Add UFS driver for UFS controller present on Renesas R-Car X5H R8A78000.
The controller uses different initialization code compared to previous
generation UFS controller present in Renesas R-Car S4 R8A779F0, and the
majority of the driver is the initialization, hence a new driver.
[Marek: Clean driver up, add SCMI reset handling, use read_poll_timeout(),
pass error values out of ufs_renesas_pre_init(), change the
compatible string to "renesas,r8a78000-ufs" to align with
previous generation "renesas,r8a779f0-ufs"]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Tuyen Dang <tuyen.dang.xa@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20251028142335.18125-7-marek.vasut+renesas@mailbox.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
A UFS device needs its bRefClkFreq attribute set to the correct value
before switching to high speed. If bRefClkFreq is set to the wrong
value, all transactions after the power mode change will fail.
The bRefClkFreq depends on the host controller and the device.
Query the device's current bRefClkFreq and compare with the ref_clk
specified in the device-tree. If the two differ, set the bRefClkFreq
to the device-tree's ref_clk frequency.
Taken from Linux kernel v6.17 (drivers/ufs/core/ufshcd.c and
include/ufs/ufs.h) and ported to U-Boot.
Signed-off-by: Jared McArthur <j-mcarthur@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Link: https://patch.msgid.link/20251010195556.1772611-3-j-mcarthur@ti.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Commit d232d7fdbf ("ufs: core: sync ufshci.h with Linux v6.12") updated
the Data Direction values from bitmask values to simple enumerations.
Before:
enum {
UTP_NO_DATA_TRANSFER = 0x00000000,
UTP_HOST_TO_DEVICE = 0x02000000,
UTP_DEVICE_TO_HOST = 0x04000000,
};
Updated:
enum utp_data_direction {
UTP_NO_DATA_TRANSFER = 0,
UTP_HOST_TO_DEVICE = 1,
UTP_DEVICE_TO_HOST = 2,
};
However, the U-Boot code still uses these values directly without shifting,
and resulting in wrong bitfield placement in the Transfer Request
Descriptor.
This fixes the issue by applying the necessary shift to align the value.
Fixes: d232d7fdbf ("ufs: core: sync ufshci.h with Linux v6.12")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20251010024557.673787-1-hayashi.kunihiko@socionext.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
In ti_j721e_ufs_probe there is a call to clk_get_rate but the code after
that attempts to detect an error from that call incorrectly uses
IS_ERR_VALUE. Instead the test should just be for regular error codes.
The call returns an unsigned long so that needs to be cast to a signed type
first of all.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Anshul Dalal <anshuld@ti.com>
Link: https://patch.msgid.link/20251007-ufs_ti-v2-1-501f575b6947@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Configure RMMI and M-PHY registers for HS mode required for selection of
bit rate series A or B. If it is not a calibrated part, then switch back
to SLOWAUTO_MODE and skip all these configurations.
Implemented below sequence as per the DWC RMMI databook.
1. Override RMMI CBRATESEL with the desired rate.
2. Set TX_CFGUPDT_0 to 1'b1 for one TX_CFGCLK_0 cycle.
3. Override PHY rx_req to 1, then poll on PHY rx_ack register till it
goes 1(both lanes).
4. Override PHY rx_req to 0, then poll on PHY rx_ack register till it
goes 0(both lanes).
5. Remove PHY rx_req override(both lanes).
6. Start the LS PMC.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250724044402.260149-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The link_startup_again logic was added in Linux to handle device
that were set in LinkDown state, which should not be the case since U-boot
doesn't set LinkDown state are init, and Linux sets the device active
in ufshcd_init() for the first link startup.
ufshcd_set_ufs_dev_active(hba) is called at ufshcd_init() right before
scheduling an ufshcd_async_scan that will call ufshcd_device_init() then ufshcd_link_startup().
The comment in probe says:
/*
* We are assuming that device wasn't put in sleep/power-down
* state exclusively during the boot stage before kernel.
* This assumption helps avoid doing link startup twice during
* ufshcd_probe_hba().
*/
we can assume the same from U-Boot.
While it worked to far, it breaks link startup for Qualcomm Controllers v5,
let's just remove the logic.
Tested-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Tested-by: Julius Lehmann <lehmanju@devpi.de>
Link: https://lore.kernel.org/r/20240930-topic-ufs-enhancements-v3-12-58234f84ab89@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
There is no need to flush and invalidate all data updated by the
driver, mainly because on ARM platforms flush also invalidates
the cachelines.
Split the function in two and add the appropriate cacheline
invalidates after the UFS DMA operation finishes to make sure
we read from memory.
Flushing then invalidating cacheline unaligned data causes data
corruption issues on Qualcomm platforms, and is largely unnecessary
anyway, so let's cleanup the cache operations.
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Tested-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Tested-by: Julius Lehmann <lehmanju@devpi.de>
Link: https://lore.kernel.org/r/20240930-topic-ufs-enhancements-v3-3-58234f84ab89@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d, reversing
changes made to 2ee6f3a5f7.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Extend the version check to handle UFS 3.1 controllers as well.
Tested on QEMU emulated UFS 3.1 controller.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a simple PCI based UFS controller driver with a QEMU
emulated UFS controller on the PCI bus.
Requiring QEMU v8.2+.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Check if the UFS controller is on the PCI bus, and get its register
base address accordingly.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Add a line feed to improve readability of some dev_xxx() messages.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
