The hardware denies any access from the U-Boot non-secure world to the
secure-protected pins. Hence, prevent any driver to configure such a pin.
Identify the secure pins with "NO ACCESS" through the 'pinmux status -a'
command.
Use a driver data structure to identify which hardware versions support
this feature.
Signed-off-by: Fabien Dessenne <fabien.dessenne@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The cdns3_bind() function is responsible for identifying the appropriate
driver to bind to the USB Controller's device-tree node. If the device-tree
node has the 'dr_mode' property set to 'otg', the existing approach fails
to bind a driver, leading to loss of functionality.
To address this, use the VBUS Valid field of the OTG Status register to
determine the role as follows:
- If VBUS Valid field is set, it indicates that a USB Host is supplying
power and the Controller should assume the Peripheral role.
- If VBUS Valid field is clear, it indicates the absence of a USB Host and
the Controller should assume the Host role.
Additionally, when 'dr_mode' happens to be 'otg' and the STRAP settings
are not specified, use VBUS Valid to determine the role in cdns3_drd_init()
and assign it to cdns->dr_mode.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Marek Vasut <marek.vasut@mailbox.org>
u-boot-dfu-20260211
USB Gadget:
* dwc3: Support ip and version type
* dwc3: Increase controller halt timeout
* dwc3: Don't send unintended link state change
* dwc3: Improve reset sequence
* dwc2: Move dr_mode check to bind to support RK3288/RK3506 with
2 DWC2 controllers
Set RMII reference clock output to enabled (1) by default for VSC8541
PHY in RMII mode. The RMII specification requires a 50MHz reference
clock, and many board designs expect the PHY to provide this clock to
the MAC controller.
Previously, the driver defaulted rmii_clk_out to 0 (disabled) for all
interface modes, which caused the PHY to not output the required 50MHz
clock. This resulted in MAC-PHY communication failures and prevented
network operations like DHCP from working on RMII-configured boards.
This change alligns with the hardware power-up default behavior and
aligns with both the generic PHY driver and Linux MSCC PHY driver
implementations.
Signed-off-by: Pranav Tilak <pranav.vinaytilak@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20260129081054.1703479-1-pranav.vinaytilak@amd.com
When built without CONFIG_CMD_CLK, we get a warning about the unused
clk_names variable:
../drivers/clk/clk_zynqmp.c:153:27: warning: ‘clk_names’ defined but not used [-Wunused-const-variable=]
153 | static const char * const clk_names[clk_max] = {
So also guard it with CONFIG_CMD_CLK to get rid of that.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20260119095437.2775081-2-peter@korsgaard.com
Pull request net-20260209.
net:
- airoha: mdio support for the switch
- phy: mscc: allow RGMII with internal delay for the VSC8541
- dwc_eth_qos: Update tail pointer handling
net-legacy:
- Stop conflating return value with file size in net_loop()
net-lwip:
- wget: rework the '#' printing
- tftp: add support of tsize option to client
First set of u-boot-at91 features for the 2026.04 cycle:
This small fixes set includes fixing 64 bit builds and some warnings for
the at91 serial driver, and some cleanup on the nand driver.
i.MX95 uses System Manager(sm) API to start/stop logical machine or cpu.
There are two modes:
M7 in a dedicated logical machine, use LMM API
M7 and A55 in same logical machine, use CPU API
Extend the driver to using LMM and CPU protocol to manage the M7 core:
- Detect using LMM or CPU API in probe using API scmi_imx_lmm_info().
- Compare linux LM ID(got using scmi_imx_lmm_info) and M7 LM ID(the ID
is fixed as 1 in SM firmware if M7 is in a separate LM),
if Linux LM ID is not same as M7 LM ID(linux and M7 in same LM), use
LMM protocol to start/stop. Whether using CPU or LMM protocol to
start/stop, the M7 status detection could use CPU protocol to detect
started or not. So in imx_rproc_is_running, use scmi_imx_cpu_started to
check the status of M7.
- For above case (2), Use scmi_imx_lmm_power_boot to detect whether
the M7 LM is under control of A55 LM.
