Set the ops structure as static const. The structure is not accessible
from outside of this driver and is not going to be modified at runtime.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since commit 7917c2e356 ("spi: fsl_espi: fix din offset") MTD is
basically broken because any read transaction will get wrong data. While
the commit in question will fix simple transfers (where both
SPI_XFER_BEGIN and SPI_XFER_END is set), it will break the most common
case, where opcode and address is send first and then data comes as a
second transfer.
This basically reverts commit 7917c2e356 ("spi: fsl_espi: fix din
offset") and make the fix particular for this simple case. Instead of
providing two buffers for reading and writing, just malloc one which is
used for both. This will work because the data is first written on the
SPI bus and then it will be read (and overwite the written data) into
the same buffer.
Suggested-by: Tomas Alvarez Vanoli <tomas.alvarez-vanoli@hitachienergy.com>
Fixes: 7917c2e356 ("spi: fsl_espi: fix din offset")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The last users of this legacy i2c stack have been removed or converted
to a modern part of the stack instead. Remove this code and references
to it.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@nabladev.com>
Set the ops structure as static. The structure is not accessible
from outside of this driver.
Reviewed-by: Heiko Schocher <hs@nabladev.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The virtio_blk_do_single_req function returns ulong, which normally is
the processed size, but in an error case can be the actual error. Use
the special IS_ERR_VALUE macro to test for error.
Addresses-Coverity-ID: CID 645833 (DEADCODE) & CID 645834 (NO_EFFECT)
Signed-off-by: Christian Pötzsch <christian.poetzsch@kernkonzept.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The main use case for u-boot on Apple silicon based devices is to
provide an EFI based bootloader for operating systems. This uses a
generic u-boot image with DTBs passed from an earlier boot loader
(m1n1). Use the generic board name "mac" for this purpose.
Signed-off-by: Janne Grunau <j@jannau.net>
The Cadence SD6HC (SDHCI spec v4.20+) controller uses a soft PHY whose
DLL delay characteristics vary with PVT (Process, Voltage, Temperature)
and board-level trace routing.
A static delay value programmed via device tree for SD High Speed mode is
insufficient because the optimal sampling point varies per board, SD card,
and operating conditions. Runtime calibration is required.
While the SD Physical Layer Specification does not mandate tuning for
SD HS mode (only for UHS-I SDR50/SDR104), the Cadence SD6HC PHY
requires runtime calibration of its receive data delay line to find a
valid sampling window under constrained clock conditions.
The tuning is triggered from the set_ios_post callback because at that
moment hardware has committed the new bus width, clock frequency, and speed
mode to the controller registers. This ensuring the tuning sequence runs
at the correct SD HS operating conditions.
The tuning is gated by a device tree property "cdns,sd-hs-tuning" so
that only boards requiring runtime calibration opt in. When enabled,
the driver performs a 40-tap DLL sweep using CMD19 to find the largest
consecutive passing window, then programs the midpoint into
PHY_DLL_SLAVE_CTRL_REG.
To enable on a board, add to the MMC node in device tree:
&mmc {
cdns,sd-hs-tuning;
};
Signed-off-by: Tze Yee Ng <tze.yee.ng@altera.com>
The following compilation error occurs when environment variable
KBUILD_OUTPUT is not set :
drivers/reset/stm32/stm32-reset-mp21.c:8:10: fatal error: stm32-reset-core.h: No such file or directory
8 | #include <stm32-reset-core.h>
| ^~~~~~~~~~~~~~~~~~~~
As stm32-reset-core.h is located in same directory than stm32-reset-mp21.c,
we should use #include "stm32-reset-core.h".
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Raphaël Gallais-Pou <rgallaispou@gmail.com>
The dwc3_free_one_event_buffer() function incorrectly called free()
on event buffer structures allocated with devm_kzalloc(). This
caused heap corruption and a synchronous abort when exiting
fastboot mode via "fastboot continue".
Device-managed memory is automatically freed when the device is
removed, so manual deallocation causes the heap allocator to access
corrupted metadata.
