On Puma v2.1 with a KSZ9031, the Ethernet PHY often doesn't detect the
link in the 4-second default timeout.
After some boot-loop test for about a thousand boots, 70% were below
10s, 90% below 15s and 100% below 30s. Let's play it safe and make it
30s so that hopefully all links that should be detected are.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Commit 2ce40542e0 ("power: rk8xx: properly print all supported PMICs
name") fixed all PMICs name that were broken but broke the only one that
was not broken already: RK808. This one is a special case because the ID
registers are marked as reserved and always return 0, so the variant
cannot be derived the same way it is done for other PMICs from Rockchip.
Fixes: 2ce40542e0 ("power: rk8xx: properly print all supported PMICs name")
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
In commit 100f489f58 ("rockchip: rk3399: Fix loading FIT from SD-card
when booting from eMMC"), the spi1 bootph properties were mistakenly
removed meaning, so re-add them back to fix SPI-NOR flash not being
found in U-Boot pre-reloc as required for RK3399 Puma.
Fixes: 100f489f58 ("rockchip: rk3399: Fix loading FIT from SD-card when booting from eMMC")
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the IO domain on Ringneck. Based on the current HW design, this
should do nothing else than making sure vccio6 iodomain is controlled by
the GRF and not GPIO0B6.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Port the PX30 part of the Rockchip IO Domain driver from Linux.
This differs from linux version in that the io iodomain bit is enabled
in the write ops instead of in an init ops as in linux, this way we can
avoid keeping a full state of all supplies that have been configured.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There are some sub-nodes under the grf DT nodes, so add bind callback
function in syscon_px30 driver to scan them recursively.
Fixes: e9ccb2f526 ("rockchip: add px30 architecture core")
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Haikou Devkit exposes 4 buttons over GPIO so let's enable their
support so their status can be queried from the `button` command from
the CLI.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This enables FIT verification in SPL for its payload (bl31, u-boot.itb,
...). This makes PX30 Ringneck match what happens on other Theobroma
boards.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
USB gadget simply doesn't work right now on PX30. Tested on PX30 EVB and
PX30 Ringneck with Linux mainline and Rockchip 5.10 Linux as well as
U-Boot.
We don't want to our users to assume that USB gadget is supported on Q7
USB P1 on Ringneck Haikou, so let's remove its support, which also
removes the ums CLI command, fastboot and Android image booting
support.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
We don't set many options in the board Kconfig entry file but instead
use defconfigs, select in some cases on the target itself, or update the
"default" options of the main entries when needed. In this case we can
remove most of the board Kconfig entries and just add them to the
defconfig like other platforms.
Signed-off-by: Tom Rini <trini@konsulko.com>
Marek Mojík <marek.mojik@nic.cz> says:
Hello all,
this is a continuation of previous work by Pali to add support for the
Turris 1.x board. As the patches were based on u-boot v2022.04, a
nontrivial rebasing was needed.
Some notes:
- Some options that are in SD defconfig are disabled in NOR defconfig
because over the years u-boot grew and the old NOR defconfig will not
fit into NOR memory.
- SD boot with RAM larger than 2GB will only allocate 2GB of RAM (We
were not able to fix this yet)
Add support for CZ.NIC Turris 1.x routers.
CZ.NIC Turris 1.0 (RTRS01) and 1.1 (RTRS02) are open source routers, they
have dual-core PowerPC Freescale P2020 CPU and are based on reference
Freescale P2020RDB-PC-A board design.
Hardware design is fully open source, all firmware and hardware design
files are available at Turris project website:
https://docs.turris.cz/hw/turris-1x/turris-1x/https://project.turris.cz/en/hardware.html
The P2020 BootROM can load U-Boot either from NOR flash or from SD card.
We add the new defconfigs, turris_1x_nor_defconfig, which configures
U-Boot for building the NOR image, and turris_1x_sdcard_defconfig, which
configures U-Boot for building an image suitable for SD card.
The defconfig for NOR image is stripped-down a - many config options
enabled in SD defconfig are disabled for NOR defconfig. This is because
U-Boot grew non-trivially in the last two years and it would not fit
into the space allocated for U-Boot in the NOR memory. In the future we
may try to use LTO to reduce the size of the code and enable more
options.
The design of CZ.NIC Turris 1.x routers is based on Freescale P2020RDB-PC-A
board, so some code from boards/freescale/p1_p2_rdb_pc is used and linked
into Turris 1.x board code.
Turris 1.x code in this patch uses modern distroboot and can boot Linux
kernel from various locations, including NAND, SD card, USB flash disks,
NVMe disks or SATA disks (connected to extra SATA/SCSI PCIe controllers).
Via distroboot is implemented also rescue NOR boot for factory recovery,
triggered by reset button, like on other existing Turris routers.
