- Some cleanups in header files: those do not affect the generated
binaries at all.
- The usual update of DT files from the kernel repo, mostly adding new
board files this time. On the wake of this there is one defconfig to
enable a new board, some H618 TV box branded as "Transpeed".
- Samuel's series to support SPL FIT image loading for 32-bit SoCs as
well, so far this was restricted to ARM64 boards. I refrained from
automatically enabling this everywhere, instead this requires user
intervention during board configuration. This allows to ship the
"crust" management processor firmware on H3 boards, which enables
better power saving.
- One defconfig for an older H3 board. There was a close-by defconfig
for a related board, but there are some differences which deserve a
separate file.
- Support for the EMAC driver to work with fixed-link PHYs, which allows
to directly wire the MAC to a switch IC.
Add a following test cases for scsi commands:
scsi_reset - To reset SCSI controller
scsi_info - To show available SCSI devices
scsi_scan - To (re-)scan SCSI bus
scsi_device - To show or set surrent device
scsi_part - To print partition table of selected SCSI device
Signed-off-by: Love Kumar <love.kumar@amd.com>
Add the test cases for usb commands to test its various functionality
such as start, stop, reset, info, tree, storage, dev, part, ls, load,
and save. It also adds different file systems cases such as fat32, ext2
and ext4.
Signed-off-by: Love Kumar <love.kumar@amd.com>
Add the test cases for mmc commands to test its various functionality
such as mmc list, dev, info, rescan, part, ls, load, and save. It also
adds different file systems cases such as fat32, ext2 and ext4.
Signed-off-by: Love Kumar <love.kumar@amd.com>
Add test cases to verify the different type of secure boot images loaded
at DDR location for AMD's ZynqMP SoC. It also adds tests authentication
and decryption functionality using AES and RSA features for Zynq.
Signed-off-by: Love Kumar <love.kumar@amd.com>
Add gpio pins generic test for the set of gpio pin list to test various
gpio related functionality, such as the input, set, clear, and toggle,
it also tests the input and output functionality for shorted gpio pins.
This test depends on boardenv* configuration to define gpio pins names.
Signed-off-by: Love Kumar <love.kumar@amd.com>
Add testcases for loading RPU applications in split and lockstep mode
including the negative one for AMD's ZynqMP SoC.
Signed-off-by: Love Kumar <love.kumar@amd.com>
Update pygit2 and py to their latest versions. Even in the venv pygit2
still links against the system libgit2 library which is failing on
latest Arch Linux.
The py library also needs updating to fix a KeyNotFound exception during
test initialisation.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Now that 32-bit SoCs can load U-Boot proper (and possibly other firmware)
from a FIT, people can use that by enabling CONFIG_SPL_LOAD_FIT.
However SPL_FIT_IMAGE_TINY is required to stay within the 24 or 32 KiB
SPL size limit on early SoCs; for consistency, enable it everywhere.
Signed-off-by: Samuel Holland <samuel@sholland.org>
[Andre: drop unconditional FIT image enablement for all SoCs]
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Some 32-bit SoCs can use SCP firmware to implement additional PSCI
functionality, such as system suspend. In order to load this firmware
from SPL, we need to generate and use a FIT instead of a legacy image.
Adjust the binman FIT definition so it does not rely on TF-A BL31, as
this is not used on 32-bit SoCs. Instead, after loading the firmware,
U-Boot proper is executed directly. This requires to provide an
entry point property for the U-Boot image node, which confuses some
loaders like sunxi-fel, so protect that to only be used if we have no
BL31.
Signed-off-by: Samuel Holland <samuel@sholland.org>
[Andre: filter U-Boot entry point property]
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is easier to read than the #ifdef staircase, provides better
visibility into the memory map (alongside the other Kconfig
definitions), and allows these addresses to be reused from code.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Starting with H6, Allwinner removed the artificial 32 KiB SPL size limit
from the boot ROM. Now SPL size is only limited by the available SRAM.