Fixes: 884b10e86a ("usb: dwc3: core: fix memory leaks in event buffer cleanup")
Signed-off-by: Balaji Selvanathan <balaji.selvanathan@oss.qualcomm.com>
Reviewed-by: Marek Vasut <marek.vasut+usb@mailbox.org>
The symbol USB_EMUL is how sandbox has access to USB. It's
implementation however enforces a few other requirements. It must have
SCSI enabled, and in turn that means it must have BLK enabled. Finally,
we should not be using SANDBOX itself as a symbol to decide what to
build or not build here, as SANDBOX is selected for COMPILE_TEST builds
as well and so may not have enabled the sandbox specific USB support.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marek.vasut+usb@mailbox.org>
As exposed by "make randconfig", we have an issue with the dependencies
for RESET_RZG2L_USBPHY_CTRL. As this functionally depends on
REGULATOR_RZG2L_USBPHY, express this dependency directly in Kconfig as
well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The USB_RENESAS_USBHS functionality can only work with DM_USB_GADGET
enabled, so express this dependency in Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Commit 70101c3217 ("virtio: mmio: Return error codes on probe
failures") returns -ENODEV where it would return 0 before. That path is
apparently hit in qemu and breaks boot device discovery
(virtio_bootdev_hunt() expects only ENOENT). So return -ENOENT in
that path instead.
The remaining two error returns in the function are untouched as I
don't know where they play a role.
Signed-off-by: Ludwig Nussel <ludwig.nussel@siemens.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Kuan-Wei Chiu <visitorckw@gmail.com>
A fixed gigabit link on a non-gigabit controller is only rejected
during PHY init (even though there is no PHY to init), because, on
device-tree parsing, the controller is not probed, and it is still
unknown whether it is gigabit-capable.
This code was only tested on emulator with a full-duplex RGMII
interface, but is expected to work in GMII or half-duplex as well.
Signed-off-by: Christian DREHER <christian.dreher@nanoxplore.com>
Cadence Ethernet MAC has a feature named user_io, which provides
some input and some output signals for arbitrary purpose in the SoC.
From the driver code, I understand that, on Atmel SoC, it is used to
drive the PHY mode.
At least on Cadence IP7014 r1p12, this feature is optional, and I am
working on a SoC that does not instantiate it. The presence of this
feature is advertised in DCFG1, this patch merely disables the access
to the user_io register based on this information.
I did not apply this change to the non-gigabit capable versions of
the IP, as I do not have documentation for them, and a new non-gigabit
instance is unlikely to appear. I prefer avoiding regressions on old
systems.
Signed-off-by: Christian DREHER <christian.dreher@nanoxplore.com>
The MACB uses specific address registers (SA Top and Bottom) to
filter source or destination MAC addresses.
On the Gigabit Ethernet version, SA1B is @0x88.
On the non-GEM version, SA1B is @0x98.
Before this commit, the code was always writing 0x98. By chance,
on GEM, this is the address of SA3B, allowing the driver to work
anyway.
The motivation for this change is to be able to use the driver on
an instance of the GEM with less than 4 SA registers.
Signed-off-by: Christian DREHER <christian.dreher@nanoxplore.com>
It does not exist in my setup (an on-going arm64 SoC), and removing
it does not cause any missing declaration, but some code called when
CONFIG_CLK is missing calls get_macb_pclk_rate, which is only defined
in arch/arm/mach-at91/include/mach/clk.h
Signed-off-by: Christian DREHER <christian.dreher@nanoxplore.com>
Replace the proprietary airoha,pnswap-rx / airoha,pnswap-tx boolean
device tree properties with the standard rx-polarity and tx-polarity
properties defined in phy-common-props.yaml.
Backward compatibility is maintained by reading the legacy boolean
properties first and passing them as the default_pol argument to
phy_get_rx/tx_polarity(). If the standard properties are absent the
legacy values are used transparently, so existing device trees remain
functional without modification.
