i.MX95 uses the same USB IP as i.MX8MM. It can then reuse the ehci-mx6
driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Based on 335799b725 ("usb: dwc2: Use regulator_set_enable_if_allowed")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Based on 335799b725 ("usb: dwc2: Use regulator_set_enable_if_allowed")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Pull request efi-next-20250105
Documentation:
* doc: develop: Fix typos and wording in binman/binman.rst
* doc: develop: Fix typos and wording in gdb.rst
* doc: sandbox: Fix the "sb" command name
* doc/develop/distro.rst: Better document upstream definition of extlinux.conf
UEFI:
* efi_loader: avoid writing message in Exit() boot service
* efi_loader: update EFI specification version
* cmd: efidebug: update output of memory attributes
* efi_loader: Don't warn if the TCG2 FinalEvents table is not installed
* cmd: bootmenu: add parameter -e for UEFI boot options
* efi_loader: Update startimage_exit self-test to check error
* efi: Correct ECPT table GUID
Others:
Building the API demo application for riscv64 is supported.
* API: unify platform_sys_info() implementations
* examples: implement _start and syscall for RISC-V
* examples: use architecture specific memset() on RISC-V
* examples: use QEMU compatible LOAD_ADDR on RISC-V
* test: fix test_extension.py
* configs: sandbox_deconfig: remove CONFIG_AMIGA_PARTITION
* CI: xilinx_versal_virt: disable USB_DWC3
* net: eth_bootdev_hunt() should not run DHCP
Judith Mendez <jm@ti.com> says:
This patch series adds config options for Sitara K3 boards
to support MMC UHS modes.
While testing with SD card boot and eMMC boot,
found missing eMMC boot support for am62ax in am62a7_init,
patch 1/7, and missing config option to support eMMC boot.
While we are here, for am62ax, enable config option to
change MMC bus modes and enable r5 SDHCI ADMA for faster boot
time.
Also for all k3 Sitara boards, cleanup MMC ENV configs that
are no longer needed since we no longer load env from MMC
device.
Link: https://lore.kernel.org/r/20241220203704.2076499-1-jm@ti.com
First, the "Boot Loader Specification" link has moved to a new location,
so link to that directly. Second, that link does not document as much of
the extlinux.conf format as I recall the old version doing at least.
However, the Syslinux Project wiki is the current location of the documentation
linked to in doc/README.pxe and also has a reference for SYSLINUX. Link
to both of these.
Signed-off-by: Tom Rini <trini@konsulko.com>
UEFI specification 2.11 has been published.
There are no changes relevant for the U-Boot scope.
So let us update the supported specification version.
Change the comment for the constant to Sphinx style.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This is done so that the device path protocol interface of the network
device can be changed internally by u-boot when a new bootfile gets
downloaded.
Signed-off-by: Adriano Cordova <adriano.cordova@canonical.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The command name was "sbi" instead of "sb" in "doc/usage/cmd/sb.rst",
the file documenting the "sb" command. It is annoying, because the
index in the left panel on the
<https://docs.u-boot.org/en/latest/usage/cmd/sb.html> page shows no
"sb" command, which makes difficult to navigate to the "sb"
documentation.
Fixed the command name: "sbi" -> "sb".
Fixes: ec6d30649c (doc: sandbox: Add docs for the sb command, 2024-10-28)
Signed-off-by: Olivier L'Heureux <olivier.lheureux@mind.be>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fix provided by 997fc12ec9 is actually introducing
a buffer overrun, and the overrun is effective if the
memory after the reloc section is not zeroed.
Probably that's why this bug is not always noticeable.
The problem is that 8-bytes 'rel' pointer can be 4-bytes aligned
according to the PE Format, so the actual relocate function can
take values after the reloc section.
One example is the following dump from the reloc section:
bce26000: 3000 0000 000c 0000 0000 0000 0000 0000
bce26010: 7c00 9340 67e0 f900 1c00 0ea1 a400 0f20
This section has two relocations at offset bce26008 and bce2600a,
however the given size (rel_size) for this relocation is 16-bytes
and this is coming form the efi image Misc.VirtualSize, so in this
case the 'reloc' pointer ends at affset bce2600c and is taken as
valid and this is where the overflow is.
In our system we see this problem when we are starting the
Boot Guard efi image.
This patch is fixing the overrun while preserving the fix done
by 997fc12ec9.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@belden.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
When the TCG2 protocol installation fails, we are trying to remove
all the objects we created in tcg2_uninit().
However, there are cases when this function runs before the config
table was installed. So instead of printing an error unconditionally
check against EFI_NOT_FOUND and don't print anything if the table wasn't
installed to begin with.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The bootmenu command can display
* menu entries defined by environment variables
* menu entries defined by UEFI boot options
Not in all cases showing the UEFI boot options is desired.
Provide a new parameter '-e' to select the display of UEFI boot options.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Currently when booting dhcp_run() may be executed multiple times:
once in eth_bootdev_hunt() and once in the network booting bootmeth.
We need to call eth_bootdev_hunt() when setting up the EFI sub-system to
supply the simple network protocol. We don't need an IP address set up.
We can reduce the bootime by not executing dhcp_run() in
eth_bootdev_hunt().