This limit ranges from 152 KiB on H6 to a whopping 2052 KiB on R329. To
take advantage of this additional space, we must increase SPL_MAX_SIZE.
Since we do not want to unnecessarily pad SPL out to these giant sizes,
we must set SPL_PAD_TO to zero. This causes no problems because binman
already takes care of appending the SPL payload at the right offset.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
FriendlyElec NanoPi Duo2 is a tiny SBC with Allwinner H3 and
Ampak AP6212 WiFi module. The device-tree for it is already
available in u-boot source tree. Add a default config for it.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[Andre: enable USB gadgets]
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Make the "phy-handle" property optional, which allows support
for a fixed-link phy configuration.
Thus if the "phy-handle" is present in a DT, then driver will work as
before. Otherwise, phyaddr initialization will not be necessary,
as it is not needed in case of a fixed-link config.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
This is a Chinese TV box based on Allwinner H618 SoC.
The DRAM parameters were derived from the values found in a firmware update.
Signed-off-by: Nick Alilovic <nickalilovic@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Sync the devicetree files from the official Linux kernel tree, v6.8-rc1.
This time only small changes in the existing files, but five new boards
got added, which opens the door for their respective defconfig files.
As before, this omits the non-backwards compatible changes to the R_INTC
controller, to remain compatible with older kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
At the moment every Allwinner board builds and requires an SPL, even
though we select this individually in each _defconfig file.
For experiments and for early bringup of new SoCs it would be beneficial
to only build U-Boot proper, for instance to postpone a tedious SPL port
(including DRAM support) in the initial phase.
Protect some SPL related symbols that we unconditionally select at the
moment with "if SPL", to avoid Kconfig conflicts when CONFIG_SPL is
disabled.
This alone does not cleanly build U-Boot proper only yet, but gets it
far enough so that the binary can be harvested.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The usage of the common.h include file is deprecated, and has already
been removed from several files.
Get rid of all inclusions in the arch/arm/mach-sunxi directory. Most
files actually don't need the header at all, for the few others just
include the headers that we actually require.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The cpu_sun9i.h header file defined the base addresses for quite some
peripherals of the Allwinner A80 CPU, even though we now only use a
fraction of that.
Most of the addresses are now either read from the DT, or were never
used in U-Boot in the first place.
Removed the ones that are not used in the whole of the U-Boot source.
to make it clear that this file only contains addresses that are needed
for the SPL operation.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The cpu_sun4i.h header file defined the base addresses for quite some
peripherals of earlier Allwinner CPUs, even though we now only use a
fraction of that.
Most of the addresses are now either read from the DT, or were never
used in U-Boot in the first place.
Removed the ones that are not used in the whole of the U-Boot source.
to make it clear that this file only contains addresses that are needed
for the SPL operation.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The cpu_sun50i_h6.h header file defined the base addresses for quite some
peripherals of the Allwinner H6 and related CPUs, even though we now only
use a fraction of that.
Most of the addresses are now either read from the DT, or were never used
in U-Boot in the first place.
Removed the ones that are not used in the whole of the U-Boot source.
to make it clear that this file only contains addresses that are needed
for the SPL operation.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The sunxi-common.h configs header used to contain a lot of random
Allwinner platform related constants, but over the years we moved a lot
of those definitions out there.
Clean up the file to remove outdated comments which are leftovers from
the olden days. Also remove the definition of LOW_LEVEL_SRAM_STACK,
which is actually used nowhere in the whole source tree.
This also uses the opportunity to add some section comments that helps
structuring the header file and improving readability.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The header file is not necessary in either of those files,
remove it as common.h is going away.
Include missing asm/arch/rmobile.h in board/renesas/rcar-common/v3-common.c
to prevent build failure of r8a77970_eagle r8a779a0_falcon r8a77980_v3hsk
and r8a77970_v3msk .
