Since most boards now use the same generic device config header, move its
setup to SoC Kconfig instead of setting SYS_CONFIG_NAME in each board's
Kconfig.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The LG Optimus 2X is a touchscreen-based, slate-sized smartphone designed
and manufactured by LG that runs the Android operating system. The
Optimus 2X features a 4" WVGA display, an Nvidia Tegra 2 dual-core chip,
512 MB of RAM and extendable 8 GB of internal storage. UART-B is default
debug port.
Tested-by: Ion Agorria <ion@agorria.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Add support for Skyworks AAT2870 LED Backlight Driver and Multiple LDO
Lighting Management Unit. Only backlight is supported as for now. Supported
backlight level range is from 2 to 255 with step of 1.
Tested-by: Ion Agorria <ion@agorria.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
LG LH400WV3-SD04 is a color active matrix TFT (Thin Film Transistor)
liquid crystal display (LCD). The resolution of a 4" contains 480 x 800
pixels.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Hitachi TX10D07VM0BAA is a color active matrix TFT (Thin Film Transistor)
liquid crystal display (LCD). The resolution of a 4" contains 480 x 800
pixels.
Tested-by: Ion Agorria <ion@agorria.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Add support for 8-bit CPU driven (primary and secondary) display signal
interface found in Tegra 2 and Tegra 3 SoC.
Tested-by: Ion Agorria <ion@agorria.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
MAX8907 PMIC has embedded poweroff function used by some device to initiane
device power off. Implement it as optional sysreset driver guarded by
kconfig option and system-power-controller device tree property.
Tested-by: Ion Agorria <ion@agorria.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Added a new regulator driver for the MAXIM MAX8907 PMIC, providing
essential regulator functionalities and incorporated the necessary binding
framework within the core PMIC driver.
Tested-by: Ion Agorria <ion@agorria.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Releasing a GPIO on Tegra necessitates changing its configuration to SFIO
to activate its special function. Without this reconfiguration, the special
function will be unavailable.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Add fit_addr_r to the environment to allow us to boot from a FIT image.
Increase the maximum Image size from 23 MB to 26 MB by moving the
initramfs start address up. This gives us a bigger ranger to
provide kernel images which are not stripped down too much.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
'net_fetch_cmd' is not defined by the K3 board files. They
use the more common 'get_cmd' from NXP products.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Extensions are now handled by the board-code. Remove this non-existing
function to proper boot from network.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
The bootstd code itself does not have any dependency on BLK in order to
build. However, in order to minimize size growth of non-migrated
platforms, change this from being "default y" to "default y if BLK".
This will make it easier to begin migration of platforms which do not
have any BLK-class device but do want to use bootstd.
Signed-off-by: Tom Rini <trini@konsulko.com>
!A || (A && B) is equivalent to !A || B
Drop the unused middle expression to simplify the statement.
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Write enable(06h) command will be sent to a flash device to
set the write enable latch bit before every program, erase,
write command. After that write disable command (04h) needs
to be sent to clear the write enable latch.
This write_disable() is missing at the majority of the places
in the driver, add it to clear write enable latch.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://gist.github.com/PrasanthBabuMantena/c12f39744de188a9d08cd5ca51dc2a7b
Tested-by: Prasanth Babu Mantena <p-mantena@ti.com>
MT35XU512ABA has only BFPT and 4-Byte Address Instruction Table
in SFDP. commit bebdc23750 ("mtd: spi-nor: Parse SFDP SCCR Map")
added checks in spi_nor_octal_dtr_enable() to bail out if the 22nd DWORD
in SCCR does not indicate DTR Octal Mode Enable, since MT35XU512ABA device
supports octal DTR mode, add this property in SFDP fixup.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Prasanth Babu Mantena <p-mantena@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Make sure unused exfat_humanize_bytes() and exfat_print_info()
functions are not compiled into U-Boot code base. This also removes
CID 550300: Integer handling issues (INTEGER_OVERFLOW)
in exfat_humanize_bytes() , which is now surely unreachable.
Signed-off-by: Marek Vasut <marex@denx.de>
In case the filename is too long, longer than PATH_MAX - 1, it
would overflow dirs->dirname array. Add missing check and also
use strncpy() to prevent the overflow in any case.
Fixes CID 550305: Security best practices violations (STRING_OVERFLOW)
Signed-off-by: Marek Vasut <marex@denx.de>
On K3 devices two drivers ti_sci and ti_sci_dm are supporting firmware
functions. At run time one of driver is used.
Driver ti_sci already initializing head for dev_list in its probe
function, but it was missed in ti_sci_dm driver.
So add head list init support for ti_sci_dm driver.
While at this, move init of list before usages in both functions.
Fixes: 5d5a699855a7("firmware: ti_sci: Add support for Resoure Management at R5 SPL stage")
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
This config was defined with the default value of 8 MiB. However,
the default value is different when CONFIG_ARM64 is enabled and
should be 64 MiB.