SD boot with RAM larger than 2GB will only allocate 2GB of RAM (We were
not able to fix this yet)
[ Because various CONFIG_ macros were migrated to Kconfig since the last
time this worked on upstream U-Boot (in 2022), a non-trivial rebasing
was needed and some issues were solved. ]
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
Use the CONFIG_IS_ENABLED() macro when checking for DM_SERIAL so that
CFG_SYS_NS16550_CLK is not defined as get_serial_clock() in SPL if SPL
does not have DM_SERIAL enabled.
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
Use CONFIG_VAL() for SYS_MONITOR_BASE in start.S so that correct value
is used for SPL.
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
The find_law() function searches for LAW just by physical address. This
is unsuitable for cases with overlapping LAWs. Extend it to
find_law_by_addr_id(), which searches for LAW by physical address and
target id.
Add a static inline definition of the original find_law() into fsl_law.h
header.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
This allows boards to fixup / overwrite DT model string when booting OS.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
When U-Boot is running from flash memory (execute in place) then
gd->fdt_blob before relocation points to read-only flash memory.
So U-Boot calls board_fix_fdt() with read-only gd->fdt_blob pointer which
cause immediate CPU crash when callback is trying to modify gd->fdt_blob.
Fix this issue by introducing a new config option OF_INITIAL_DTB_READONLY
which moves fix_fdt callback after the reloc_fdt callback. This makes
CONFIG_OF_BOARD_FIXUP working also if U-Boot before relocation is not
running from read/write (S)RAM memory.
This is required for mpc85xx boards when booting from flash NOR.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
This was added in commit 45a6d231b2 (bcm2835_wdt: support for the
BCM2835/2836 watchdog), which did do 'select HW_WATCHDOG'. That
incarnation of the watchdog driver later got removed in
c7adc0b5f9 (watchdog: bcm2835_wdt: Remove unused BCM283x watchdog
driver and its references), but this block was left behind.
Another rpi watchdog driver has since been added, but that does not
select HW_WATCHDOG, so this remains dead and unused. Remove it.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
This empty stub was originally added as one branch of an #ifdef in
commit 45a6d231b2 (bcm2835_wdt: support for the BCM2835/2836
watchdog). That incarnation of the rpi watchdog driver was later
removed in c7adc0b5f9 (watchdog: bcm2835_wdt: Remove unused BCM283x
watchdog driver and its references), but this now unused stub was left
behind. The later (re-)added rpi watchdog driver does not define a
hw_watchdog_disable() function, as that is properly integrated in the
watchdog framework.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
rev_scheme is an unsigned integer and must not be printed
as a signed integer.
Signed-off-by: Francois Berder <fberder@outlook.fr>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
This reverts commit 3304197272.
With the ability to generate this SMBIOS details autmotically the
small amount of details that this patch provided are generated
automatically so this is now obsolete so we can just drop it.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Matthias Brugger <mbrugger@suse.com>
u-boot-dfu-20240711
Usb gadget:
- A welcome cleanup: epautoconf workaround is dropped to use
.match_ep() instead
- Introduce handle_interrupts() op for USB_GADGET_GENERIC, which
allows a per-driver interrupt handling
Fastboot:
- Fix mssing include when building with TCP only
The build option to support images of type 'IMAGE_FORMAT_LEGACY' is
CONFIG_LEGACY_IMAGE_FORMAT so update the pytest to check for the correct
option.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The ARASAN MMC controller on Keystone 3 class of devices need the SDCD
line to be connected for proper functioning.
In cases where this can't be connected, add a quirk to force the
controller into test mode and set the TESTCD bit. Use the flag
"ti,fails-without-test-cd", to implement this above quirk when required.
Additionally, this quirk also avoids waiting for the controller debounce
time.
This commit is similar to linux kernel commit c7666240ec76
("drivers: mmc: sdhci_am654: Add the quirk to set TESTCD bit").
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Add and use the correct number of ddr phy registers to update the
corresponding settings.
Fixes: cbf5c99ef3 ("board: phytec: common: Introduce a method to inject DDR timings deltas")
Signed-off-by: Dominik Haller <d.haller@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
When building with the igep00x0_defconfig, the following warning is shown:
$ make -j $(nproc)
...
LD spl/u-boot-spl
OBJCOPY spl/u-boot-spl-nodtb.bin
SYM spl/u-boot-spl.sym
CAT spl/u-boot-spl-dtb.bin
COPY spl/u-boot-spl.bin
MKIMAGE MLO
===================== WARNING ======================
This board does not use CONFIG_DM_I2C (Driver Model
for I2C drivers). Please update the board to use
CONFIG_DM_I2C before the v2022.04 release. Failure to
update by the deadline may result in board removal.
See doc/develop/driver-model/migration.rst for more info.
====================================================
The only reason why I2C is enabled for the IGEP boards is that the TWL4030
driver requires it.
