Remove get_led() and setup_led() which became obsolete since
led_boot_on() introduction. led_boot_on() is automatically called
from board_r.c
Regarding "u-boot,error-led" property can't be used anymore since commit
Since commit 516a13e8db32 ("led: update LED boot/activity to new property implementation")
Instead get the LED labeled "red:status".
See kernel series: https://patchwork.kernel.org/project/linux-arm-kernel/list/?series=1022570
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Commit c37a668481 ("stm32mp: fix compilation issue with DEBUG_UART")
split the debug UART initialization code into two files, but failed to
update other non-ST boards. This did not lead to noticeable breakage
until debug UART is enabled, which is not the default. Update the
Makefile accordingly to allow debug UART to work.
Fixes: c37a668481 ("stm32mp: fix compilation issue with DEBUG_UART")
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add DRAM settings for 1 GiB variant of DH STM32MP13xx DHCOR SoM
and support for SoM DRAM coding HW straps decoding and automatic
DRAM configuration selection. Enable CONFIG_BOARD_EARLY_INIT_F on
all STM32MP1 DHSOM, as it is required for the HW straps decoding.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Update DRAM chip type and density comment for 512 MiB DRAM settings for
DH STM32MP13xx DHCOR DHSBC to match the chip on the SoM. No functional
change.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
STM32MP13xx may have OPTEE-OS at 0xdd000000 even on systems with 1 GiB
of DRAM at 0xc0000000, which is not the end of DRAM anymore. This puts
the OPTEE-OS in the middle of DRAM. Currently, the code sets RAM top to
0xdd000000 and prevents the DRAM range past OPTEE at 0xe0000000..0xffffffff
from being set as cacheable and from being usable. The code also sets the
area over OPTEE as invalid region in MMU tables, which is not correct.
Adjust the code such, that it only ever sets RAM top just before OPTEE
in case the OPTEE is really at the end of DRAM, mainly to be backward
compatible. Furthermore, adjust the MMU table configuration such, that
the regions over the OPTEE are simply skipped and not reconfigured, and
the regions between end of OPTEE and RAM top are set as cacheable, if
any actually exist.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Remove setting of fdt_high to ~0, which disables device tree relocation,
from the default environment. Doing so prevents U-Boot from correcting
problems such as having an unaligned device tree and leads to various
failure modes in the OS.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove setting of fdt_high to ~0, which disables device tree relocation,
from the default environment. Doing so prevents U-Boot from correcting
problems such as having an unaligned device tree and leads to various
failure modes in the OS.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove setting of fdt_high to ~0, which disables device tree relocation,
from the default environment. Doing so prevents U-Boot from correcting
problems such as having an unaligned device tree and leads to various
failure modes in the OS.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove setting of fdt_high to ~0, which disables device tree relocation,
from the default environment. Doing so prevents U-Boot from correcting
problems such as having an unaligned device tree and leads to various
failure modes in the OS.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove setting of fdt_high to ~0, which disables device tree relocation,
from the default environment. Doing so prevents U-Boot from correcting
problems such as having an unaligned device tree and leads to various
failure modes in the OS.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove setting of fdt_high to ~0, which disables device tree relocation,
from the default environment. Doing so prevents U-Boot from correcting
problems such as having an unaligned device tree and leads to various
failure modes in the OS. However, this platform also has a large comment
block that explains that given previous stage loaders and other parts of
the memory map (that may not be in the device tree we see?), adjust this
to use bootm_size to restrict relocation to be below the CMA area and
update the comment to match.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove setting of fdt_high to ~0, which disables device tree relocation,
from the default environment. Doing so prevents U-Boot from correcting
problems such as having an unaligned device tree and leads to various
failure modes in the OS.
Reviewed-by: Heiko Schocher <hs@nabladev.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove setting of fdt_high to ~0, which disables device tree relocation,
from the default environment. Doing so prevents U-Boot from correcting
problems such as having an unaligned device tree and leads to various
failure modes in the OS.
Signed-off-by: Tom Rini <trini@konsulko.com>
When this platform was removed the config header file was missed. Remove
that now.
Fixes: ddfc004009 ("arm: Remove xpress board")
Signed-off-by: Tom Rini <trini@konsulko.com>
When these platforms were removed the common config header file was
missed. Remove that now.