- For above case , after using SCMI_IMX_LMM_POWER_ON to check
permission, scmi_imx_lmm_shutdown API should be called to shutdown
the M7 LM.
- Add a new ops imx_rproc_ops_sm.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add a new flag ATT_ECC which indicates the memory region needs ECC
initialization. If the flag is set, clearing the whole memory region to
initialize ECC. If ECC is not initialized, remote core will crash if
directly access the area.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The i.MX91 SoC reuses the ENET FEC from i.MX93. Add all required driver
checks to make it work also on the i.MX91 based platforms.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Add the missing RGMII modes with internal delay for the VSC8541.
Fixes: a5fd13ad19 ("net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541")
Signed-off-by: Charles Perry <charles.perry@microchip.com>
mdio is a child node of the switch, so to get switch base address
we need to lookup for a parent node
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Commit d2145a89bc ("net: airoha: bind MDIO controller on Ethernet load")
uses "airoha,en7581-switch" dts node for finding MDIO childs. This is wrong
for EN7523 SoC. The correct node name should be used instead.
Fixes: d2145a89bc ("net: airoha: bind MDIO controller on Ethernet load")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Commit d2145a89bc ("net: airoha: bind MDIO controller on Ethernet load")
refers to non-present CONFIG_MDIO_MT7531 and non-present "mt7531-mdio"
driver. It should use CONFIG_MDIO_MT7531_MMIO and "mt7531-mdio-mmio"
instead.
Fixes: d2145a89bc ("net: airoha: bind MDIO controller on Ethernet load")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Multicast and Broadcast Queue Enable and Promiscuous Mode Enable bits
are currently written to "unused" registers using magic values.
Define more of the "unused" MAC regs based on information in the
DesignWare Cores Ethernet Quality-of-Service databook.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
The DesignWare Cores Ethernet Quality-of-Service databook state that
receive and transmit descriptor list address and also transmit and
receive tail pointer registers should be initialized before the receive
and transmit DMAs are started.
It also state to enable the MAC receiver only after the DMA is active.
Otherwise, received frames can fill the Rx FIFO and overflow.
Move the activation of receive and transmit DMA and MAC receiver until
after tail pointer registers have been initialized.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
The DesignWare Cores Ethernet Quality-of-Service databook state that
descriptors up to one location less than the one indicated by the
descriptor tail pointer are owned by the DMA. The DMA continues to
process the descriptors until the following condition occurs:
Current Descriptor Pointer == Descriptor Tail Pointer
The DMA goes into suspend mode when this condition occurs, and updating
the tail pointer resume the DMA processing.
Configure the transmit tail pointer to the first (current) descriptor
pointer so that the tail pointer is a valid address instead of being
initialized to NULL when transmit DMA is started.
Also update the receive tail pointer comment to state that by pointing
to the last descriptor we are actually implying that all receive
descriptors are owned by and can be processed by the DMA.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
The DesignWare Cores Ethernet Quality-of-Service databook state that the
descriptor address from the start to the end of the ring must not cross
the 4GB boundary.
Use lower_32_bits() to write the lower 32 bits of descriptor addresses,
including the 32-bit tail pointers, consistently. No functional change
is intended.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
The Kconfig menu "TrueType Fonts" should only be shown if TrueType is
enabled.
Put all TrueType dependent customization within one if statement.
Remove `depends TRUETYPE` clauses.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <simon.glass@canonical.com>
George McCollister <george.mccollister@konsulko.com> says:
This patch series brings over several changes from Linux that are required
to get PCIe working on the j722s and also enables PCIe in
j722s_evm_a53_defconfig. This allows Linux to be booted from an NVMe drive.
The J722S SoC provides pcie0 (using pcie_cdns_ti) thru serdes1
(using phy-cadence-torrent) thru serdes_wiz1 (using phy-j721e-wiz). Changes
to the three drivers needed to be ported from Linux to enable the REFCLK
output which is used with this SoC. These changes should be tested on other
platforms using these drivers by those with the hardware available to make
sure no problems were introduced.
