i2c1 is having all chips on it that's why use it instead of 0.
You can see this error when you boot system.
eth0: ethernet@ff0c0000
Setting bus to 0
Failure changing bus number (-19)
Enable permission for node ID 33
Enable permission for node ID 47
Hit any key to stop autoboot: 0
It also get USB to work.
Fixes: dd4a822016 ("arm64: zynqmp: Introduce kria SOM defconfig")
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/cf07682a611de9895271d629ee00fb2809d99d0e.1702904913.git.michal.simek@amd.com
- Removed fdt_addr from verdin-imx8mm to fix booting via bootefi.
- Support Ethernet PHY autodection on Data Modul i.MX8M Mini/Plus eDM
SBC
- Add i.MX93 binman support
- Add support for imx93-var-som
Add support for the Variscite VAR-SOM-IMX93 evaluation kit. The SoM
consists of an NXP iMX93 dual A55 CPU. The SoM is mounted on a Variscite
Symphony SBC.
Signed-off-by: Mathieu Othacehe <m.othacehe@gmail.com>
Add dedicated Makefile targets for the i.MX93 and a new imx93-u-boot.dtsi
device-tree to create binman images.
Signed-off-by: Mathieu Othacehe <m.othacehe@gmail.com>
This is extending commit 6516c9b349 ("spl: binman: Disable u_boot_any
symbols for i.MX8M boards") to i.MX93 boards.
Signed-off-by: Mathieu Othacehe <m.othacehe@gmail.com>
fdt_addr variable is the location in flash of the device tree blob [1], it
does not exist for verdin-imx8mm.
Because of this the bootefi command fails unless the optional
`[fdt address]` parameter is passed on the command line,
bootefi.c:efi_install_fdt() assumes that `fdt_addr` is valid when
present.
Fix this removing fdt_addr from the U-Boot environment.
[1] doc/usage/environment.rst
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Implement fdtdec_board_setup() auto-detection of ethernet PHY.
This uses properties of the hardware and pull resistor placement.
If GPIO1_16 RGMII_MDC is HIGH, then R530 (MX8MM eDM SBC) or
R390 (MX8MP eDM SBC) is populated. R530 or R390 is populated
only on boards with AR8031 PHY.
If GPIO1_16 RGMII_MDC is LOW, then the in-SoM pull down is the
dominant pull resistor. This is the case on boards with BCM54213PE
PHY.
In case AR8031 PHY is populated, the PHY MDIO address is 0, in
case BCM54213PE PHY is populated, the PHY MDIO address is 1, the
fdtdec_board_setup() is used to patch the correct address into
the U-Boot control DT.
Enable broadcom PHY support to support both PHYs.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable the QEMU firmware interface if ACPI tables are to be supported on
the QEMU platform.
Enable the QFW MMIO interface if the QEMU firmware interface is enabled.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Invoke write_acpi_tables() via EVT_LAST_STAGE_INIT on QEMU except on X86.
X86 calls write_acpi_tables() in write_tables().
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We have two implementations of write_acpi_tables(). One for writing ACPI
tables based on ACPI_WRITER() entries another based on copying tables from
QEMU.
Create a symbol CONFIG_QFW_ACPI that signifies copying ACPI tables from
QEMU and use it consistently.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On non x86 platforms the hardware reduce flag must be set in the FADT
table. Write an error message if the flag is missing.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rebased on -next to use nomap, add hyphens:
Signed-off-by: Simon Glass <sjg@chromium.org>
If field X_FIRMWARE_CTRL is filled, field FIRMWARE must be ignored. If
field X_DSDT is filled, field DSDT must be ignored.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rebased on -next to use nomap:
Signed-off-by: Simon Glass <sjg@chromium.org>
Fields X_FIRMWAE_CTRL and X_DSDT must be 64bit wide. Convert pointers to
to uintptr_t to fill these.
If field X_FIRMWARE_CTRL is filled, field FIRMWARE must be ignored. If
field X_DSDT is filled, field DSDT must be ignored. We should not fill
unused fields.
See the field definitions in chapter "5.2.9 Fixed ACPI Description Table
(FADT)" of the ACPI Specification 6.5.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Standard passage provides for a bloblist to be passed from one firmware
phase to the next. That can be used to pass the devicetree along as well.
Add an option to support this.
Tests for this will be added as part of the Universal Payload work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
At present this code allocates memory when writing the tables and
then unnecessarily adds another memory map when installing it.
Adjust the code to allocate the tables using the normal U-Boot
mechanism. This avoids doing an EFI memory allocation early in
U-Boot, which may use memory that would be overwritten by a
'load' command, for example.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sandbox uses an API to map between addresses and pointers. This allows
it to have (emulated) memory at zero and avoid arch-specific addressing
details. It also allows memory-mapped peripherals to work.
As an example, on many machines sandbox maps address 100 to pointer
value 10000000.
However this is not correct for ACPI, if sandbox starts another program
(e.g EFI app) and passes it the tables. That app has no knowledge of
sandbox's address mapping. So to make this work we want to store
10000000 as the value in the table.
Add two new 'nomap' functions which clearly make this exeption to how
sandbox works.
This should allow EFI apps to access ACPI tables with sandbox, e.g. for
testing purposes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Use the word 'acpi' in this test so that it runs along with all the
other ACPI tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Only the v3 table is supported now, so always use this when installing
the EFI table.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
These tables are a pain since there is no way to handle memory above
4GB. Use SMBIOS3 always.
This should hopefully not create problems on x86 devices, since SMBIOS3
was released seven years ago (2015).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
All callers handle this alignment, so drop the unnecessary code. This
simplifies things a little.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
EFI does not use the 'anchor string' to determine the SMBIOS table
version, instead preferring to have two separate GUIDs. Use the correct
one, depending on the table version.
Call unmap_system() to balance to the use of map_sysmem()
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
When the SMBIOS table is written to an address above 4GB a 32-bit table
address is not large enough.
Use an SMBIOS3 table in that case.
Note that we cannot use efi_allocate_pages() since this function has
nothing to do with EFI. There is no equivalent function to allocate
memory below 4GB in U-Boot. One solution would be to create a separate
malloc() pool, or just always put the malloc() pool below 4GB.
- Use log_debug() for warning
- Rebase on Heinrich's smbios.h patch
- Set the checksum for SMBIOS3
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In preparation for adding support for SMBIOS3 move this code into an
else statement. There is no functional change.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Documentation updates for endeavoru, lg_x3, grouper and transformers,
addition of MIPI calibration clock name for T114 (inline with T124+),
conversion of TEGRA_SUPPORT_NON_SECURE into Kconfig and endeavoru
stability improvements.
This restores support for IOT2050 by widely synchronizing its DT files
with the Linux kernel. We additionally need to add the alias restoration
that is still waiting for its upstream merge and the not-yet-upstreamed
bits needed for watchdog reboot detection.
Fixes: 4dbdc84754 ("arm: dts: k3-am654: pull in dtb update from Linux")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
