The family of PCA9450 PMICs have the ability to perform system resets.
Restarting via PMIC is preferred method of restarting the system as all
the peripherals are brought to a know state after a power-cycle. The
PCA9450 features a cold restart procedure which is initiated by an I2C
command 0x14 to the SW_RST register.
Support in Linux for restarting via PCA9450 PMIC has been added by
Linux commit 6157e62b07d9 ("regulator: pca9450: Add restart handler").
Now add support for it also in the U-Boot via sysreset framework.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Paul Geurts <paul.geurts@prodrive-technologies.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
exynos_power_init sets up regulators for the emmc and sdcard, but
these regulators are already marked as always-on and boot-on and hence
are handled already by the regulator-uclass. Since we currently try to
set them up twice we get error -114 (EALREADY) from exynos_power_init
on every boot:
LDO20@VDDQ_EMMC_1.8V: set 1800000 uV; enabling (ret: -114)
LDO22@VDDQ_EMMC_2.8V: set 2800000 uV; enabling (ret: -114)
LDO21@TFLASH_2.8V: set 2800000 uV; enabling (ret: -114)
Remove the superfluous exynos_power_init to silence these errors.
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Linux uses just regulators { }; instead of voltage-regulators { };, so
this change aligns the DTSes found in the two projects.
The max8997 driver does not yet parse the regulators node, so we can
safely change its name without breaking anything.
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
All u-boot users now use maxim,max8997-pmic instead, as does Linux's
DTSes, so we can now safely drop the maxim,max8997 compatible.
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Instead of maxim,max8997. Linux uses maxim,max8997-pmic, so with this
change we align the trats DTS with its linux counterpart.
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Linux's DTSes uses maxim,max8997-pmic, so check for this compatible
as well so that max8997 pmic driver can support both u-boot and
Linux's DTSes.
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Linux uses just regulators { }; instead of voltage-regulators { };, so
this change aligns the DTSes found in the two projects.
The max8998 driver does not yet parse the regulators node, so we can
safely change its name without breaking anything.
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Linux uses just regulators { }; instead of voltage-regulators { };, so
this change aligns the DTSes found in the two projects.
The max8998 driver does not yet parse the regulators node, so we can
safely change its name without breaking anything.
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
All devicetrees that use s2mps11 driver have been converted to use
regulators { };, so we can safely drop the voltage-regulators fallback
check.
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With this both linux and u-boot uses the same node name, which
simplifies devicetree parsing in s2mps11 driver.
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Linux's DTSes uses regulators { }; while u-boot's DTSes uses
voltage-regulators { };. Look for regulators, and fallback to
voltage-regulators if not found, so that both type of DTSes can be
used with the driver.
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The sd-vsel-gpios property in the root of the PMIC node is deprecated
and therefore not parsed by the driver anymore. We can safely remove
this as it wasn't used anyway due to the pad not having the correct
pinmux settings.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Marek Vasut <marek.vasut@mailbox.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The sd-vsel-gpios property in the root of the PMIC node is deprecated
and therefore not parsed by the driver anymore. We can safely remove
this as it wasn't used anyway due to the pad not having the correct
pinmux settings.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Marek Vasut <marek.vasut@mailbox.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
There are two ways to set the output voltage of the LD05
regulator. First by writing to the voltage selection registers
and second by toggling the SD_VSEL signal.
Usually board designers connect SD_VSEL to the VSELECT signal
controlled by the USDHC controller, but in some cases the
signal is hardwired to a fixed low level (therefore selecting
3.3V as initial value for allowing to boot from the SD card).
In these cases, the voltage is only determined by the value
of the LDO5CTRL_L register. Introduce a property
nxp,sd-vsel-fixed-low to let the driver know that SD_VSEL
is low and there is no GPIO to actually get that
information from dynamically.
This is equivalent to the following change in Linux:
c8c1ab2c5cb7 ("regulator: pca9450: Handle hardware with fixed SD_VSEL for LDO5")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
For LDO5 we need to be able to check the status of the SD_VSEL input in
order to know which control register is used. Read the status of the
SD_VSEL signal via GPIO and use the correct register accordingly.
To use this, the LDO5 node in the devicetree needs the sd-vsel-gpios
property to reference the GPIO that is used to read back the SD_VSEL
status internally. Please note that the SION bit in the IOMUX must be
set if the signal is muxed as VSELECT and controlled by the USDHC
controller.
