The pedantic mode is run-time contolled, so
appropriate registry take place everytime.
Maybe it's worth to use compile-time control only.
So, the registry could be optimized out by an #ifdef.
Signed-off-by: Eugene Uriev <eugeneuriev@gmail.com>
This changes are probable worth to be generalized in a
separate .h-file so, making it able to cover
libc-mallocs and others, without too much copy-paste.
But the malloc<=>mALLOc substitutions interfere
with an elegant way to do this.
Signed-off-by: Eugene Uriev <eugeneuriev@gmail.com>
These fast helpers sometimes breach mem-chunk boundaries.
Thus they trigger mcheck alarm. Standard ones are accurate though.
Signed-off-by: Eugene Uriev <eugeneuriev@gmail.com>
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/20128
- Allow accessing job-rings from non-TrustZone on colibri-imx7.
- Add support for reading XEA hardware revision.
- Convert imx8mq/8mm/8mn/8mp-evk to OF_UPSTREAM.
- Add TMP support on imx8m*-venice-gw72xx.
- Miscellaneous fixes and improvements.
The XEA board has following hard constraints regarding size of binaries:
- u-boot.sb < 48 KiB
- u-boot.img < 448 KiB
Added values are supposed to avoid exceeding size of binaries during
future u-boot development.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The XEA board now has several HW revisions for SoM boards.
This patch provides support for reading this revision ID values in early
u-boot proper as production devices boot via falcon boot with correct DTB
flashed at production (so there is no need to alter SPL).
Additionally, the maximal SPL size (~55KiB) constraint is not allowing
having even simplified FIT support in it.
As a result it was necessary to handle reading GPIOs values solely in
u-boot proper as one configuration (i.e. 'single binary' -
imx28_xea_sb_defconfig) is not using SPL framework.
Moreover, the 'board_som_rev' environment variable will be used to point
correct configuration from the Linux FIT file.
Additionally, as now XEA has its second HW revision - this information is
printed when u-boot proper starts.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The imx287 based XEA board's revision 2 uses GPIO_3_21 for PHY reset
It is safe to keep the GPIO_2_13 as well, as in the SPL SPI1 is not
used for transmission. This simplifies the code, as the proper
configuration is performed either in falcon boot's read DTB or in
u-boot proper (with correct FIT configuration chosen).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
With Ethernet DM in place, there is no longer the need for having
the board_phy_config() and setup_fec() functions anymore.
Remove them.
Successfully tested a TFTP transfer after these changes.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Change to regulator_set_enable_if_allowed to avoid enable failure,
in case same phy supply shared by multiple FEC controllers.
Signed-off-by: Ye Li <ye.li@nxp.com>
Set FSL_CAAM_JR_NTZ_ACCESS configuration since colibri-imx7
uses Freescale CAAM Job Ring linux driver
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Add a new kconfig option to allow non-secure world access
to the CAAM Job Ring.
This is needed, for example, when running linux without
OP-TEE services, as it's done on Colibri iMX7.
Fixes: 51f1357f34 ("Revert "drivers/crypto/fsl: assign job-rings to non-TrustZone"")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
On Colibri iMX8X, the gpio initialization and usage should be handled by
the device tree, not by the colibri-imx8x.c code. Therefore, remove it.
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Add a weak default reset_cpu() implementation just like
it is done on arch/arm/mach-imx/cpu.c.
This allows the removal of the empty reset_cpu() in several
board files.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Hiago De Franco <hiago.franco@toradex.com> # Toradex Colibri iMX8X
The GW71xx baseboard has a TPM that defined in the upstream dt however
we need to ensure the GPIO reset line is de-asserted which we do in boot
firmware with a gpio hog.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW7901 has GPIO's to configure the direction of its isolated
digital I/O signals. Add the GPIO pinmux, line names, and hog
configuration.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
CONFIG_USB_GADGET_VENDOR_NUM is a 16-bit number, so remove
the leading zero.
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Ilias Apalodimas <ilias.apalodimas@linaro.org> says:
The arm linker scripts had a mix of symbols and C defined variables in an
effort to emit relative references instead of absolute ones e.g [0]. A
linker bug prevented us from doing so [1] -- fixed since 2016.
This has led to confusion over the years, ending up with mixed section
definitions. Some sections are defined with overlays and different
definitions between v7 and v8 architectures.
For example __efi_runtime_rel_start/end is defined as a linker symbol for
armv8 and a C variable in armv7.
Linker scripts nowadays can emit relative references, as long as the symbol
definition is contained within the section definition. So let's switch most
of the C defined variables and clean up the arm sections.c file.