Remove this config from the A53 defconfig and use the correct
default config.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Job IDs are positive integers greater than 1. 0 is not a valid job ID,
therefore fix the comparison in do_wait().
Fixes Coverity defects:
*** CID 550296: Control flow issues (NO_EFFECT)
/cmd/spawn.c: 172 in do_wait()
166 for (i = 0; i < CONFIG_CMD_SPAWN_NUM_JOBS; i++)
167 if (job[i])
168 ret = wait_job(i);
169 } else {
170 for (i = 1; i < argc; i++) {
171 id = dectoul(argv[i], NULL);
>>> CID 550296: Control flow issues (NO_EFFECT)
>>> This less-than-zero comparison of an unsigned value is never true.
"id < 0UL".
172 if (id < 0 || id >
CONFIG_CMD_SPAWN_NUM_JOBS)
173 return CMD_RET_USAGE;
174 idx = (int)id - 1;
175 ret = wait_job(idx);
176 }
177 }
*** CID 550297: Integer handling issues (INTEGER_OVERFLOW)
/cmd/spawn.c: 174 in do_wait()
168 ret = wait_job(i);
169 } else {
170 for (i = 1; i < argc; i++) {
171 id = dectoul(argv[i], NULL);
172 if (id < 0 || id >
CONFIG_CMD_SPAWN_NUM_JOBS)
173 return CMD_RET_USAGE;
>>> CID 550297: Integer handling issues (INTEGER_OVERFLOW)
>>> Expression "idx", where "(int)id - 1" is known to be equal to -1,
overflows the type of "idx", which is type "unsigned int".
174 idx = (int)id - 1;
175 ret = wait_job(idx);
176 }
177 }
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
CC: Tom Rini <trini@konsulko.com>
Clang's preprocessor may emit extra spaces for lines starting with '#'.
Lines with these extra characters cannot be handled by Kconfig and will
be ignored with warnings like,
unexpected data: # CONFIG_OF_BOARD_FIXUP is not set
Those options that is expected to be assigned explicitly with N will be
set to the default value, messing up board configurations.
Let's sed these spaces away to ensure board configurations could be
correctly generated with Clang.
Link: https://github.com/llvm/llvm-project/issues/78778
Fixes: 2027e99e61 ("Makefile: Run defconfig files through the C preprocessor")
Reported-by: Nathaniel Hourt <I@nathaniel.land>
Signed-off-by: Yao Zi <ziyao@disroot.org>
Introduce support for env in generic MTD. Currently we only support SPI
flash based on the lagacy sf cmd that assume SPI flash are always NOR.
This is not the case as to SPI controller also NAND can be attached.
To support also these flash scenario, add support for storing and
reading ENV from generic MTD device by adding an env driver that
base entirely on the MTD api.
Introduce a new kconfig CONFIG_ENV_IS_IN_MTD and
CONFIG_ENV_MTD_DEV to define the name of the MTD device as exposed
by mtd list.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Currently, when decompressing a gzip-compressed image during bootm, a
generic error such as "inflate() returned -5" is shown when the buffer is
too small. However, it is not immediately clear that this is caused by
CONFIG_SYS_BOOTM_LEN being too small.
This patch improves error handling by:
- Detecting Z_BUF_ERROR (-5) returned from the inflate() call
- Suggesting the user to increase CONFIG_SYS_BOOTM_LEN when applicable
- Preserving the original return code from zunzip() instead of overwriting
it with -1
By providing clearer hints when decompression fails due to insufficient
buffer size, this change helps users diagnose and fix boot failures more
easily.
Signed-off-by: Aristo Chen <aristo.chen@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Since 7506c15, HOST_ARCH is now used by the EFI loader even when
CONFIG_SANDBOX is disabled. When cross-compiling, the Makefile defines
HOST_ARCH based on the cross-compiler prefix, but this definition fails
to cover some common compiler prefixes. When cross-compiling U-Boot in
nixpkgs, we use CROSS_COMPILE=armv6l-unknown-linux-gnueabihf-, which
results in HOST_ARCH being undefined and causes a build failure.
Fix this by adding armv6l to the match for ARM. Also add armv5tel,
as this is another possible ARM compiler prefix.
