In memac_wait_until_free and memac_wait_until_done the use of
post-decrement on the test in the while loop for a timeout means that
timeout will be equal to -1 on exit in that case. Adjust the test for
this expected value.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In fm_eth_bind there is a dereference of dev before it is NULL checked.
Add a NULL check before the first dereference and remove a later NULL
check that is now redundant.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In bmi_rx_port_disable and bmi_tx_port_disable the use of post-decrement
on the test in the while loop for a timeout means that timeout will be
equal to -1 on exit in that case. Adjust the test for this expected
value.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In the case of !zq_en zqcs_init is never assigned to although its value
is used. Correct by initialising zqcs_init to 0.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This commit introduces a new API,
request_firmware_into_buf_via_script(), to the fs_loader framework.
This function allows firmware to be loaded into memory using
a user-defined U-Boot script, providing greater flexibility for
firmware loading scenarios that cannot be handled by static file
paths or device/partition selection alone.
Key features:
- The API runs a specified U-Boot script (by name), which is responsible
for loading the firmware into memory by any means (e.g., load from MMC, USB, network, etc.).
- The script must set two environment variables: 'fw_addr'
(the memory address where the firmware is loaded) and
'fw_size' (the size of the firmware in bytes).
- The function validates these variables, copies the firmware into a newly
allocated buffer (using memdup), and returns the pointer
via the provided double pointer argument.
- The maximum allowed firmware size is checked to prevent buffer overflows.
- The environment variables are cleared after use to avoid stale data.
- Detailed error messages are provided for all failure conditions to aid debugging.
Usage example:
1. Define a U-Boot script in the environment that loads the firmware
and sets the required variables:
=> env set my_fw_script 'load mmc 0:1 ${loadaddr} firmware.bin &&
env set fw_addr ${loadaddr} && env set fw_size ${filesize}'
2. In your code, call the new API:
void *fw_buf = NULL;
int ret = request_firmware_into_buf_via_script(&fw_buf, 0x46000000, "my_fw_script");
if (ret < 0)
return ret;
This approach allows board integrators and users to customize the firmware
loading process without modifying the source code,
simply by changing the script in the U-Boot environment.
Signed-off-by: Lucien.Jheng <lucienzx159@gmail.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[trini: Fix printf of size_t needing to use %zx]
Signed-off-by: Tom Rini <trini@konsulko.com>
Drop SUPPORT_EXTENSION_SCAN and enable PHYTEC_SOM_DETECTION_BLOCKS
to align with other PHYTEC platforms. These options were missed when
phyCORE-AM62Ax support was added.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Use CONFIG_PHYTEC_EEPROM_BUS instead of the hard coded value for the i2c bus.
Signed-off-by: Dominik Haller <d.haller@phytec.de>
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Add the option to choose a different bus number than 0 for the i2c eeprom
based som detection.
Signed-off-by: Dominik Haller <d.haller@phytec.de>
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Configure RMMI and M-PHY registers for HS mode required for selection of
bit rate series A or B. If it is not a calibrated part, then switch back
to SLOWAUTO_MODE and skip all these configurations.
Implemented below sequence as per the DWC RMMI databook.
1. Override RMMI CBRATESEL with the desired rate.
2. Set TX_CFGUPDT_0 to 1'b1 for one TX_CFGCLK_0 cycle.
3. Override PHY rx_req to 1, then poll on PHY rx_ack register till it
goes 1(both lanes).
4. Override PHY rx_req to 0, then poll on PHY rx_ack register till it
goes 0(both lanes).
5. Remove PHY rx_req override(both lanes).
6. Start the LS PMC.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250724044402.260149-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The existing compatible name for U-Boot's k3 system controller driver
i.e "ti,am625-system-controller" has been added to linux[1] device-tree.
This compatible in kernel is meant for configuring the Control Module
registers (CTRL_MMR0).
However in U-Boot, the matching driver was being used to load the system
firmware on the secure M-cores by the R5 SPL and therefore must be
updated to a different compatible to avoid conflicts.
Therefore, this patch renames all references of the compatible to
"ti,am654-tisci-rproc-r5". The "-r5" is appended so as to avoid any
future conflicts since r5 specific compatibles should only be useful for
U-Boot.
[1]: 5959618631fe ("dt-bindings: mfd: ti,j721e-system-controller: Add compatible string for AM654")
https://lore.kernel.org/r/20250421214620.3770172-2-afd@ti.com
Signed-off-by: Anshul Dalal <anshuld@ti.com>
Add rauc to bootmeths variable if BOOTMETH_RAUC is enabled.
This is setting a proper default for RAUC enabled systems.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Martin Schwan <m.schwan@phytec.de>
Since the bootmeth "rauc" is not a global boot method, do not select the
corresponding BOOTMETH_GLOBAL option.
Signed-off-by: Martin Schwan <m.schwan@phytec.de>
Initially, only one STM32MP25 based board was available, the
stm32mp257f-ev1 board which was set by default in stm32mp25_defconfig.
Since commit 79f3e77133 ("Subtree merge tag 'v6.16-dts' of dts repo [1] into dts/upstream")
we inherited of a second MP25 based board which is the stm32mp257f-dk board.
Enable OF_UPSTREAM_BUILD_VENDOR and set OF_UPSTREAM_VENDOR to allow all
STMicroelectronics DT compilation.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Avoid unlimited while loop by adding a timeout. The timeout is
calculated based on a minimal throughput of 256 KB/s.
The timeout is set at least to 2 seconds.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
File system such as YAFFS2 need to know the number of available
OOB bytes per page to be able to choose if they should locate their
metadata in the data area or in the spare area.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
In zynqmp_pinconf_set if param is PIN_CFG_IOSTANDARD or
PIN_CONFIG_POWER_SOURCE and zynqmp_pm_pinctrl_get_config returns an
error then value will not be assigned to when its value is tested to be
not equal to arg. Add code to only test value not equal to arg if ret is
false.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Link: https://lore.kernel.org/r/20250807-pinctrl_misc-v1-4-eeb564a1b032@linaro.org
Signed-off-by: Michal Simek <michal.simek@amd.com>
tpm_tis_i2c_get_burstcount returns a size_t but also returns -EBUSY if
the TPM is surrently busy. As size_t is an unsigned type simply testing
for < 0 will not work so change the test for being equal to -EBUSY which
will work. Also remove the trivial comments.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
When printing the contents of an size_t variable we need to use z prefix
to the format character in order to get the correct format type
depending on 32 or 64bit-ness.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
When printing the contents of an size_t variable we need to use z prefix
to the format character in order to get the correct format type
depending on 32 or 64bit-ness.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Use GUSBCFG_FORCEHOSTMODE to detected the HOST forced mode as it is done
in the Linux driver drivers/usb/dwc2/core.c:dwc2_core_reset().
The host polling must be executed only if the current mode is host,
either due to the force HOST mode (which persists after core reset)
or the connector id pin.
The GUSBCFG_FORCEDEVMODE bits is used to force the device mode (for
example used on STM32MP1x platform) and when it is activated the DWC2 reset
failed with the trace:
"dwc2_core_reset: Waiting for GINTSTS_CURMODE_HOST timeout"
Fixes: c5d685b899 ("usb: dwc2: Unify flush and reset logic with v4.20a support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Junhui Liu <junhui.liu@pigmoral.tech>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Marek Vasut <marek.vasut@mailbox.org>
