Add Renesas R-Car R8A78000 X5H MDLC power domain and reset driver,
which serves as a remap driver between DT power domain and reset IDs
and SCMI power domain and reset IDs in case U-Boot runs on Cortex-A,
and as a direct hardware access driver for RSIP.
The R-Car X5H SCP firmware uses different SCMI power domain and
reset IDs in different versions of the SCP firmware, which makes
this remapping necessary. The SCMI base protocol version is updated
for each new SCP firmware version, it is therefore possible to
determine which SCP firmware version is running on the platform
from the base protocol and then determine which remapping table to
use for DT power domain and reset ID to SCMI power domain and reset
ID remapping.
Currently supported versions are SCP 4.28, 4.31, 4.32 .
The DT power domain and reset ID to SCMI power domain and reset ID
remap and call mechanism is simple. Unlike SCMI clock protocol driver,
the SCMI reset and power domain protocol drivers register only a single
device. This driver looks up that single device, obtains its reset or
power domain ops, sets up struct reset_ctl or struct power_domain with
remapped SCMI ID, and invokes operations directly on the device.
In case of RSIP, all power domains are already enabled by BootROM or
early SoC initialization code, the driver therefore only acts as a
stub for the power domain part. The reset part operates as a direct
hardware access reset driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
pmic_reg_read returns a negative value if an error occurs. This
commit adds a missing check after calling pmic_reg_read.
Signed-off-by: Francois Berder <fberder@outlook.fr>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Set the ops structure as static const. The structure is not accessible
from outside of this driver and is not going to be modified at runtime.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Set the ops structure as static const. The structure is not accessible
from outside of this driver and is not going to be modified at runtime.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Set the ops structure as static const. The structure is not accessible
from outside of this driver and is not going to be modified at runtime.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Set the ops structure as static const. The structure is not accessible
from outside of this driver and is not going to be modified at runtime.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Set the ops structure as static const. The structure is not accessible
from outside of this driver and is not going to be modified at runtime.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Set the ops structure as static const. The structure is not accessible
from outside of this driver and is not going to be modified at runtime.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Set the ops structure as static const. The structure is not accessible
from outside of this driver and is not going to be modified at runtime.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Set the ops structure as static const. The structure is not accessible
from outside of this driver and is not going to be modified at runtime.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Set the ops structure as static const. The structure is not accessible
from outside of this driver and is not going to be modified at runtime.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Set the ops structure as static const. The structure is not accessible
from outside of this driver and is not going to be modified at runtime.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Set the ops structure as static const. The structure is not accessible
from outside of this driver and is not going to be modified at runtime.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Set the ops structure as static const. The structure is not accessible
from outside of this driver and is not going to be modified at runtime.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Set the ops structure as static const. The structure is not accessible
from outside of this driver and is not going to be modified at runtime.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Set the ops structure as static const. The structure is not accessible
from outside of this driver and is not going to be modified at runtime.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Set the ops structure as static const. The structure is not accessible
from outside of this driver and is not going to be modified at runtime.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Use CONFIG_$(PHASE_)DM_REGULATOR_PFUZE100 as the build condition for
pfuze100 regulator driver.
Add Kconfig option for SPL_DM_REGULATOR_PFUZE100.
To avoid break current platforms, set the Kconfig default value same
as PMIC_PFUZE100.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Some BUCKs could work in single/dual phase mode, not in independent
mode. In single/dual phase mode, registers of both regulators,
must be identically set. So configure mode and value for both BUCKs.
CONF registers are not touched, leave them as default OTP settings.
PFUZE100/200 SW3A/B, could work in single/dual phase mode, so introduce
a new macro by adding a pointer to the SW3B descriptor.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Some PFUZE regulators can operate in either low or high output voltage mode,
with different minimum voltages and voltage step sizes selected by a hardware
control bit. However, the current PFUZE100 regulator driver assumes low output
voltage mode only, resulting in incorrect voltage calculation and programming
when high voltage mode is enabled.
Extend the regulator descriptor to describe high output voltage mode by adding
a mask to detect the mode and a dedicated voltage description (min_uV and
step size). Update voltage get/set handling to dynamically select the correct
voltage parameters based on the high voltage mode bit.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
regulator-min-microvolt in device tree is not always match the minimal
voltage in the pmic datasheet, direclty using the min value from device
tree as base may cause wrong voltage settings being written.
