Inline FWRO, CARO, GWRO, TARO, RMRO macros directly into the
follow up register macros. FWRO, CARO, GWRO, TARO are already
zero, drop them. RMRO is 0x1000, increment all registers which
add RMRO by 0x1000 directly. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The forwarding engine CSD register offset changed between the
R-Car S4 and R-Car X5H. Parametrize this offset in preparation
for R-Car X5H addition into this driver. Clean up the macro
parameter names and make them more obvious. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The total port counts differ across variants of this IP in
R-Car S4 and R-Car X5H. Parametrize port count in preparation
for R-Car X5H addition into this driver. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The COMA, ETHA, GWCA offsets differ across variants of this IP in
R-Car S4 and R-Car X5H. Parametrize these offsets in preparation
for R-Car X5H addition into this driver. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This IP does support operating MII and SerDes via different ports.
Currently, the driver assumes that MII and SerDes are always bound
together on the same port, but this may not be the case. Implement
support for controlling MII and SerDes separately.
While the change is extensive, the gist of the change is to pass
pointer to the selected port registers to MII or SerDes functions,
depending on which port and operations should be done on that port.
Each combined ETHA instance contains both MII and SerDes register
pointers, which may not point to the same port, and passes those
registers to MII and SerDes functions respectively to control the
MII or SerDes of each port.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The new version of RSwitch3 in Renesas R-Car Gen5 uses multiple
clock to supply the IP. Convert the driver to bulk clock API to
cater for both single clock of R-Car S4 and multiple clock of
R-Car Gen5. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Empty RX DMA descriptor must contain .die_dt field set to DT_FEMPTY,
because hardware DMA overwrites this field to non-DT_FEMPTY when data
are received, and the .recv callback tests the content of RX descriptor
.die_dt field to determine whether hardware did receive any data and
updated the .die_dt field, and based on that information, receives a
packet or not. Fix the incorrect RX DMA descriptor initialization to
assure the .recv callback always works correctly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Fix indent from multiple spaces to tabs, to be consistent with
coding style and the rest of the driver. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Rockchip boards may depend on a working MMC regulator in SPL to
successfully load FIT payload from MMC. Typically, these boards only
include the vmmc-supply regulator and not its vin-supply in SPL control
FDT.
The commit f98d812e53 ("power: regulator: Add vin-supply for GPIO and
Fixed regulators") breaks loading FIT from MMC in SPL on some of these
boards due to now requiring the vin-supply to be included in the SPL
control FDT.
The commit also strangely enables any found vin-supply in
regulator_common_of_to_plat() and not when a regulator is enabled or as
part of regulator_autoset().
Revert the commit to fix FIT loading in SPL on broken boards.
If a board needs to have its vin-supply enabled, two options come to
mind:
- Add regulator-always-on prop to the regulator in the -u-boot.dtsi for
any board.
- Implement full support for reference counting of regulators and then
update the regulator-uclass to enable any found vin-supply when a
regulator is enabled.
This reverts commit f98d812e53.
Reported-by: Dang Huynh <danct12@riseup.net>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
If CONFIG_GPIO_HOG is not set, then gpio_hog_lookup_name() is empty,
and thus does not initialize any of its parameters. It does still
return 0 though, and so any calling function might assume that the
parameters have been initialized successfully.
Change the return value to -ENODEV in this case, as the function
would in the case when CONFIG_GPIO_HOG is set but the gpio hog
could not be found.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Heiko Schocher <hs@nabladev.com>
Introduce remote processor configuration for the i.MX93 Cortex-M33 core.
This patch adds:
- Address translation table (ATT) for i.MX93, including TCM
(secure and non-secure) and DDR regions.
- A new device configuration structure `imx_rproc_cfg_imx93` using SMC
method and ARM SMC ops.
- Device tree match entry for "fsl,imx93-cm33"
This enables remoteproc framework to properly initialize and manage the
Cortex-M33 core on i.MX93 platforms.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MQ/M use MMIO based method to directly configure SRC registers
to start/stop M4.
Add mmio ops to start/stop/is_running.
Add i.MX8MQ cfg data, i.MX8MN reuses i.MX8MQ data.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Support i.MX8MP/N with start/stop/device_to_virt/is_running/load
implemented. The device static configuration is mostly reused from
Linux Kernel with adapation to U-Boot dm_rproc_ops.
The booting method:
- load mmc 2:2 0x90000000 /lib/firmware/imx8mp_m7_DDR_rpmsg_lite_str_echo_
rtos.elf
- rproc load 0 0x90000000 ${filesize}
- rproc start 0
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Some areas needs to be initialized by using memcpy_toio and memset_io.