Fixes: a0cacddcaf ("arm: Remove zc5202 and zc5601 boards")
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove setting of fdt_high to ~0, which disables device tree relocation,
from the default environment. Doing so prevents U-Boot from correcting
problems such as having an unaligned device tree and leads to various
failure modes in the OS.
Tested-by: Greg Malysa <malysagreg@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
With the changes in commit 8fbcc0e0e8 ("boot: Assure FDT is always at
8-byte aligned address") to call memalign(...) we now always call
memalign(...) rather than malloc(...) when allocating a buffer that may
contain a device tree. However, memalign(...) is not portable among all
of the host OSes we support. The C11 standard does require that
aligned_alloc(...) exist and it takes the same parameters as
memalign(...) does. Change this file to call aligned_alloc rather than
memalign, and for the non-USE_HOSTCC case define that function back to
memalign.
Fixes: 8fbcc0e0e8 ("boot: Assure FDT is always at 8-byte aligned address")
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
The current implementation of clk_set_parent() unconditionally enables
the new parent clock, even if the target clock was not previously enabled.
To avoid this implicit behavior, this patch adds a check for whether
the target clock has been enabled before parent enabling..
Fixes: ac30d90f33 ("clk: Ensure the parent clocks are enabled while reparenting")
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Heiko Schocher <hs@nabladev.com> says:
Add SM3 secure hash, as specified by OSCCA GM/T 0004-2012 SM3 and described
at https://datatracker.ietf.org/doc/html/draft-sca-cfrg-sm3-02
TPMv2 defines hash algo sm3_256, which is currently
not supported and prevented TPMv2 chip with newer
firmware to work with U-Boot. Seen this on a ST33TPHF2XI2C
u-boot=> tpm2 init
u-boot=> tpm2 autostart
tpm2_get_pcr_info: too many pcrs: 5
Error: -90
u-boot=>
Implement sm3 hash, so we can fix this problem.
Link: https://lore.kernel.org/r/20251118043042.27726-1-hs@nabladev.com
In dm_test_cmd_hash_md5 accidentially sha256 hash
ist used. Use the correct md5 hash instead.
Signed-off-by: Heiko Schocher <hs@nabladev.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
add sm3 256 hash support, so TPM2 chips which report
5 pcrs with sm3 hash do not fail with:
u-boot=> tpm2 autostart
tpm2_get_pcr_info: too many pcrs: 5
Error: -90
Signed-off-by: Heiko Schocher <hs@nabladev.com>
Implement SM3_256 Hash algorithm, based on
linux commit f83a4f2a4d8c: ("Merge tag 'erofs-for-6.17-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs")
Therefore add the needed parts from linux.
Signed-off-by: Heiko Schocher <hs@nabladev.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
sm3 crypto algorithm uses rol32 function from linux, so
import it. Linux base was:
commit ca91b9500108:("Merge tag 'v6.15-rc4-ksmbd-server-fixes' of git://git.samba.org/ksmbd")
Signed-off-by: Heiko Schocher <hs@nabladev.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Andrew Goodbody <andrew.goodbody@linaro.org> says:
The function clk_get_rate() returns a ulong with 0 meaning an invalid
clock rate and also negative error codes being returned for other
errors. But being an unsigned return value this cannot simply be tested
for with a < 0 test. Instead use the IS_ERR_VALUE() macro to check for
negative errors appearing as very large positive values. Fix those
places that test for <= 0. Also fix some places checking the return of
clk_register() that incorrectly used ERR_PTR().
Link: https://lore.kernel.org/r/20251021-clk_funcs-v1-0-acf51a40eea7@linaro.org
Testing an unisgned ivariable to be <= 0 will only detect the
case when it is 0. So correct this error test to a working version that
will behave as expected.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Testing an unisgned ivariable to be <= 0 will only detect the
case when it is 0. So correct this error test to a working version that
will behave as expected.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Heiko Schocher <hs@nabladev.com>
Testing an unisgned member of a struct to be <= 0 will only detect the
case when it is 0. So correct this error test to a working version that
will behave as expected.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Heiko Schocher <hs@nabladev.com>
clk_register() will return standard error codes so the use of ERR_PTR()
is incorrect. Furthermore the code was ineffective as it lacked a return
statement that would have actually made use of the result. Add the
return statement and remove the use of ERR_PTR to correct this.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Testing an unisgned member of a struct to be <= 0 will only detect the
case when it is 0. So correct this error test to a working version that
will behave as expected.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
clk_get_rate() returns a ulong and that return value is assigned to a
member of a struct that is an unsigned int. So testing this value to <=
0 will only detect a return of 0. Also the code in the if block assumes
ret holds the return value when it does not. So update the test to one
that will work as intended and update the if block to actually refer to
the return value.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Quentin Schulz <foss+uboot@0leil.net> says:
u-boot,boot-led and u-boot,error-led aren't actually handled by some
generic code but rather by board or architecture specific code. They
also aren't properties that are part of the official dt-binding so they
cannot be upstreamed. For u-boot,boot-led, there's actually a proper
replacement which is /options/u-boot/boot-led[1] (+ CONFIG_LED_BOOT=y).