Signed-off-by: ZHANG Yuntian <yt@radxa.com>
Signed-off-by: Ben Wolsieffer <benwolsieffer@gmail.com>
- CI: https://source.denx.de/u-boot/custodians/u-boot-stm/-/pipelines/26081
- STM32 MCUs:
- Fix console cmdline
- Add support NT35510 panel controller on stm32f769i-disco board
- Fix dfu alt buffer clearing
- Enable scan and start for AB schema on STM32MP15 DHSOM
- Add stm32mp2 support for dwc_eth_qos
ubi fixes for v2025.07-rc2
- fix bug: Put MTD device after it is not used
drop MTD device reference after it is not longer used!
port from upstream Linux commit: b95f83ab762dd6211351b9140f99f43644076ca8
from Alexander Vickberg
The Linux cmdline encoded in the defconfig is wrong, the
STM32 USART driver registers as ttySTM0 not ttyS0.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The Linux cmdline encoded in the defconfig is wrong, the
STM32 USART driver registers as ttySTM0 not ttyS0.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The Linux cmdline encoded in the defconfig is wrong, the
STM32 USART driver registers as ttySTM0 not ttyS0.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The Linux cmdline encoded in the defconfig is wrong, the
STM32 USART driver registers as ttySTM0 not ttyS0.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The Linux cmdline encoded in the defconfig is wrong, the
STM32 USART driver registers as ttySTM0 not ttyS0.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The Linux cmdline encoded in the defconfig is wrong, the
STM32 USART driver registers as ttySTM0 not ttyS0.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The set_dfu_alt_info() function calls the ALLOC_CACHE_ALIGN_BUFFER()
macro to declare a `buf' variable pointer into an array allocated on the
stack. It then calls the memset() function to clear the useable portion
of the array using the idiomatic expression `sizeof(buf)'.
While this would indeed work fine for an array, in the present case we
end up clearing only the size of a pointer.
Fix this by specifying the explicit size `DFU_ALT_BUF_LEN' instead.
Fixes: ec2933e543 ("board: stm32mp1: move set_dfu_alt_info in st common directory")
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Support FRIDA FRD400B25025-A-CTK display on stm32f769-disco board.
As reported in the section 8.3 (i. e. Board revision history) of document
UM2033 (i. e. Discovery kit with STM32F769NI MCU) these are the changes
related to the board revision addressed by the patch:
- Board MB1166 revision A-09:
- LCD FRIDA FRD397B25009-D-CTK replaced by FRIDA FRD400B25025-A-CTK
This means that the MB1166-A09 is using an NT35510 panel controller,
unlike the previous versions which use an OTM8009A controller.
Therefore, let's add support for NT35510 panel handling to the
stm32f769-disco board configurations.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
[backport from Linux commits 9b26d5c044d6a29ebfb1845408e0f2a7c5f89818
and 219a1f49094f50bf9c382830d06149e677f76bed]
The patch adds the FRIDA FRD400B25025-A-CTK panel, which belongs to the
Novatek NT35510-based panel family.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
[backport from Linux commit db4fc2c79c533986795a7750e9a12caf9d620b48]
As reported in the section 8.3 (i. e. Board revision history) of document
UM2033 (i. e. Discovery kit with STM32F769NI MCU) these are the changes
related to the board revision addressed by the patch:
- Board MB1166 revision A-09:
- LCD FRIDA FRD397B25009-D-CTK replaced by FRIDA FRD400B25025-A-CTK
The patch adds the DTS support for the new display which belongs to the
the Novatek NT35510-based panel family.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
For the STM32MP15 DHSOM, change the default environment so an AB schema
on a device can be detected.
For this the define "SCAN_DEV_FOR_BOOT_PARTS" is overwritten and
appended.
The detection works by looking for the partitions with specific lables.
The name of those partitions are in the variables and its defaults:
* dh_ab_partname_primary=rootfs-a
* dh_ab_partname_secondary=rootfs-b
To prevent being hanging at bootcmd, enable "CONFIG_BOOT_RETRY" and
"CONFIG_RESET_TO_RETRY", but the timer will only be activated, if the AB
partitions are detected.
Signed-off-by: Pascal Zimmermann <pzimmermann@dh-electronics.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Make it possible to substitute the 'part list' command inside
'scan_dev_for_boot_part' with a custom board specific implementation.
For this the new define 'SCAN_DEV_FOR_BOOT_PARTS' is introduced.
Signed-off-by: Pascal Zimmermann <pzimmermann@dh-electronics.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The MTD device reference is dropped via put_mtd_device, however its
field ->index is read and passed to ubi_msg. To fix this, the patch
moves the reference dropping after calling ubi_msg.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Upstream Linux commit: b95f83ab762dd6211351b9140f99f43644076ca8
Signed-off-by: Alexander Vickberg <wickbergster@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
For Ethernet to work on the RZ/G2L board, we need to enable support for
the ksz9131 PHY and enable random MAC address generation (as no MAC
address is programmed into the board).
We also enable the `dhcp`, `mii` and `ping` commands so that Ethernet
functionality can be tested and used to boot Linux.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The Renesas R9A07G044L (RZ/G2L) SoC includes two Gigabit Ethernet
interfaces which can be supported using the ravb driver. Some RZ/G2L
specific steps need to be taken during initialization due to differences
between this SoC and previously supported SoCs. We also need to ensure
that the module reset is de-asserted after the module clock is enabled
but before any Ethernet register reads/writes take place.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
