The link_startup_again logic was added in Linux to handle device
that were set in LinkDown state, which should not be the case since U-boot
doesn't set LinkDown state are init, and Linux sets the device active
in ufshcd_init() for the first link startup.
ufshcd_set_ufs_dev_active(hba) is called at ufshcd_init() right before
scheduling an ufshcd_async_scan that will call ufshcd_device_init() then ufshcd_link_startup().
The comment in probe says:
/*
* We are assuming that device wasn't put in sleep/power-down
* state exclusively during the boot stage before kernel.
* This assumption helps avoid doing link startup twice during
* ufshcd_probe_hba().
*/
we can assume the same from U-Boot.
While it worked to far, it breaks link startup for Qualcomm Controllers v5,
let's just remove the logic.
Tested-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Tested-by: Julius Lehmann <lehmanju@devpi.de>
Link: https://lore.kernel.org/r/20240930-topic-ufs-enhancements-v3-12-58234f84ab89@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
There is no need to flush and invalidate all data updated by the
driver, mainly because on ARM platforms flush also invalidates
the cachelines.
Split the function in two and add the appropriate cacheline
invalidates after the UFS DMA operation finishes to make sure
we read from memory.
Flushing then invalidating cacheline unaligned data causes data
corruption issues on Qualcomm platforms, and is largely unnecessary
anyway, so let's cleanup the cache operations.
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Tested-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Tested-by: Julius Lehmann <lehmanju@devpi.de>
Link: https://lore.kernel.org/r/20240930-topic-ufs-enhancements-v3-3-58234f84ab89@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
This switches all boards with the Allwinner H616/H618/H313/H700 SoCs over to
use OF_UPSTREAM. We are doing it for this SoC family only since the DTs
between the U-Boot and the kernel repo are exactly identical, whereas other
families have one compatibility fix in U-Boot to allow booting older kernels.
Other will follow if this plays out well.
The biggest chunk otherwise is adding support for an Anbernic game console,
using the H700 SoC. For that we need to enhance the DRAM support code, and
pick two DT commits from the mainline kernel/DT rebasing repo, followed
by the defconfig patch.
On top of that two small fixes for the old Allwinner A80.
Gitlab CI passed, and I booted that briefly on some boards, including an
H616 and an H618 one (with LPDDR4).
Assorted Tegra enhancements. Merged with the recent XPL_BUILD changes,
resolve some whitespace issues and fix the name of the new apalis-tk1
env file by Tom.
Signed-off-by: Tom Rini <trini@konsulko.com>
This module is a color active matrix LCD module incorporating
Oxide TFT (Thin Film Transistor). It is composed of a color TFT-LCD
panel, driver ICs, a control circuit and power supply circuit, and
a backlight unit. Graphics and texts can be displayed on a 2560×1600
dots panel with (16,777,216) colors by using MIPI DUAL DSI interface,
supplying +3.3V DC supply voltage for TFT-LCD panel driving and
supplying DC supply voltage for LED Backlight.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Implement ganged mode support for the Tegra DSI driver. The DSI host
controller to gang up with is specified via a phandle in the device tree
and the resolved DSI host controller used for the programming of the
ganged-mode registers.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
It seems that DECLARE_GLOBAL_DATA_PTR use is not needed and video system
works perfectly fine without it.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Obtain USB phy configuration from phy node if such exists
and is enabled. If no, set default values.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Add previously undocumented SKU - AP20H found in LG Optimus 2X (P990).
Correct existing T20_7 name as it's proper name is AP20.
Signed-off-by: Ion Agorria <ion@agorria.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Change %02X to %02x since it always displayed 00 otherwise.
Signed-off-by: Ion Agorria <ion@agorria.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
In some cases access to GPIOs is needed so early that DM
is not ready even nearly. These functions are exactly for
this case.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Buildman has difficulties with constructing multi-dtb images, so
let's add a temporary custom recipe for it.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Tegra 3 has UART-E exposable via SD card slot which may be
handy for debugging. This change only adds funcmux part, to
use UART-E on the device you additionally would need:
- set stdout-path to serial@70006400 (uarte)
- configure sdmmc1_dat3_py4 and sdmmc1_dat2_py5 pinmux for
uarte
- disable or remove sdhci@7800000 node
- enable CONFIG_TEGRA_ENABLE_UARTE in defconfig
- set CFG_SYS_NS16550_COM to NV_PA_APB_UARTE_BASE in device
header
Signed-off-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Convert boards to use text based env. This is the first stage of
conversion, common inclusions should be converted next.
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com> # Toradex Apalis TK1
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
TegraPT is compatible with EFI part but it can't pass Protective MBR check.
Skip this check if CONFIG_TEGRA_PARTITION is enabled, storage uclass is MMC
and devnum is 0. Note, eMMC on supported devices MUST be aliased to mmc0.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Device tree for this board can be deleted. Device tree location
now points to the freescale/ directory.
Use absolute path to PMIC node entry and its regulators as
device tree in kernel does not provide corresponding labels
Signed-off-by: Gilles Talis <gilles.talis@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The SCU API alreay has been converted to return Linux error code,
using SCU error code is not correct here, although SC_ERR_NONE is value
as 0.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Simplify code and conform to the style guide used in the project by
making the following changes:
* Capitalize global constants
* Use single quotes for multiline strings (except docstrings)
* Fix line width to 79 cols
* Use f-string instead of formatting a regular string or using a
complicated concatenation
* Move common suffix used in keys to a global variable "KEY_NAME"
to reduce the likelihood of typos and making future changes
easier
Signed-off-by: Brian Ruley <brian.ruley@gehealthcare.com>
Cc: Marek Vasut <marex@denx.de>