The PCIe controller in this SoC relies on the code performing the PCI scan
not scanning devices which cannot exist. In Linux this is implemented as
only_one_child() in probe.c. If this mechanism is not used, PCI config reads
for subsequent functions will return information for device 0 resulting in
U-Boot detecting 32 devices when only 1 is present. This change should be
tested on other platforms with PCI to ensure the same PCI devices are
enumerated before and after the patch is applied.
I would like to thank Opto 22 for sponsoring the initial development and
anyone that is able to contribute to testing of patches.
Link: https://lore.kernel.org/r/20260130153856.2049575-1-george.mccollister@konsulko.com
cmn_refclk_<p/m> lines in Torrent SERDES are used for connecting an
external reference clock. cmn_refclk_<p/m> can also be configured to
output the reference clock. Model this derived reference clock as a
"clock" so that platforms like AM642 EVM can enable it.
This is used by PCIe to use the same refclk both in local SERDES
and remote device. Add support here to drive refclk out.
Based on: https://lore.kernel.org/all/20210310120840.16447-7-kishon@ti.com/
Signed-off-by: George McCollister <george.mccollister@konsulko.com>
Tested-by: Bryan Brattlof <bb@ti.com>
cmn_refclk_<p/m> lines in Torrent SERDES are used for an connecting
external reference clock. cmn_refclk_<p/m> can also be configured to
output the reference clock. In order to drive the refclk out from the
SERDES (Cadence Torrent), PHY_EN_REFCLK should be set in SERDES_RST of
WIZ. Model PHY_EN_REFCLK as a clock, so that platforms like AM642 EVM
can enable it.
Based on: https://lore.kernel.org/r/20210310120840.16447-6-kishon@ti.com
Signed-off-by: George McCollister <george.mccollister@konsulko.com>
Tested-by: Bryan Brattlof <bb@ti.com>
Use the same mechanism as the Linux kernel to skip unnecessary (and in
the case of the J722S, errant) scanning of direct children of root
ports, downstream ports or bridges.
Based on Linux PCI code in the following files as of b927546677c8:
drivers/pci/probe.c
drivers/pci/pci.h
include/linux/pci.h
Signed-off-by: George McCollister <george.mccollister@konsulko.com>
Tested-by: Bryan Brattlof <bb@ti.com>
mtdpart internally enumerate partitions starting from zero, but partition
driver API enumerate partitions starting from 1, so wrong partition will
be queried. This is wrong.
Unnecessary debug message also was removed.
Fixes: c29a6daec1 ("disk: support MTD partitions")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
According to commit 84a42ae366 ("dm: core: Rename device node to indicate it is private")
node_ should not be aaccess outside driver model.
Signed-off-by: Andy Yan <andyshrk@163.com>
Currently, atmel-usart does not respect CONFIG_DEBUG_UART_SKIP_INIT so
it will always configure the debug UART.
However, this is unwanted on platforms on which TF-A or some other firmware
has already configured the debug UART.
This will be used for Microchip LAN969x support, so simply return early if
CONFIG_DEBUG_UART_SKIP_INIT is set.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Microchip LAN969x will not include any arch specific clk.h nor hardware.h,
so in order to support it only include <asm/arch/clk.h> and
<asm/arch/hardware.h> when AT91 is selected.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Move the arch specific atmel_serial.h header from AT91 to the generic
include/dm/platform_data.
This will be used for support on Microchip LAN969x.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
The H6/H616 boot ROM doesn't expect a SPL scrambled the same way as
older SoCs.
It doesn't use a specific seeds table, it expects a maximized ECC
(BCH-80), a specific BBM (FF000301) and doesn't work if empty pages are
skipped (it needs its specific BBM, even in the padding).
So, add a --soc=h6 option to support H6/616 with:
- more ECC strengths
- specific BBM
- default_scrambler_seeds[] with all values
- no empty pages skip
In Kconfig, select BCH-80 by default for SUNXI_SPL_ECC_STRENGTH to make
BROM happy.
And in scripts/Makefile.xpl, use --soc=h6 option when building for a
SUN50I_GEN_H6 SoC.
Tested on Whatsminer H616 board, booting from NAND.