Link: https://git.kernel.org/linus/66d8a334b57e64e43810623b3d88f0ce9745270b
Signed-off-by: Lucien.Jheng <lucienzx159@gmail.com>
Add a new PHY_COMMON_PROPS library that provides helper functions for
PHY drivers to read standardized polarity properties from the device
tree node:
- phy_get_rx_polarity() / phy_get_tx_polarity()
- phy_get_manual_rx_polarity() / phy_get_manual_tx_polarity()
The dt-bindings/phy/phy.h header with PHY_POL_NORMAL, PHY_POL_INVERT,
and PHY_POL_AUTO constants is provided via dts/upstream/include, which
is already in the build include path.
Ported from Merge tag 'phy-for-7.0':
git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Link: https://git.kernel.org/linus/e7556b59ba65179612bce3fa56bb53d1b4fb20db
Signed-off-by: Lucien.Jheng <lucienzx159@gmail.com>
Upstream devicetrees use a newer DT binding using cpsw-switch
compatibles. The bindings are a bit different, so two functions are
introduced to capture the differences, cpsw_eth_of_to_plat_switch() and
cpsw_eth_of_to_plat_legacy().
Signed-off-by: Markus Schneider-Pargmann (TI) <msp@baylibre.com>
Use driver data to pass the correct gmii_sel function. This way new
compatibles don't need manual compatible matching as is done in
cpsw_phy_sel().
Signed-off-by: Markus Schneider-Pargmann (TI) <msp@baylibre.com>
Since Linux commit c360eb0c3ccb ("dt-bindings: net: ethernet-controller:
Add informative text about RGMII delays"), the interpretation of RGMII
delays has changed. Prior to the commit, the RGMII Variant among "rgmii",
"rgmii-id", "rgmii-rxid" and "rgmii-txid" clearly specified whether it is
the MAC or the PHY that "should" add the delay. However, post that commit,
the RGMII Variant only specifies whether or not there is a delay on the
PCB traces between the MAC and the PHY, leaving it open as to who adds the
delay.
Hence, instead of enforcing the existence of the device-tree properties
"ti,rx-internal-delay" and "ti,tx-internal-delay", default to a delay
of 2ns, while continuing to override this delay with the aforementioned
properties, if they exist in the device-tree.
This is in line with the Linux driver implementation updated by commit
6bf78849371d ("net: phy: dp83867: use 2ns delay if not specified in DTB").
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Anshul Dalal <anshuld@ti.com>
msm_sdc_clk_init() uses clock-frequency to get the clock rate for SDC
clocks. However, the DT files seem to use max-frequency for the same.
Since msm_sdc_clk_init() doesn't find clock-frequency in the DT, it sets
201500000 as the clock rate and this results in timeout errors on IPQ
platforms.
Additionally, clock-frequency is not DT bindings compliant. Hence, get
clock rate using DT bindings compliant max-frequency.
Signed-off-by: Varadarajan Narayanan <varadarajan.narayanan@oss.qualcomm.com>
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Use CONFIG_$(PHASE_)DM_REGULATOR_PFUZE100 as the build condition for
pfuze100 regulator driver.
Add Kconfig option for SPL_DM_REGULATOR_PFUZE100.
To avoid break current platforms, set the Kconfig default value same
as PMIC_PFUZE100.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Some BUCKs could work in single/dual phase mode, not in independent
mode. In single/dual phase mode, registers of both regulators,
must be identically set. So configure mode and value for both BUCKs.
CONF registers are not touched, leave them as default OTP settings.
PFUZE100/200 SW3A/B, could work in single/dual phase mode, so introduce
a new macro by adding a pointer to the SW3B descriptor.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Some PFUZE regulators can operate in either low or high output voltage mode,
with different minimum voltages and voltage step sizes selected by a hardware
control bit. However, the current PFUZE100 regulator driver assumes low output
voltage mode only, resulting in incorrect voltage calculation and programming
when high voltage mode is enabled.