Furthermore eth_bootdev_hunt() with autostart=yes leads on the legacy
network stack leads to downloading a file via TFTP and to booting the
downloaded file.
Instead of running dchp_run() just check that there is a network device
in eth_bootdev_hunt().
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The CI uses the following command to launch xilinx_versal_virt_defconfig:
qemu-system-aarch64 -M xlnx-versal-virt \
-display none -m 4G -serial mon:stdio \
-device loader,file=u-boot,cpu-num=0
'usb start' or invoking eth_bootdev_hunt leads to a crash when function
dwc3_core_init() tries to access a register at offset 0xc704 (DWC3_DCTL)
relative to the register start address 0xfe20c100.
Disable CONFIG_USB_DWC3 in the CI until the driver problem is fixed.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
We do not actually test the code.
Scanning for Amiga partitions of the sandbox is extremely slow,
especially on the partially implemented USB device.
For build testing the other sandbox defconfigs are good enough.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
test_extension.py assumes that no extension is known at test start.
This assumption is wrong because we do not come out of reboot.
A prior test may have already hunted for the extension bootdev.
Remove the invalid assert.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
We should not write messages in UEFI API functions. This may lead to
incorrect screen layout in UEFI application.
For single statements after if clause we don't need braces.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
On some RISC-V including QEMU $loadaddr is 0x80200000.
For bootelf to work choose a different LOAD_ADDR to which the demo ELF
binary is relocated.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
To build the API examples on RISC-V we need to
implement _start and syscall for RISC-V.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
ARM, MIPS, and RISCV can use the same implementation of
platform_sys_info(). PPC provides some extra information.
So keep it separate.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add the basic 'hello world ta' command which increment
of the value passed. This provides easy test for
establishing a session with OP-TEE TA and verify.
It includes following "hello world ta" subcommands:
optee hello; default value '0' is passed and gets incremented.
optee hello <value>; value to increment via OP-TEE HELLO
WORLD TA.
To enable the OP-TEE side HELLO WORLD example please refer
https://optee.readthedocs.io/en/latest/building/gits/optee_examples/optee_examples.html
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Jerome Forissier <jerome.forissier@linaro.org>
Enable MMC_SPEED_MODE_SET config option in defconfig to enable
changing MMC bus modes with mmc rescan for am62ax device.
Signed-off-by: Judith Mendez <jm@ti.com>
When a successful neighbor advertisement is received, the ethernet
address should be saved for later use to avoid having to redo the
neighbor discovery process.
For example, with TFTP the address should get saved into
"net_server_ethaddr". This is being done correctly with ARP for IPv4,
but not for neighbor discovery with IPv6.
Signed-off-by: Sean Edmond <seanedmond@microsoft.com>
Reviewed-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
timeout_count is never reset once a tftpput transfer has started. If for
whatever reason timeouts occur frequently, but the server keeps replying
nonetheless, the transfer may be needlessly aborted.
Reset timer_count on reception of an ACK to avoid this situation.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Linux DTS compatible MDIO bitbanging driver.
Both clause 22 and clause 45 MDIO supported and validated.
Heavily based on the Linux drivers (more or less the same code base).
Signed-off-by: Markus Gothe <markus.gothe@genexis.eu>
This reverts commit 431be621c6.
Section 3.3 of Reduced Gigabit Media Independent Interface (RGMII)
Version 2.0 (4/1/2002) details that a PHYs using a ~2ns internal delay
are referred to as RGMII-ID. This internal delay is optional.
Page 147-148 of the Marvell Doc. No. MV-S107146-U0 Rev. F details
timings of the RX/TX delays. We see that with the TX/RX_CLK delay
enabled, our RX/TX_CTL signal is shifted w.r.t CLK to reflect the delay
added.
In 431be62 there is no timing difference between RGMII and RGMII-ID, and
so programmers wanting to explicitly set their PHY to RGMII will find
that delay added anyway. This could throw off timing if that internal
delay is undesired.
We should be handling all 4 possible RGMII cases of PHY_INTERFACE_MODE:
RGMII, RGMII_ID, RGMII_TXID, and RGMII_RXID. Reverting 431be62
implements this.
See also m88e1111_config_init_rgmii_delays in the equivalent driver in
Linux (drivers/net/phy/marvell.c), which does not set these delays in
RGMII mode.
68e6eca was tested out on an 88E1512 PHY in RGMII-ID mode. This
reversion has been tested by myself on an 88E1518 in RGMII-ID mode. This
patch affects boards using this driver in "rgmii" mode, as the internal
delay will no longer be enabled. Namely kikwood-nsa310s.
Signed-off-by: Rufus Segar <rhs@riseup.net>
We have a some boards that rarely starts networking abnormally, so there are
many timeouts during file transfer. In the same time there is a normal transfer
between timeouts. In this case we can continue transfer (instead of connection
aborting) by just clearing timeout counter on every successful block.
This patch does not affect the case when several timeouts happen one after
another. The transfer will be aborted. Thus the transfer will be
continued in the case of unstable link, but will be aborted in the case
of inaccessible server.
Feature downside: it may greatly slowdown (instead of abort) file transfer
in the case of unstable link.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