This is equivalent to the following change in Linux:
3ce6f4f943dd ("regulator: pca9450: Fix control register for LDO5")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The LDO5 regulator has two configuration registers, but only
LDO5CTRL_L contains the bits for enabling/disabling the regulator.
This is equivalent to the following change in Linux:
f5aab0438ef1 ("regulator: pca9450: Fix enable register for LDO5")
Fixes: 326337fb00 ("pmic: pca9450: Add regulator driver")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This reverts commit 2add051175.
It turns out that all boards using the PCA9450 actually have the
SD_VSEL input connected to the VSELECT signal of the SoCs SD/MMC
interface. Therefore we don't need manual control for this signal
via GPIO and there aren't any users.
This is equivalent to the following change in Linux:
c73be62caabb ("Revert "regulator: pca9450: Add SD_VSEL GPIO for LDO5"")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The code in tps65910_regulator.c treats the field supply in struct
tps65910_regulator_pdata as an int and even tests the value for being
negative so change it from a u32 to int so that the code all works as
expected.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The video test here is specific to the sandbox SDL video driver, so only
build it when that is enabled rather than VIDEO is enabled.
Reported-by: Alison Chaiken <alison@she-devel.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The MediaTek mt6323 power driver cannot build without access to some
platform specific header files. Express that requirements in Kconfig as
well.
Signed-off-by: Tom Rini <trini@konsulko.com>
The commends in include/power/pmic.h say that once SPL_DM_PMIC exists we
should update things. This has been true for some time, so let us update
this to have the legacy portions in their own header, which should not
be directly included. This cleans up the logic within the file too
slightly.
Signed-off-by: Tom Rini <trini@konsulko.com>
In tps65941_buck_val and tps65941_ldo_val hex is an unsigned variable
being assigned the return value from a function that returns int. Change
hex to be an int so that the following test for an error as a negative
value will work as expected.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
In order to get the expected result from
rzg2l_usbphy_regulator_get_enable the return expression needs
parenthesis so that the binary and is performed before the double
logical not.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
In palmas_smps_val and palmas_ldo_val hex is an unsigned variable being
assigned the return value from a function that returns int. Change hex
to be an int so that the following test for an error as a negative value
will work as expected.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
In lp87565_buck_val hex is an unsigned variable being assigned the return
value from a function that returns int. Change hex to be an int so that
the following test for an error as a negative value will work as expected.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
In lp873x_buck_val and lp873x_ldo_val hex is an unsigned variable being
assigned the return value from a function that returns int. Change hex
to be an int so that the following test for an error as a negative value
will work as expected.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
In pmic_reg_read ret is only assigned to inside #if
CONFIG_IS_ENABLED(DM_I2C) so move the test and return ret inside as well
and also guard the declaration of ret with CONFIG_IS_ENABLED(DM_I2C) to
prevent a warning about an unused variable.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
In axp_init after checking the chip ID there is an else clause that
returns ret. ret is guaranteed to be 0 at this point as the code would
have returned above if not. The next statement is a return 0 so the
return ret is redundant, remove it.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
AMD/Xilinx/FPGA changes for v2026.01-rc1
mbv:
- Add it to CI loop
versal2:
- Wire UFS driver
serial:
- Add support for OF_PLATDATA in uartlite
misc:
- Mark some structures as const
u-boot internals were being corrupted following an EFI callback to
get_rng(). One of the many footprints was a corruption of the EFI
protocols linked list.
A request for >16 bytes of random data is broken into smaller requests.
Those requests are fed in a loop to the CAAM RNG, which uses a job
queue ring for interaction.
However, the job queue descriptor is created only at probe time. That
descriptor may end up needing an endian swap (LS1046A) before being fed
to the CAAM RNG. This corrupts the descriptor for the next iteration,
since it will be blindly endian swapped yet again.
Two issues arise. The number of words to endian swap is taken from the
input descriptor itself. So on the second iteration, the length has been
corrupted. This results in a corruption past the end of the descriptor:
whatever is after in memory is endian swapped too. Second, some of the
entries in the descriptor are DMA addresses. If the descriptor is still
somehow considered valid after swapping, the data at the corrupted DMA
address is now trampled.
Linux properly initializes the descriptor for each iteration. This is
what is now done with this commit.