Extend the regulator descriptor to describe high output voltage mode by adding
a mask to detect the mode and a dedicated voltage description (min_uV and
step size). Update voltage get/set handling to dynamically select the correct
voltage parameters based on the high voltage mode bit.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
regulator-min-microvolt in device tree is not always match the minimal
voltage in the pmic datasheet, direclty using the min value from device
tree as base may cause wrong voltage settings being written.
Directly use the min_uV from datasheet to avoid wrong settings.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Depending on the phase selection (single or multi), the FPWM bits
configured forces the regulator to operate in PWM mode. In case of
multi-phase selection, the FPWM_MP bits enforce the regulator to also
operate in multi-phase. This fixes correct multi-phase operation.
While at this, correct incorrect macro alignment as well.
Fixes: 065a452ae6 ("power: regulator: tps65941: add regulator support")
Link: https://www.ti.com/lit/ds/symlink/tps6594-q1.pdf
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Takuma Fujiwara <t-fujiwara1@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add support of Renesas R-Car Gen5 window watchdog timer. Timeout
configuration is derived from CONFIG_WATCHDOG_TIMEOUT_MSECS, which
is more accurate than the 1-second granularity 'timeout' passed to
.start callback.
Reviewed-by: Stefan Roese <stefan.roese@mailbox.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add R-Car Gen5 RSIP controller remoteproc driver capable of starting
the SCP, Cortex-R52 and Cortex-A720 cores in Renesas R-Car R8A78000
X5H SoC. The SCP core is started by releasing the core from reset,
the Cortex-R52 and Cortex-A720 are started using the SCP SCMI call.
The entry point for SCP core is fixed to its STCM, entry points for
Cortex-R52 and Cortex-A720 are set during rproc load.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Allow cpu families as mcf5441x (m68k) to use the fsl_esdhc_imx driver
since the hardware ip module is the same.
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
---
Changes in v2:
- moved before menuconfig changes
Apologies for the delay, but please pull those sunxi changes into
v2026.07. Nothing earth shattering, mostly minor improvements like
better SPL power LED support, and fixes to some H616 DRAM setup. Also
some more forward looking enhancement for the SPI code. I also pulled in
Richard's raw NAND flash improvements for the H6/H616 SoC, though this
lacks proper peer testing due to the lack of mainline support for any
board actually employing those chips.
No need to reset user data length registers in SPL.
In SPL, only the first user data length register is used, so we don't
need to reset all of them.
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
In Allwinner SoCs, user data can be added in OOB before each ECC data.
For older SoCs like A10, the user data size was the size of a register
(4 bytes) and was mandatory before each ECC step.
So, the A10 OOB Layout is:
[4Bytes USER_DATA_STEP0] [ECC_STEP0 bytes]
[4bytes USER_DATA_STEP1] [ECC_STEP1 bytes]
...
NB: the BBM is stored at the beginning of the USER_DATA_STEP0.
Now, for H6/H616 NAND flash controller, this user data can have a
different size for each step.
So, we are maximizing the user data length to use as many OOB bytes as
possible.
Fixes: 7d1de98011 ("mtd: rawnand: sunxi_spl: add support for H6/H616 nand controller")
Fixes: f163da5e6d ("mtd: rawnand: sunxi: add support for H6/H616 nand controller")
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
In sunxi_nand_chip_init there's quite a lot of kfree/return, it's easy
to forget a kfree(), so use a goto/kfree instead.
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
[Andre: rename goto label, keep return 0;]
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
In sunxi_nfc_hw_ecc_{read,write}_chunk(), the ECC step was force to 0,
the reason is not trivial to get when reading the code.
The explanation is that, from the NAND flash controller perspective, we
are indeed at step 0 for user data length and ECC errors.
Just add a const value with an explanation to clarify things.
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Reviewed-By: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
The user data length (4) used all over the code hard coded.
And sometimes, it's not that trivial to know that it's the user data
length and not something else.
Moreover, for the H6/H616 this value is no more fixed by hardware, but
could be modified.
Using a define here makes the code more readable.
Suggested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
