serial_out_dynamic() takes a u8* addr and uses it for 8-bit or 32-bit
accesses, depending on the value of plat->reg_width. This results in a
pointer type mismatch that the compiler may even turn into an error:
drivers/serial/ns16550.c: In function ‘serial_out_dynamic’:
drivers/serial/ns16550.c:115:42: error: passing argument 1 of ‘out_be32’ from incompatible pointer type [-Wincompatible-pointer-types]
115 | out_be32(addr, value);
| ^~~~
| |
| u8 * {aka unsigned char *}
This error was observed on PowerPC.
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
If there is an unallocated memory area before the last, filling parting
the size calculation for MTD_SIZE_REMAINING does not take this hole
into account.
Fix this by calculating the remaining size just based on total size
and partition offset.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Rename the variants of env_mmc_load() for redundant and non-redundant
environment to env_mmc_load_redundant() and env_mmc_load_singular()
respectively and convert the env_mmc_load() implementation to use of
if (IS_ENABLED(...)). As a result, drop __maybe_unused from
mmc_env_is_redundant_in_both_boot_hwparts().
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Introduce a new function mmc_env_is_redundant_in_both_boot_hwparts()
which replaces IS_ENABLED(ENV_MMC_HWPART_REDUND) and internally does
almost the same check as the macro which assigned ENV_MMC_HWPART_REDUND
did, and call it in place of IS_ENABLED(ENV_MMC_HWPART_REDUND).
The difference compared to IS_ENABLED(ENV_MMC_HWPART_REDUND) is
in the last conditional, which does not do plain macro compare
(CONFIG_ENV_OFFSET == CONFIG_ENV_OFFSET_REDUND), but instead does
mmc_offset(mmc, 0) == mmc_offset(mmc, 1). If OF_CONTROL is not
in use, this gets optimized back to original macro compare, but
if OF_CONTROL is in use, this also takes into account the DT
properties u-boot,mmc-env-offset and u-boot,mmc-env-offset-redundant.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Check wget_info->buffer_size for overflow and do not clean the wget_info struct
on failure, let the owner of the struct handle the error. The latter is necesary
, e.g., for when a request fails because the provided buffer was too small.
Signed-off-by: Adriano Cordova <adriano.cordova@canonical.com>
This commit fixes an use after free introduced in Commit e55a4acb54
(" efi_loader: net: set EFI bootdevice device path to HTTP when loaded
from wget"). The logic in efi_net_set_dp is reworked so that when the
function is invoked it not only changes the value of the static variable
net_dp (this is how the function was implemented in e55a4acb54) but also
updates the protocol interface of the device path protocol in case efi
has started.
Fixes: e55a4acb54 ("efi_loader: net: set EFI bootdevice device path to HTTP when loaded from wget")
Signed-off-by: Adriano Cordova <adriano.cordova@canonical.com>
This board does not have any NVMe slot, so disable unneeded
CONFIG_NVME_PCI option.
Fixes: bf4a33e725 ("board: rockchip: add FriendlyElec NanoPi R3S")
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The patch enables the second USB3.0 Type-A USB port on the NanoPi R4S
board, which prevents a crash when initializing the usb system in U-Boot
and allows both Type-A USB ports to be used for booting.
=> usb start
starting USB...
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3c0000: "Synchronous Abort" handler, esr 0x96000010, far 0x0
Signed-off-by: Justin Klaassen <justin@tidylabs.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
These two files were using IS_ENABLED() to test for CONFIG flags but omitted
the CONFIG_ prefix and so did not work as expected.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
BootROM leave GPIO4_D6 configured as SDMMC_PWREN function and DW MMC
driver set PWREN high in dwmci_init().
However, HW revision prior to v1.2 must pull GPIO4_D6 low to access
sdmmc. For HW revision v1.2 the state of GPIO4_D6 has no impact.
Upstream Linux commit 26c100232b09 "arm64: dts: rockchip: Fix sdmmc
access on rk3308-rock-s0 v1.1 boards" fixed this issue by adding a
vcc_sd regulator.
Include the new vcc_sd regulator in SPL and enable required Kconfig
options to set GPIO4_D6 low to fix reading sdmmc on v1.1 hw revision.