There's still a few symbols remaining -- __secure_start/end,
__secure_stack_start/end and __end which can be cleaned up
in a followup series.
For both QEMU v7/v8 bloat-o-meter shows now size difference
$~ ./scripts/bloat-o-meter u-boot u-boot.new
add/remove: 0/0 grow/shrink: 0/0 up/down: 0/0 (0)
Function old new delta
Total: Before=798861, After=798861, chg +0.00%
The symbols seem largely unchanged apart from a difference in .bss
as well as the emited sections and object types of the affected variables.
On the output below the first value is from -next and the second comes from
-next + this patchset. The .bss_start/end sections have disappeared from
the newer binaries.
# For example on QEMU v8:
efi_runtime_start
7945: 0000000000000178 0 OBJECT GLOBAL DEFAULT 2 __efi_runtime_start
7942: 0000000000000178 0 NOTYPE GLOBAL DEFAULT 2 __efi_runtime_start
efi_runtime_stop
9050: 0000000000000d38 0 OBJECT GLOBAL DEFAULT 2 __efi_runtime_stop
9047: 0000000000000d38 0 NOTYPE GLOBAL DEFAULT 2 __efi_runtime_stop
__efi_runtime_rel_start
7172: 00000000000dc2f0 0 OBJECT GLOBAL DEFAULT 10 __efi_runtime_rel_start
7169: 00000000000dc2f0 0 NOTYPE GLOBAL DEFAULT 10 __efi_runtime_rel_start
__efi_runtime_rel_stop
7954: 00000000000dc4a0 0 OBJECT GLOBAL DEFAULT 10 __efi_runtime_rel_stop
7951: 00000000000dc4a0 0 NOTYPE GLOBAL DEFAULT 10 __efi_runtime_rel_stop
__rel_dyn_start
7030: 00000000000dc4a0 0 OBJECT GLOBAL DEFAULT 11 __rel_dyn_start
7027: 00000000000dc4a0 0 NOTYPE GLOBAL DEFAULT 11 __rel_dyn_start
__rel_dyn_end
8959: 0000000000102b10 0 OBJECT GLOBAL DEFAULT 12 __rel_dyn_end
8956: 0000000000102b10 0 NOTYPE GLOBAL DEFAULT 11 __rel_dyn_end
image_copy_start
9051: 0000000000000000 0 OBJECT GLOBAL DEFAULT 1 __image_copy_start
9048: 0000000000000000 0 NOTYPE GLOBAL DEFAULT 1 __image_copy_start
image_copy_end
7467: 00000000000dc4a0 0 OBJECT GLOBAL DEFAULT 11 __image_copy_end
7464: 00000000000dc4a0 0 NOTYPE GLOBAL DEFAULT 11 __image_copy_end
bss_start
12: 0000000000102b10 0 SECTION LOCAL DEFAULT 12 .bss_start
8087: 0000000000000018 0 NOTYPE GLOBAL DEFAULT 1 _bss_start_ofs
8375: 0000000000102b10 0 OBJECT GLOBAL DEFAULT 12 __bss_start
8084: 0000000000000018 0 NOTYPE GLOBAL DEFAULT 1 _bss_start_ofs
8372: 0000000000102b10 0 NOTYPE GLOBAL DEFAULT 12 __bss_start
bss_end
14: 000000000010bc30 0 SECTION LOCAL DEFAULT 14 .bss_end
7683: 000000000010bc30 0 OBJECT GLOBAL DEFAULT 14 __bss_end
8479: 0000000000000020 0 NOTYPE GLOBAL DEFAULT 1 _bss_end_ofs
7680: 000000000010bbb0 0 NOTYPE GLOBAL DEFAULT 12 __bss_end
8476: 0000000000000020 0 NOTYPE GLOBAL DEFAULT 1 _bss_end_ofs
# For QEMU v7:
efi_runtime_start
10703: 000003bc 0 OBJECT GLOBAL DEFAULT 2 __efi_runtime_start
10699: 000003c0 0 NOTYPE GLOBAL DEFAULT 2 __efi_runtime_start
efi_runtime_stop
11796: 000012ec 0 OBJECT GLOBAL DEFAULT 2 __efi_runtime_stop
11792: 000012ec 0 NOTYPE GLOBAL DEFAULT 2 __efi_runtime_stop
__efi_runtime_rel_start
9937: 000c40dc 0 OBJECT GLOBAL DEFAULT 8 __efi_runtime_rel_start
9935: 000c40dc 0 NOTYPE GLOBAL DEFAULT 9 __efi_runtime_rel_start
__efi_runtime_rel_stop
10712: 000c41dc 0 OBJECT GLOBAL DEFAULT 10 __efi_runtime_rel_stop
10708: 000c41dc 0 NOTYPE GLOBAL DEFAULT 9 __efi_runtime_rel_stop
__rel_dyn_start
9791: 000c41dc 0 OBJECT GLOBAL DEFAULT 10 __rel_dyn_start
9789: 000c41dc 0 NOTYPE GLOBAL DEFAULT 10 __rel_dyn_start
__rel_dyn_end
11708: 000da5f4 0 OBJECT GLOBAL DEFAULT 10 __rel_dyn_end
11704: 000da5f4 0 NOTYPE GLOBAL DEFAULT 10 __rel_dyn_end
image_copy_start