For Rockchip boards, either nothing (for RK3066, PX30 and RK3399) was
using that property or (for RK3188) the code handling it was guarded by
symbols that were not enabled in the defconfig. For those, the property
and guarded code are removed.
For the Sam9x60 Curiosity, it seems that even though the LED is
controlled whenever CONFIG_LED is enabled, it isn't enabled by default
in the defconfig (but the code was added without modifying the
defconfig, explicitly leaving a choice to the user). I decided to keep
that feature by simply migrating it to the new API, though I cannot test
it as I do not own the device.
The STM32 boards will be migrated in the near future once their upstream
(kernel) Device Trees gain the new way to specify this (via
/options/u-boot/boot-led). I'll let Patrice handle this, see
https://lore.kernel.org/u-boot/94ed1988-13e8-4fe3-bdff-ba2c9973c556@foss.st.com/
and
https://lore.kernel.org/u-boot/2a3aa43a-ce19-41e1-ab56-556629ce5cf9@foss.st.com/
After this, only one user of u-boot,boot-led will be left, based on
STM32: board/dhelectronics/dh_stm32mp1/board.c. @Patrice, maybe that's
something you want to have a look at as well, this seems to be some
evaluation kit?
The only users of u-boot,error-led are STM32 boards, so I'll leave this
to Patrice as well, I do not know what's the way to go for that one.
In any case, I would like to not encourage people to use out-of-spec DT
properties when there is another option (u-boot,boot-led), so I remove
the properties from the dt-binding document from U-Boot.
The help text for the blink subcommand of the led command was misleading
so this is now fixed.
This also moves the content of doc/README.LED into the doc/api/led.rst,
while clearly stating one shouldn't be using this anymore.
This also gets rid of dt-binding that we already have in dts/upstream.
Finally, this adds documentation for the led shell command.
[1] https://github.com/devicetree-org/dt-schema/blob/v2025.08/dtschema/schemas/options/u-boot.yaml#L113-L116
Link: https://lore.kernel.org/r/20251112-led-old-dt-v1-0-2892d49517db@cherry.de
We're aiming to reduce the amount of U-Boot-specific and out-of-spec
Device Tree additions.
Those two properties haven't been doing anything for a long time
already, except when read by board files manually. This is still the
case for STM32 boards but those will be migrated in the near future
according to their maintainer. In any case, let's not encourage people
to add either of these properties to new or existing Device Trees and
remove it from the bindings.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
This board is one of the last users of /config/u-boot,boot-led property
which is a U-Boot property out of the DT spec.
Let's migrate it to use the in-spec /options/u-boot/boot-led property.
When enabling LED_BOOT, U-Boot proper will lit the LED right before
entering the main loop, so nothing needs to be done in board files.
As explained in the commit adding support for this u-boot,boot-led
property, let's keep backward compatibility in case LED_BOOT isn't
selected.
Note that this is not tested as I do not own this device.
Cc: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Tested-by: Alexander Dahl <ada@thorsis.com>
There's no code to make use of it.
Further more, the HW default state of that LED is on and migrating this
to the LED_BOOT implem brings no benefit as it'll stay on if U-Boot
reaches its main-loop. Blinking the LED_BOOT also doesn't help because
it doesn't blink for long enough to be noticeable before it's kept on.
This is by design, c.f.
https://source.denx.de/u-boot/u-boot/-/blob/v2025.10/include/led.h#L32-34
If we want this LED to be doing something different, it'll need to be
handled by a board file anyway.
Considering it hasn't worked in many years (if ever), let's just remove
it.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
There's no code to make use of it.