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Co-developed-by: James Hilliard <james.hilliard1@gmail.com>
Signed-off-by: James Hilliard <james.hilliard1@gmail.com>
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
The MACRO NFC_PAGE_SHIFT(x) already deals with removing 10 from
nand->page_shift, so it shouldn't be done twice.
Fixes: 4ccae81cda ("mtd: nand: Add the sunxi NAND controller driver")
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Fix a cast to pointer from integer warning on ARM64
On 64bits platform, the casts done in {read,write}l() give that kind of
warnings:
drivers/mtd/nand/raw/sunxi_nand_spl.c: In function ‘check_value_inner’:
./arch/arm/include/asm/io.h:110:43: warning: cast to pointer from \
integer of different size [-Wint-to-pointer-cast]
110 | #define __raw_readl(a) (*(volatile unsigned int *)(a))
| ^
[...]
drivers/mtd/nand/raw/sunxi_nand_spl.c:81:27: note: in expansion of \
macro ‘readl’
81 | int val = readl(offset) & expected_bits;
Introduce {read,write}l_nfc inline function to do the right cast and
push the base address (SUNXI_NFC_BASE) into those functions, making the
code more readable.
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Introduce H6/H616 NAND controller support for SPL
The H616 NAND controller has the same base as A10/A23, with some
differences:
- MDMA is based on chained buffers
- its ECC supports up to 80bit per 1024bytes
- some registers layouts are a bit different, mainly due do the stronger
ECC.
- it uses USER_DATA_LEN registers along USER_DATA registers.
- it needs a specific clock for ECC and MBUS.
For SPL, most of the work was setting the clocks, adding the new
capability structure for H616 and supporting the new USER_DATA_LEN
registers.
Tested on Whatsminer H616 board (with and without scrambling, ECC)
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Introduce H6/H616 NAND controller support for U-Boot
The H616 NAND controller has the same base as A10/A23, with some
differences:
- MDMA is based on chained buffers
- its ECC supports up to 80bit per 1024bytes
- some registers layouts are a bit different, mainly due do the stronger
ECC.
- it uses USER_DATA_LEN registers along USER_DATA registers.
- it needs a specific clock for ECC and MBUS.
Introduce the basic support, with ECC and scrambling, but without
DMA/MDMA.
Tested on Whatsminer H616 board (with and without scrambling, ECC)
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Add MBUS Master Clock Gating Register for H6 and H616
For H6/H616, the NAND controller needs the MBUS NAND clock along with
CLK_NAND0/1 and CLK_BUS_NAND.
The bit locations are from H6/H616 User Manuals.
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Use generic macros for ECC_MODE and RANDOM_SEED
As H6/H616 registers are different, use more generic macros than hard
coded values specific to A10-like SoC.
No functional changes.
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Increase max_oobsize to take into account bigger OOB on 2KiB pages
Some NAND chip (e.g. Kioxia TC58NVG1S3HTA00) have a 2KiB page size +
128 bytes OOB.
In order to detect them, the max_oobsize has to be increased from 64 to
128 bytes.
Tested on Kioxia TC58NVG1S3HTA00 NAND chip on Whatsminer H616 board.
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Use defines instead of hardcoded values for NFC_ECC_{ERR_MSK,PAT_FOUND}
SPL is using hard coded values for ECC error detection and empty chunk
detection.
The H6/H616 registers for that have changed, the pattern found is no
more in the NFC_REG_ECC_ST register.
So, don't presume anymore that pattern_found is in NFC_REG_ECC_ST, and
read the pattern_found register to get this information.
Apart from an additional register reading, no functional change.
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Introduce NDFC Spare Area Register offset in SoC capabilities
The H6/H616 spare area register is not at the same offset as the
A10/A23 one, so move its offset into sunxi_nfc_caps.
No functional change.
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
NFC_RANDOM_{EN,DIRECTION} registers offset moved in H616
Let's make it a SoC capability.
NFC_RANDOM_DIRECTION also moved, but it's unused, just remove it.
No functional change.
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Introduce per SoC capabilities in sunxi_nand_spl.c
Prepare for the H616 support that has quite a lot of differences in
registers offset and capabilities.
Start with the 512 bytes ECC capability.
No functional change.
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