448: 0000177c 0 NOTYPE LOCAL DEFAULT 3 _image_copy_start_ofs
11797: 00000000 0 OBJECT GLOBAL DEFAULT 1 __image_copy_start
445: 0000177c 0 NOTYPE LOCAL DEFAULT 3 _image_copy_start_ofs
11793: 00000000 0 NOTYPE GLOBAL DEFAULT 1 __image_copy_start
image_copy_end
450: 00001780 0 NOTYPE LOCAL DEFAULT 3 _image_copy_end_ofs
10225: 000c41dc 0 OBJECT GLOBAL DEFAULT 10 __image_copy_end
447: 00001780 0 NOTYPE LOCAL DEFAULT 3 _image_copy_end_ofs
10222: 000c41dc 0 NOTYPE GLOBAL DEFAULT 10 __image_copy_end
bss_start
11: 000c41dc 0 SECTION LOCAL DEFAULT 11 .bss_start
11124: 000c41dc 0 OBJECT GLOBAL DEFAULT 11 __bss_start
11120: 000c41dc 0 NOTYPE GLOBAL DEFAULT 11 __bss_start
bss_end
13: 000cbbf8 0 SECTION LOCAL DEFAULT 13 .bss_end
10442: 000cbbf8 0 OBJECT GLOBAL DEFAULT 13 __bss_end
10439: 000cbbf8 0 NOTYPE GLOBAL DEFAULT 11 __bss_end
It's worth noting that since the efi regions are affected by the change, booting
with EFI is preferable while testing. Booting the kernel only should be enough
since the efi stub and the kernel proper do request boottime and runtime
services respectively.
Something along the lines of
> virtio scan && load virtio 0 $kernel_addr_r Image && bootefi $kernel_addr_r
will work for QEMU aarch64.
Tested platforms:
- QEMU aarch64
- Xilinx kv260 kria starter kit & zynq
- QEMU armv7
- STM32MP157C-DK2
[0] commit 3ebd1cbc49 ("arm: make __bss_start and __bss_end__ compiler-generated")
[1] binutils commit 6b3b0ab89663 ("Make linker assigned symbol dynamic only for shared object")
Previous patches cleaning up linker symbols, also merged any explicit
. = ALIGN(x); into section definitions -- e.g
.bss ALIGN(x) : instead of
. = ALIGN(x);
. bss : {...}
However, if the output address is not specified then one will be chosen
for the section. This address will be adjusted to fit the alignment
requirement of the output section following the strictest alignment of
any input section contained within the output section. So let's get rid
of the redundant ALIGN directives when they are not needed.
While at add comments for the alignment of __bss_start/end since our
C runtime setup assembly assumes that __bss_start - __bss_end will be
a multiple of 4/8 for armv7 and armv8 respectively.
It's worth noting that the alignment is preserved on .rel.dyn for
mach-zynq which was explicitly aligning that section on an 8b
boundary instead of 4b one.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
image_copy_start/end are defined as c variables in order to force the compiler
emit relative references. However, defining those within a section definition
will do the same thing since [0].
So let's remove the special sections from the linker scripts, the
variable definitions from sections.c and define them as a symbols within
a section.
[0] binutils commit 6b3b0ab89663 ("Make linker assigned symbol dynamic only for shared object")
Suggested-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Sam Edwards <CFSworks@gmail.com> # Binary output identical
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
__efi_runtime_start/end are defined as c variables for arm7 only in
order to force the compiler emit relative references. However, defining
those within a section definition will do the same thing since [0].
On top of that the v8 linker scripts define it as a symbol.
So let's remove the special sections from the linker scripts, the
variable definitions from sections.c and define them as a symbols within
the correct section.