Fixes: 25438c40a0 ("board: rockchip: Add Radxa ROCK S0")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Refactor the entire kconfig page for mbedtls, adapt mbedtls makefile
and default config file using 'XPL_', in order to have independent
mbedtls kconfig options in U-Boot Proper, SPL, TPL and VPL.
User can choose legacy or mbedtls libraries for them independently.
Set mbedtls native hashing libraries as default when MBEDTLS_LIB,
SPL_MBEDTLS_LIB, TPL_MBEDTLS_LIB or VPL_MBEDTLS_LIB is selected.
If users prefer using U-Boot legacy hashing libraries, please select
MBEDTLS_LIB_HASHING_ALT, SPL_MBEDTLS_LIB_HASHING_ALT,
TPL_MBEDTLS_LIB_HASHING_ALT or VPL_MBEDTLS_LIB_HASHING_ALT for U-Boot
Proper, SPL, TPL and VPL respectively.
Moreover, rename a few kconfig options and update their descriptions to
improve the consistency of terminology.
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
U-Boot requires to access x509_internal.h, mbedtls_sha256_context and
mbedtls_sha1_context in the porting layer, and this requires to
enable MBEDTLS_ALLOW_PRIVATE_ACCESS.
Enable it to mscode and pkcs7_parser to fix a mbedtls internal building
error when X509 is selected.
Moreover, Move it to a separate file to avoid enabling it in multiple
places.
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Fixed the building failures when WGET_HTTPS,NET_LWIP and MBEDTLS_LIB
are selected due to a few incorrect kconfig dependencies.
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/24876
- Convert imx6q-lxr and imxrt1050 to OF_UPSTREAM.
- Fix potential memory leak on ]imx/imx8/imx8m]image.
- Restrict DDR_SI_TEST to only Siemens Capricorn board.
- Fix CONFIG_BOOTCOUNT_ALTBOOTCMD on Data Modul and DH imx8m boards.
There are some device-tree overlays with missing entries for the
keyfile. Add them to sign all images in the U-Boot FIT image.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
There are some device-tree overlays with missing entries for the
keyfile. Add them to sign all images in the U-Boot FIT image.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
The imx6q-lxr devicetree has landed in kernel 6.13.
Switch to OF_UPSTREAM to make use of the upstream devicetree.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Move content of dh_imx6_defconfig into dh_imx6.config. Retain legacy
dh_imx6_defconfig as multi-config for all DH i.MX6 DHSOM based boards.
Introduce separate imx6_dhcom_drc02_defconfig, imx6_dhcom_pdk2_defconfig
and imx6_dhcom_picoitx_defconfig for each i.MX6 DHSOM based board, to
make build for those boards easier. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Deduplicate the config files again, move CONFIG_BOOTCOUNT_ALTBOOTCMD
into common imx8mp_dhsom.config .
Fixes: 940135eea5 ("Kconfig: Move CONFIG_BOOTCOUNT_ALTBOOTCMD to Kconfig")
Signed-off-by: Marek Vasut <marex@denx.de>
Deduplicate the config files again, move CONFIG_BOOTCOUNT_ALTBOOTCMD
into common imx8m_data_modul.config .
Fixes: 940135eea5 ("Kconfig: Move CONFIG_BOOTCOUNT_ALTBOOTCMD to Kconfig")
Signed-off-by: Marek Vasut <marex@denx.de>
The environment is missing quotes for string variable, add them.
Fixes: 940135eea5 ("Kconfig: Move CONFIG_BOOTCOUNT_ALTBOOTCMD to Kconfig")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Dynamic memory, referenced by 'line', is allocated at imx8mimage.c:187
by calling function 'getline' and lost at imx8mimage.c:210.
Signed-off-by: Maks Mishin <maks.mishinFZ@gmail.com>
Dynamic memory, referenced by 'line', is allocated at imx8image.c:270
by calling function 'getline' and lost at imx8image.c:294.
Signed-off-by: Maks Mishin <maks.mishinFZ@gmail.com>
Dynamic memory, referenced by 'line', is allocated at imximage.c:761
by calling function 'getline' and lost at imximage.c:793.
Signed-off-by: Maks Mishin <maks.mishinFZ@gmail.com>
The DDR_SI_TEST config option is only relevant to the i.MX8 Capricorn
board.
Make DDR_SI_TEST depend on DDR_SI_TEST so that it does not show up
on other targets.