Directly use the min_uV from datasheet to avoid wrong settings.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Depending on the phase selection (single or multi), the FPWM bits
configured forces the regulator to operate in PWM mode. In case of
multi-phase selection, the FPWM_MP bits enforce the regulator to also
operate in multi-phase. This fixes correct multi-phase operation.
While at this, correct incorrect macro alignment as well.
Fixes: 065a452ae6 ("power: regulator: tps65941: add regulator support")
Link: https://www.ti.com/lit/ds/symlink/tps6594-q1.pdf
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Takuma Fujiwara <t-fujiwara1@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Change the logic for selecting pmic_children_info to use the compatible
string from the devicetree instead of expecting the pwrap (part of the
MCU) to correspond to the separate PMIC chip.
In addition to being more correct, it also saves a few lines of code for
each MCU type that is added by dropping the enum and type field.
Reviewed-by: Julien Stephan <jstephan@baylibre.com>
Link: https://patch.msgid.link/20260409-mtk-pmic-fixes-v2-6-73e83aa6345b@baylibre.com
Signed-off-by: David Lechner <dlechner@baylibre.com>
Add a PWRAP_CAP_INIT capability flag to specify if it is safe to call
pwrap_init() or not. Not all targets define the registers accessed
by pwrap_init(). In that case, it is expected that an earlier bootloader
has already initialized the PMIC. If not, we now return an error instead
of trying to access undefined registers.
Reviewed-by: Julien Stephan <jstephan@baylibre.com>
Link: https://patch.msgid.link/20260409-mtk-pmic-fixes-v2-3-73e83aa6345b@baylibre.com
Signed-off-by: David Lechner <dlechner@baylibre.com>
As exposed by "make randconfig", we have an issue around how
SYSRESET_CMD_POWEROFF is typically selected. We cannot rely only on
CMD_POWEROFF as SYSRESET_CMD_POWEROFF must also be tested for its own
dependency of SYSRESET.
Signed-off-by: Tom Rini <trini@konsulko.com>
Fix a missing closing quote in the error message when a regulator name
is not unique.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Julien Stephan <jstephan@baylibre.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add a condition to enable the PMIC sysreset function via the
system-power-controller device tree property in addition to the existing
Kconfig dependency, provided the PMIC supports it.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de> # RK8xx
The Linux kernel CPCAP driver uses uppercase regulator node names, while
this driver uses lowercase. Since regulator names can be case-insensitive,
update the driver to support both uppercase and lowercase node names.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The bit_offset_from_cpcap_lowest_voltage value was inherited from the
downstream kernel as a quirk. With the correct voltage table, it is no
longer needed. An additional benefit is that SW1, SW2, and SW4 now share
the same voltage table.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Similar to pinctrl_select_state(), add dev_has_ofnode() check before doing the
real work. Device(scmi_base.0) does not have a real device node, ofnode_null()
is assigned as the device tree node for scmi base protocol device:
'commit 7eb4eb541c ("firmware: scmi: install base protocol to SCMI agent")'
However with recent update in
'commit 0535e46d55 ("scripts/dtc: Update to upstream version v1.7.2-35-g52f07dcca47c")',
SPL panic in fdt_check_node_offset_()->fdt_next_tag(), because offset is -1
and SPL_OF_LIBFDT_ASSUME_MASK is 0xFF.
So need to validate device tree node.
Reported-by: Ye Li <ye.li@nxp.com>
Closes: https://lore.kernel.org/u-boot/939a9696-27fa-45a1-b428-feffe21ac6d5@oss.nxp.com/
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Symbol CONFIG_SPL_DM_REGULATOR_FAN53555 is selected by
SPL_DM_PMIC_FAN53555 and used in a Makefile. But the
symbol definition is missing.
Add the missing configuration symbol.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add support for the PMIC wrapper (pwrap) IP block found on MediaTek
MT8365 and similar SoCs.
On these SoCs the PMIC is connected via SPI. The SPI controller is not
directly visible to the CPU, but only through the PMIC wrapper inside
the SoC.
Signed-off-by: Julien Masson <jmasson@baylibre.com>
Co-developed-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Co-developed-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add a new regulator driver for MT6359P and similar PMIC chips.
The MT6359P is a eco version for MT6359 regulator. For the MT8391
platform, we use the MT6359P (MT6365) as the main PMIC. The MT6359 and
MT6359P have different register maps. Therefore, on the MT8391 platform,
we only provide support for the MT6359P. If support for the MT6359 PMIC
it can be added later.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