Following Linux Kernel commit: 40df0a91b2a5 ("remoteproc: add is_iomem to
da_to_va"), add this to U-Boot.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add support for the optional 'phy-supply' property in the ENETC MDIO
driver. This allows the driver to enable and manage the PHY's power
supply via the regulator framework when specified in device tree.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
This patch adds SPL Kconfig option (SPL_PHY_IMX8MQ_USB) for the i.MX8MQ,
i.MX8MP, i.MX95, and i.MX94 USB3.0 PHY driver, allowing the driver to be
compiled and probed in SPL stage.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Since the EHCI USB driver is shared across i.MX91, i.MX93, i.MX94, and
i.MX95, the condition check is updated to use IMX9.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Marek Vasut <marek.vasut@mailbox.org>
If OF_CONTROL is on, ti-musb.c registers a "ti-musb-wrapper" driver
that requires UCLASS_MISC. Hence, select MISC if both OF_CONTROL
and USB_MUSB_TI are selected.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
eMMC erase and write support on RK3528 is somewhat unreliable, sometime
e.g. mmc erase and write commands will fail with an error.
Use the delay line lock value for half card clock cycle, DLL_LOCK_VALUE,
to set a manual xx_TAP_VALUE to fix the unreliable eMMC support.
This is only enabled for RK3528, remaining SoCs still use the automatic
tap value, (DLL_LOCK_VALUE * 2) % 256, same value we configure manually
for RK3528.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add dummy implementation of set_rate for SCLK_GPU and SCLK_WIFI_PMU to
allow use of dts/upstream assigned-clocks in cru and pmucru nodes.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A variety of Qualcomm features/fixes for this cycle, notably with a few
new platforms gaining support:
* Initial support for SDM670 (similar to SDM845), SM6350, and SM7150
platforms is added
* USB and UART issues on MSM8916 are addressed (improving stability/
reliability)
* Firmware loading is implemented for the GENI serial engine, this is
used on some platforms to load firmware for i2c/spi/uart to work
Some additional patches like binman support for building MBN files still
need some additional work.
CI: 8ef6ac07b3/pipelines
Enable the serial engine clk in probe so that this driver can work on
platforms that don't already initialize the clk for this device before
this driver runs. This fixes a problem I see on Coreboot platforms like
Trogdor where the UART hardware isn't enabled by coreboot unless the
serial console build is used.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://patch.msgid.link/20250714-geni-load-fw-v5-6-5abbc0d29838@linaro.org
Signed-off-by: Casey Connolly <kcxt@postmarketos.org>
Qualcomm peripherals like UART, SPI, I2C, etc are all exposed under a
common GENI Serial Engine wrapper device. Replace the stub driver we use
for this currently with a full-on misc device and implement support for
loading peripheral firmware.
Each of the peripherals has it's own protocol-specific firmware, this is
stored on the internal storage of the device with a well-known partition
type GUID.
To support this, GENI will bind peripherals in two stages. First the
ones that already have firmware loaded (such as the serial port) are
bound in the typical way. But devices that require firmware loading are
deferred until EVT_LAST_STAGE_INIT. At this point we can be sure that
the storage device is available, so we load the firmware and then bind
and probe the remaining children.
Child devices are expected to determine if firmware loading is necessary
and call qcom_geni_load_firmware().
Since Linux currently doesn't support loading firmware (and firmware may
not be available), we probe all GENI peripherals to ensure that they
always load firmware if necessary.
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
Link: https://patch.msgid.link/20250714-geni-load-fw-v5-3-5abbc0d29838@linaro.org
Signed-off-by: Casey Connolly <kcxt@postmarketos.org>
NXP i.MX SoCs are available in different temperature grades. By default,
device-tree contains only thermal trips for consumer grade parts. On the
other hand, part temp grade fuse can be used to determine thermal trip
points. We already do this in imx_tmu_bind() function. Now, factor out
this functionality to a standalone function imx_tmu_set_trips() and use
it for both cases. This fixes an issue where 'cpu-thermal' child device
would set different thermal trips than the parent 'tmu@44482000' sensor,
depending on which gets used.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Guard execute_tuning with MMC_SUPPORTS_TUNING, otherwise there will be
build failure:
drivers/mmc/exynos_dw_mmc.c:484:10: error: 'struct dm_mmc_ops' has no member
named 'execute_tuning'
.execute_tuning = exynos_dwmmc_execute_tuning,
^~~~~~~~~~~~~~
Cc: Kaustabh Chakraborty <kauschluss@disroot.org>
Acked-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