But both the TWL4034 and the OMAP I2C controller drivers were converted to
the driver model by commits daa69ffe3d ("drivers: i2c: omap24xx_i2c:
adopt omap_i2c driver to driver model") and fb1b7712ad power: make most
tps drivers and the twl4030 driver compatible with DM_I2C") respectively.
So there's no reason anymore to keep using the I2C legacy API and instead
the DM_I2C option could just be enabled.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Enric Balletbo i Serra <eballetbo@gmail.com>
In some FDTs, there is not enough free memory to add nodes, so this
operation fails.
Signed-off-by: Maxim Moskalets <maximmosk4@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This allows spliting partition list to several lines in environment file
ex:
--------------------
gpt_partition_list=
name=boot1,size=5MiB,start=0x100000;
name=boot2,size=5MiB;
name=rootfs1,size=70MiB;
name=rootfs2,size=70MiB;
name=overlay1,size=20MiB;
name=overlay2,size=20MiB;
name=art,size=4MiB;
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Tested-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Christian Marangi <ansuelsmth@gmail.com> says:
This is an initial series that have all the initial trivial
fixes required for usage of OF_UPSTREAM for the mediatek SoC
This also contains the pcie-gen3 driver and the required tphy
support driver to make it work.
Subsequent series will follow with conversion of the mtk-clk
to permit usage of OF_UPSTREAM and upstream clk ID.
MT7981, MT7986 and MT7988 migration to upstream clock ID
is complete and working on MT7623.
Series CI tested with PR: https://github.com/u-boot/u-boot/pull/590
Support alternative compatible for fixed-plls clocks used upstream with
the compatible mediatek,mt7986-apmixedsys.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Support alternative compatible for fixed-plls clocks used upstream with
the compatible mediatek,mt7988-apmixedsys.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Set pcie-phy optional for PCIe gen3. MT7988 doesn't require it and
making it mandatory prevent the driver to correctly probe.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Upstream kernel linux define pinctrl for uart0, hence this pin group
and pinctrl driver is needed before relocation. Add DM_FLAG_PRE_RELOC
flag to init and mute mtk_serial error on early serial init.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add support for gpio-controller property in root pinctrl node.
This is to follow upstream linux DTSI that doesn't define the
gpio-controller and cells in dedicated nodes.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Support alternative compatible for fixed-plls clocks used upstream with
the compatible mediatek,mt7981-apmixedsys.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add support for upstream linux clock and map U-Boot property to the one
use in upstream linux where supported.
Also add handling for the use_internal_cd that on upstream is hardcoded
enabled on mt7620.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Upstream linux serial driver use a different logic to setup serial regs.
They have 2 interval:
- < 115200 we use lowspeed regs and 16 * baud
- >= 115200 we use highspeed
We currently use force_highspeed property to force usage of highspeed
regs even with low baud rate.
Add special handling if the upstream compatible is used where we just
apply the same interval with anything >= 115200 in highspeed simulating
force_highspeed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Upstream linux also provide the additional optional bus clock.
Add support for it and also enable the baud and bus clock on probe.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add support for optional arb and pmic clock for i2c provided in upstream
linux DTSI.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Upstream kernel linux use a different compatible mediatek,spi-ipm.
Add support for this compatible and add handling for the additional
clock similar to how it's done by the upstream driver and handling for
all the property enabled by default.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add MediaTek GEN3 PCIe controller support for filogic silicon.
This is adapted from the Linux version of the driver.
Signed-off-by: John Crispin <john@phrozen.org>
[ fix minor problems, fix checkpatch errors ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add support for PHY type switch via the mediatek topmisc syscon.
This is needed on mt7981 to make the PCIe correctly work and display
LinkUp.
Follow the same implementation done on Linux kernel with the usage of
the mediatek,syscon-type property.
Example:
u3port0: usb-phy@11e10700 {
reg = <0x11e10700 0x900>;
clocks = <&topckgen CK_TOP_USB3_PHY_SEL>;
clock-names = "ref";
#phy-cells = <1>;
mediatek,syscon-type = <&topmisc 0x218 0>;
status = "okay";
};
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
There are operations in buildman that result in running the cross-tools
(such as performing size checks) and now that we have not modified PATH
to know where our tools are, these operations fail.
This reverts commit 6c0a3cf75f.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Add mvebu_espressobin_ultra-88f3720_defconfig (Benjamin)
- Update DTS for Thecus N2350 board (Tony)
- Add "old" Marvell DDR3 training for Armada 38x and Turris Omnia
(Marek)
- Misc turris_omnia changes (Marek)
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/21504
- Fixes for i.MX8M and i.MX93 clk-composite.
- Set CAN oscillator frequency based on model on verdin-imx8mm.
- Enable CAAM for phycore-imx8mp_defconfig.
- Miscellaneous improvements for Gateworks i.MX8M boards.
- Fix initramfs boot on msc_sm2s_imx8mp.
- Fixe EQoS on imx8mp-beacon-kit.
- Fix error message in fsl_esdhc_imx.
