer be enabled. Namely kikwood-nsa310s.
Signed-off-by: Rufus Segar <rhs@riseup.net>
We have a some boards that rarely starts networking abnormally, so there are
many timeouts during file transfer. In the same time there is a normal transfer
between timeouts. In this case we can continue transfer (instead of connection
aborting) by just clearing timeout counter on every successful block.
This patch does not affect the case when several timeouts happen one after
another. The transfer will be aborted. Thus the transfer will be
continued in the case of unstable link, but will be aborted in the case
of inaccessible server.
Feature downside: it may greatly slowdown (instead of abort) file transfer
in the case of unstable link.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
When converting a U-Boot trace records file to ftrace function graph
format for use by trace-cmd ('proftool -f funcgraph dump-ftrace'), the
time associated to each function is incorrectly saved in microseconds
instead of nanoseconds. Multuply the value by 1000 to fix the issue.
With this change, the trace-cmd output looks consistent. Here is an
example with udelay(25) added to mem_malloc_init() as a test case:
$ ./tools/proftool -m System.map -t /tmp/trace.bin -f funcgraph \
dump-ftrace -o /tmp/trace.dat
$ trace-cmd report /tmp/trace.dat >/tmp/trace.log
$ vi /tmp/trace.log
[...]
u-boot-1 [000] 6.719659: funcgraph_entry: | mem_malloc_init() {
u-boot-1 [000] 6.719659: funcgraph_entry: | udelay() {
u-boot-1 [000] 6.719660: funcgraph_entry: | schedule() {
u-boot-1 [000] 6.719660: funcgraph_entry: | cyclic_run() {
u-boot-1 [000] 6.719660: funcgraph_entry: 1.000 us | cyclic_get_list();
u-boot-1 [000] 6.719661: funcgraph_exit: 1.000 us | }
u-boot-1 [000] 6.719661: funcgraph_exit: 1.000 us | }
u-boot-1 [000] 6.719661: funcgraph_entry: | __udelay() {
u-boot-1 [000] 6.719662: funcgraph_entry: 0.000 us | usec_to_tick();
u-boot-1 [000] 6.719687: funcgraph_exit: + 26.000 us | }
u-boot-1 [000] 6.719687: funcgraph_exit: + 28.000 us | }
u-boot-1 [000] 6.719687: funcgraph_entry: # 37971.000 us | memset();
u-boot-1 [000] 6.757658: funcgraph_exit: # 37999.000 us | }
u-boot-1 [000] 6.757658: funcgraph_exit: # 38000.000 us | }
In the above dump, the udelay() call is reported as taking 26 us which
is consistent with the timestamps (6.719687 - 6.719659 = 0.000026).
Without this patch we would have "0.026 us" instead of "+ 26.000 us".
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Move to using OF_UPSTREAM config and thus using the devicetree
subtree and remove unused device tree files.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Currently the driver relies on bootph flag to probe it during PRE_RELOC
stage but with the upcoming cleanup of v6.13, we don't have the bootph
property in the parent nodes anymore and ti_sci driver being one of the
parent nodes required during SPL stage would end up hampering the probe
model [0].
Add DM_FLAG_PRE_RELOC to ti_sci driver for mitigating this issue.
[0]: https://source.denx.de/u-boot/custodians/u-boot-dm/-/issues/21
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
The Texas Instruments Foundational Security (TIFS) firmware must match
the security level configured on the SoC. To boot Security Enforced (SE)
variants of the AM62Px, add another tiboot3 build which packages the
Security Enforced (SE) firmware variant for AM62Px SoCs.
Signed-off-by: Bryan Brattlof <bb@ti.com>
OSPI Boot requires overrides specific to R5 and also
to use DMA in R5 SPL stage the DM_TIFS needs to be used.
Add the corresponding overrides for R5 SPL stage.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Prasanth Babu Mantena <p-mantena@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