Further more, the HW default state of that LED is on and migrating this
to the LED_BOOT implem brings no benefit as it'll stay on if U-Boot
reaches its main-loop. Blinking the LED_BOOT also doesn't help because
it doesn't blink for long enough to be noticeable before it's kept on.
This is by design, c.f.
https://source.denx.de/u-boot/u-boot/-/blob/v2025.10/include/led.h#L32-34
If we want this LED to be doing something different, it'll need to be
handled by a board file anyway.
Considering it hasn't worked in many years, let's just remove it.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
There's not a single device making use of that code and it anyway
shouldn't be using the old deprecated u-boot,boot-led /config property
anymore but rather boot-led from /options/u-boot[1] Device Tree node.
Because spl_board_init() is only present to call this now removed
function, we can remove it as well as SPL_BOARD_INIT which is the symbol
guarding calls to spl_board_init() (which is now also removed).
[1] https://github.com/devicetree-org/dt-schema/blob/v2025.08/dtschema/schemas/options/u-boot.yaml#L113-L116
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
This property is only read in arch/arm/mach-rockchip/rk3188/rk3188.c
when CONFIG_SPL_LED is enabled, which isn't the case for this board, so
let's remove dead code.
Additionally, if we ever want to enable this LED as Boot LED, we should
instead be using boot-led phandle property in /options/u-boot[1] Device
Tree node with the "new" LED UCLASS devices.
[1] https://github.com/devicetree-org/dt-schema/blob/v2025.08/dtschema/schemas/options/u-boot.yaml#L113-L116
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
doc/device-tree-bindings/leds/leds-bcm6328.txt can be found at
dts/upstream/Bindings/leds/leds-bcm6328.yaml.
doc/device-tree-bindings/leds/leds-bcm6358.txt can be found at
dts/upstream/Bindings/leds/leds-bcm6358.txt.
doc/device-tree-bindings/leds/leds-gpio.txt can be found at
dts/upstream/Bindings/leds/leds-gpio.yaml.
doc/device-tree-bindings/leds/leds-lp5562.txt can be found at
dts/upstream/Bindings/leds/leds-lp55xx.yaml.
Only two LED dt-bindings are left in U-Boot: leds-bcm6858.txt and
leds-pwm.txt. The former is partially supported by
dts/upstream/Bindings/leds/leds-bcm63138.yaml but is lacking all
optional properties we have listed in "downstream" dt-binding in U-Boot.
However, there doesn't seem to exist any user of that compatible.
The latter is partially supported by
dts/upstream/Bindings/leds/leds-pwm.yaml but is missing the
u-boot,default-brightness property, which is used by
arch/arm/dts/rk3326-odroid-go2-u-boot.dtsi at the moment. The
default-brightness property is probably not what we want here as it
defaults to max-brightness if missing. I'm assuming we want a different
value for U-Boot (127) and the kernel (255 via max-brightness as a
default), which would prevent us from upstreaming this property, which
doesn't change the status quo, so let it be for now.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
This moves the content of the legacy LED API from doc/READ.LED to
doc/api/led.rst, applying minimal cosmetic changes to "nicely" integrate
it with the current docs and adding a small introduction to the legacy
API section.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
The blink subcommand actually requires an additional parameter
(blink-freq) but not the others.
In order to simplify the help text, split the blink subcommand help text
from the off|on|toggle subcommands.
Then, fix the help text so that it is clear that the frequency is
required.
While at it, specify the duty cycle.
Fixes: ffe2052d6e ("dm: led: Add a new 'led' command")
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
The problem we face currently with Azure jobs is that we're running out
of disk space on the runners as we build. There's not a good way to
split approximately 1500 configurations across 10 jobs and not be close
to or exceeding that limit. Split this in to 29 jobs instead with a goal
of averaging an hour per job. This split gets us close, but there are
still some challenging jobs to try and break up further. The list is
mostly alphabetized but with some intentional changes (catch-all are
last, mx/imx are together, SoC family splits are just grouped together).
The average build time should be close to the same, but outliers can and
will happen.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Bump to noble-20251013
- Include tools for sage lab, build TF-A for platforms there.
- Switch to distro provided trace-cmd, add libengine-pkcs11-openssl
- Use mirrors for GNU projects
- Switch to QEMU 10.1.x
Signed-off-by: Tom Rini <trini@konsulko.com>