Signed-off-by: Anthony Pighin <anthony.pighin@nokia.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
These values were calculated but not set.
They are required for the calculation of the delays, as stated in the
"QorIQ LS1043A Reference Manual, Rev. 6, 07/2020" page 2172.
The delays are calculated as (1/freq)*PCSSCK*CSSCK and
(1/freq)*PASC*ASC.
Signed-off-by: Tomas Alvarez Vanoli <tomas.alvarez-vanoli@hitachienergy.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In get_lpuart_clk_rate if the call to clk_get_rate returns an error then
the call to return should pass the value of the error which is in rate
rather than ret which will be 0 as its value is not affected by this
error.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Avoid calling free(addr) twice if the device for ucode is not found.
This patch repeats a similar fix but that only applied to code without
CONFIG_TFABOOT enabled. This patch applies to the code with
CONFIG_TFABOOT enabled.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In mc_fixup_dpc_mac_addr noff is assigned the return value from
fdt_add_subnode so that is the variable that should be passed to
fdt_strerror and returned when negative.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In dpni_exit there is a NULL check for dflt_dpni after it is
dereferenced a number of times. Instead move the NULL check to early in
the function. Also assign NULL to dflt_dpni after free in both dpni_init
and dpni_exit.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In dpbp_exit there is a NULL check for dflt_dpbp after it is
dereferenced a number of times. Instead move the NULL check to early in
the function. Also assign NULL to dflt_dpbp after free in both dpbp_init
and dpbp_exit.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In dpio_exit there is a NULL check for dflt_dpio but it happens after
dpio_dflt has been dereferenced a number of times already. Instead move
the NULL check to first thing in the function. Also assign NULL to
dflt_dpio after free in both dpio_init and dpio_exit.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In netc_blk_ctrl_probe the test for failure of the function
clk_prepare_enable should not return PTR_ERR(ipg_clk) as it does not
check IS_ERR(ipg_clk) instead it should return err as that is what is
holding the error code in this case.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In memac_wait_until_free and memac_wait_until_done the use of
post-decrement on the test in the while loop for a timeout means that
timeout will be equal to -1 on exit in that case. Adjust the test for
this expected value.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In fm_eth_bind there is a dereference of dev before it is NULL checked.
Add a NULL check before the first dereference and remove a later NULL
check that is now redundant.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In bmi_rx_port_disable and bmi_tx_port_disable the use of post-decrement
on the test in the while loop for a timeout means that timeout will be
equal to -1 on exit in that case. Adjust the test for this expected
value.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In the case of !zq_en zqcs_init is never assigned to although its value
is used. Correct by initialising zqcs_init to 0.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This commit introduces a new API,
request_firmware_into_buf_via_script(), to the fs_loader framework.
This function allows firmware to be loaded into memory using
a user-defined U-Boot script, providing greater flexibility for
firmware loading scenarios that cannot be handled by static file
paths or device/partition selection alone.
Key features:
- The API runs a specified U-Boot script (by name), which is responsible
for loading the firmware into memory by any means (e.g., load from MMC, USB, network, etc.).
- The script must set two environment variables: 'fw_addr'
(the memory address where the firmware is loaded) and
'fw_size' (the size of the firmware in bytes).
- The function validates these variables, copies the firmware into a newly
allocated buffer (using memdup), and returns the pointer
via the provided double pointer argument.
- The maximum allowed firmware size is checked to prevent buffer overflows.
- The environment variables are cleared after use to avoid stale data.
- Detailed error messages are provided for all failure conditions to aid debugging.
Usage example:
1. Define a U-Boot script in the environment that loads the firmware
and sets the required variables:
=> env set my_fw_script 'load mmc 0:1 ${loadaddr} firmware.bin &&
env set fw_addr ${loadaddr} && env set fw_size ${filesize}'
2. In your code, call the new API:
void *fw_buf = NULL;
int ret = request_firmware_into_buf_via_script(&fw_buf, 0x46000000, "my_fw_script");
if (ret < 0)
return ret;
This approach allows board integrators and users to customize the firmware
loading process without modifying the source code,
simply by changing the script in the U-Boot environment.
Signed-off-by: Lucien.Jheng <lucienzx159@gmail.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[trini: Fix printf of size_t needing to use %zx]
Signed-off-by: Tom Rini <trini@konsulko.com>