[0] binutils commit 6b3b0ab89663 ("Make linker assigned symbol dynamic only for shared object")
Suggested-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Sam Edwards <CFSworks@gmail.com> # Binary output identical
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
commit 47bd65ef05 ("arm: make __rel_dyn_{start, end} compiler-generated")
were moving the __rel_dyn_start/end on c generated variables that were
injected in their own sections. The reason was that we needed relative
relocations for position independent code and linker bugs back then
prevented us from doing so [0].
However, the linker documentation pages states that symbols that are
defined within a section definition will create a relocatable
type with the value being a fixed offset from the base of a section [1].
[0] binutils commit 6b3b0ab89663 ("Make linker assigned symbol dynamic only for shared object")
[1] https://sourceware.org/binutils/docs/ld/Expression-Section.html
Suggested-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Sam Edwards <CFSworks@gmail.com> # Binary output identical
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
__efi_runtime_rel_start/end are defined as c variables for arm7 only in
order to force the compiler emit relative references. However, defining
those within a section definition will do the same thing since [0].
On top of that the v8 linker scripts define it as a symbol.
So let's remove the special sections from the linker scripts, the
variable definitions from sections.c and define them as a symbols within
the correct section.
[0] binutils commit 6b3b0ab89663 ("Make linker assigned symbol dynamic only for shared object")
Suggested-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Sam Edwards <CFSworks@gmail.com>
Tested-by: Sam Edwards <CFSworks@gmail.com> # Binary output identical
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
commit 3ebd1cbc49 ("arm: make __bss_start and __bss_end__ compiler-generated")
and
commit f84a7b8f54 ("ARM: Fix __bss_start and __bss_end in linker scripts")
were moving the bss_start/end on c generated variables that were
injected in their own sections. The reason was that we needed relative
relocations for position independent code and linker bugs back then
prevented us from doing so [0].
However, the linker documentation pages states that symbols that are
defined within a section definition will create a relocatable type with
the value being a fixed offset from the base of a section [1].
So let's start cleaning this up starting with the bss_start and bss_end
variables. Convert them into symbols within the .bss section definition.
[0] binutils commit 6b3b0ab89663 ("Make linker assigned symbol dynamic only for shared object")
[1] https://sourceware.org/binutils/docs/ld/Expression-Section.html
Tested-by: Caleb Connolly <caleb.connolly@linaro.org> # Qualcomm sdm845
Tested-by: Sam Edwards <CFSworks@gmail.com> # Binary output identical
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
commit 3d74a0977f ("ti: am335x: Remove unused linker script") removed
the linker script for the TI variant. This linker script doesn't seem to
do anything special and on top of that, has no definitions for the EFI
runtime sections.
So let's get rid of it and use the generic linker script which defines
those correctly
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
- A few ncsi PHY fixes, clean up PHY GPIO reset code, support LEDs on
BCM54210E PHY, fix a signed shift overflow in the PHY code, hifemac
updates, E1000 i225-IT support, improve DM_MDIO+DM_PHY support and
enable it on the BeaglePlay platform.
Pull request acpi-next-20240328
ACPI:
* rename fields rename aslc_id, aslc_revision to match ACPI specification
* remove duplicate declaration of acpi_fill_header()
* document fields of HETP table
* MAINTAINERS: add include/acpi/ to ACPI
SMBIOS:
* provide wake-up type in SMBIOS table
* display wake-up type in smbios command
We should not use the reserved value 0x00 for the wake up type but
use 0x02 (Unknown).
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Correct type 1 output
* render wake up time as string
* print family string
* remove duplicate serial number output
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Document struct acpi_gen_regaddr and struct acpi_hpet.
Sphinx requires that the __packed attribute is at the end of the structure
definitions.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The fields Creator ID and Creator Revision contain information about the
tool that created an ACPI table. This may be the ASL compiler for some
tables but it is not for others. Naming these fields aslc_id and
aslc_revision is misleading.
It is usual to see diverse values of Creator ID. On a laptop I saw these:
'AMD ', 'INTL, 'MSFT', 'PTEC'. Obviously not all relate to the Intel
ASL compiler.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reset GPIO handling is done in ETH PHY Class driver.
Enable DM_ETH_PHY.
We don't use Fixed PHY so disable PHY_FIXED.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
If DM_ETH_PHY is enabled then try to bind and probe the
generic Ethernet PHY driver for each child of MDIO bus.
This is to ensure that GPIO reset handling is done if available
before MDIO bus driver scans for the PHYs.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Pull the PHY GPIO reset code into separate function, since
this is and will be reused multiple times. Set up default
reset assert and deassert timing to generous 20ms and 1ms
for maximum compatibility in case those DT properties are
missing.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
From the ethernet header is not on aligned, because the length
of the ethernet header is 14 bytes.
Therefore, unaligned access must be done here.
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