Include missing asm/u-boot.h in falcon.c and grpeach.c to fix build failure
due to missing definition of struct bd_info . Include errno.h in grpeach.c
to fix build error due to missing definition of EINVAL.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Pull request smbios-2024-04-rc1-2
* Add missing field to SMBIOS type 2 structure definition
* Provide smbios command to display smbios table
* Enable the command on sandbox and qemu_arm64_defconfig
* Provide a python test for the smbios command
* Fix copying SMBIOS 2.1 table from QEMU
* Correct EFI TCG measurement to assume SMBIOS 3 table
As we support installing SMBIOS3 tables in U-Boot we need to add this GUID
to the translation table used buy uuid_guid_get_str().
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
The current code convert the SMBIOS 2.1 entry point structure to
SMBIOS 3.0 entry point structure. The max_struct_size member in
SMBIOS 2.1 entry point structure indicates
"Size of the largest SMBIOS structure, in bytes".
We need to use struct_table_length instead.
Fixes: 1c5aab803c ("smbios: copy QEMU tables")
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Current U-Boot only supports the SMBIOS 3.0 entry point structure.
TCG2 measurement code should migrate to SMBIOS 3.0 entry
point structure.
efi_selftest tcg2 test also needs to be updated, and expected
PCR[1] result is changed since guid for SMBIOS EFI system table
uses different guid SMBIOS3_TABLE_GUID instead of SMBIOS_TABLE_GUID.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
We have a Python test the copying of SMBIOS tables from QEMU.
To make use of the test we need the smbios command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Provide a unit test for the smbios command.
Provide different test functions for QEMU, sandbox, and other systems.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
U-Boot can either generated an SMBIOS table or copy it from a prior boot
stage, e.g. QEMU.
Provide a command to display the SMBIOS information.
Currently only type 1 and 2 are translated to human readable text.
Other types may be added later. Currently only a hexdump and the list of
strings is provided for these.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The type 2 structure must include information about the contained objects.
It is fine to set the number of contained object handles to 0.
Add the missing field.
Fixes: 721e992a8a ("x86: Add SMBIOS table support")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Additionally test a UTF-8 string where each code point translates to three
UTF-8 bytes.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
As we have had this file for a while now, we should include installing
and populating our pip cache from here as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
In case CONSOLE_MUX and SYS_CONSOLE_IS_IN_ENV are on and
stdin or stdout or stderr are missing in environment, as fallback, get
these either from stdio_devices[std] or stdio_devices[std]->name.
Fixes: 6b343ab38d ("console: Print out complete stdio device list")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
It seems that the U-Boot console entry of the bootmenu has lost
its original meaning. Now, even if it is chosen, the probability
that you will enter the actual U-Boot console is quite low.
Boot env, bootflow, bootcommand script may appear, but not the
actual console. Hence, let's remove ambiguity and name this
entry by what it actually does: 'Exit' the bootmenu.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Speed grade T requires the VDD_CORE voltage to be 0.85V if using
the maximum core frequency.
Speed grades G, K, S allow the VDD_CORE voltage to be 0.75V up to the
maximum core frequency but allow to run at 0.85V.
For efficiency in manufacturing and code maintenance we use 0.85V for
the PMIC defaults and device tree settings and dynamically adjust the
voltage in the PMIC and device tree to 0.75V for lower speed SKU to
gain more than 100mW power consumption reduction.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Add two functions, one which returns the SoC speed grade and one
which returns the SoC operating temperature range.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
mach-k3/am625_fdt.c does fdt fixup depending on fields in the device
identification register. Move the accessors to the device identification
register as inline functions into the am62_hardware.h header, so that
they can be used for other functionality.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
These headers follow the pattern:
| #if CONFIG_IS_ENABLED(FANCY_FEATURE)
| void foo(void);
| #else
| static inline void foo(void) { return -ENOSYS; }
| #endif
In the #else path ENOSYS is used, however linux/errno.h is not included.
If errno.h has not been included already the compiler errors out even
if the inline function is not referenced.
Make those headers self contained.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