Signed-off-by: Liya Huang <1425075683@qq.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
The device tree for imxrt1050 is now
available in the /dts/upstream directory.
Migrate board to use OF_UPSTREAM.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Currently, booting via bootstd fails because the kernel cannot be retrieved.
The reason for this is the lack of 'kernel_addr_r'.
Pass 'kernel_addr_r' to fix booting via bootstd.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Currently, booting via bootstd fails because the kernel cannot be retrieved.
The reason for this is the lack of 'kernel_addr_r'.
Pass 'kernel_addr_r' to fix booting via bootstd.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The CONFIG_DEFAULT_FDT_FILE should be imx8mq_evk.dtb for this board
Fixes: 7050bd925f ("imx: imx8mq_evk: Switch to BOOTSTD")
Reported-by: Ludwig Nussel <ludwig.nussel@siemens.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Instead of doing another lookup, trivially access the struct mii_dev
embedded in struct bb_miiphy_bus . No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Instead of doing another lookup, trivially access the struct mii_dev
embedded in struct bb_miiphy_bus . No functional change.
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Instead of doing another lookup, trivially access the struct mii_dev
embedded in struct bb_miiphy_bus . No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
The struct bb_miiphy_bus embeds struct struct mii_dev, which
already contains one copy of name field. Drop the duplicate
top level copy of name field.
The a38x code does static assignment of disparate names, use
snprintf(...) to fill in matching name in probe to avoid any
breakage.
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Replace the name based look up in bb_miiphy_getbus() with trivial
container_of() call. This works because the struct bb_miiphy_bus
always embeds the matching struct mii_dev . This also makes the
code much simpler and more efficient.
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Allocate bb_miiphy using bb_miiphy_alloc() and fill in callbacks
currently listed in bb_miiphy_buses[] array. This is a temporary
duplication of assignment to avoid breakage, which will be removed
in follow up patches. At this point, the bb_miiphy callbacks can
reach these accessors by doing container_of() on struct mii_dev.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Allocate bb_miiphy using bb_miiphy_alloc() and fill in callbacks
currently listed in bb_miiphy_buses[] array. This is a temporary
duplication of assignment to avoid breakage, which will be removed
in follow up patches. At this point, the bb_miiphy callbacks can
reach these accessors by doing container_of() on struct mii_dev.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Allocate bb_miiphy using bb_miiphy_alloc() and fill in callbacks
currently listed in bb_miiphy_buses[] array. This is a temporary
duplication of assignment to avoid breakage, which will be removed
in follow up patches. At this point, the bb_miiphy callbacks can
reach these accessors by doing container_of() on struct mii_dev.
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Allocate bb_miiphy using bb_miiphy_alloc() and fill in callbacks
currently listed in bb_miiphy_buses[] array. This is a temporary
duplication of assignment to avoid breakage, which will be removed
in follow up patches. At this point, the bb_miiphy callbacks can
reach these accessors by doing container_of() on struct mii_dev.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Introduce bb_miiphy_alloc()/bb_miiphy_free() wrappers to allocate and free
struct bb_miiphy_bus. Make struct bb_miiphy_bus wrap struct mii_dev, which
will become useful later in bb_miiphy_bus accessors, which would be able
to access struct bb_miiphy_bus using container_of, even if the PHY stack
only passes in the inner struct mii_dev .
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Pull the bbmiiphy initialization code from designware_eth_probe() into
dedicated function, dw_bb_mdio_init(), just like all the other MDIO
initialization functions.
Keep check for "snps,bitbang-mii" in the designware_eth_probe(), so the
driver can initialize this MDIO only in case the property is present,
and initialize regular DW MDIO in case it is not present.
The dw_bb_mdio_init() allocates its own MDIO instance, because thus far
code gated behind "snps,bitbang-mii" did depend on allocation of MDIO bus
by the other two MDIO bus options and then rewrote the newly allocated
MDIO bus callbacks, which is wrong, instead allocate proper MDIO bus with
the correct callbacks outright.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
The .init callback is not called by any function, drop it.
There are no more users of the init callback, drop the entire
mechanism.
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
All the resources needed by this .init callback should already
be available by the time probe function runs, simply call the
init callback directly and set the bb_miiphy init callback to
NULL. This shouldn't break anything on this hardware, but would
be nice if someone could double-check and test that.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
