Unlike RK3399, RK3288 the Newer Rockchip SoC's like RK3328 have
different offsets for dsp registers.
Group the dsp register set via dsp_regs pointers so that dsp_offset
would point the dsp_regs to access for any changes in the offset value.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Unlike RK3399, RK3288 the Newer Rockchip SoC's like RK3328 have
different offsets for win registers.
Group the win register set via win_regs pointers so that win_offset
would point the win_regs to access for any changes in the offset value.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Get the regs from priv pointer instead of passing it an argument.
This would simplify the code and better readability.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
HPD detection on some DW HDMI designed SoC's would need to read and
setup the HPD status explicitly.
So, extend the HPD detection code by adding the dw_hdmi_detect_hpd
function and move the default detection code caller there.
The new read and setup hdp will integrate the same function in
later patches.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
DW HDMI support Vendor PHY like Rockchip RK3328 Inno HDMI PHY.
Extend the vendor phy handling by adding platform phy hooks.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
HDP is a hardware connector event, so detect the same once the
controller and attached PHY initialization are done.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Support timing parsing from EDID if panel device tree node
provides DDC i2c bus instead of timings node.
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF201
Tested-by: Agneli <poczt@protonmail.ch> # Toshiba AC100 T20
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
[agust: reworked to fix dm_i2c_* build errors and to big img size]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
MP1:
_ Add OHCI HCD support for STM32MP15xx DHSOM
_ Report OTP-CLOSED instead of rev.? on closed STM32MP15xx
_ Initialize TAMP_SMCR BKP..PROT fields on STM32MP15xx
_ Jump to ep on successful resume in PSCI suspend code
_ Add FASTBOOT support for STM32MP13
_ Fix/Rework key and leds management for STM32MP13/15
_ net: dwc_eth_qos: Clean up STM32 glue code and add STM32MP13xx support
MP2:
_ Add stm32-fmc-ebi support
_ Add: sdmmc2 support and fix AARCH64 compilation
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use led node's name instead for
u-boot,error-led property.
Rename red led node's name to led-red.
Remove status property which is useless.
Add compatible = "gpio-leds"; which is not present in kernel DT.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
red led and button dedicated to fastboot share the same gpio GPIOA13.
Led driver is probed early so the corresponding gpio is taken and
configured in output which forbid fastboot and stm32prog button usage.
To avoid this, remove the "default-state" property from red led node.
This will avoid to trigger the led driver probe() to configure the led
default state during startup.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use led node's name instead for
u-boot,error-led property.
Rename red led node's name to led-red.
Remove status property which is useless.
Add compatible = "gpio-leds" which is not present in kernel DT.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
red led and button dedicated to fastboot share the same gpio GPIOA13.
Led driver is probed early so the corresponding gpio is taken and
configured in output which forbid fastboot and stm32prog button usage.
To avoid this, remove the "default-state" property from red led node.
This will avoid to trigger the led driver probe() to configure the led
default state during startup.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use blue led node's name instead
for u-boot,boot-led property.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use red led node's name instead
for u-boot,error-led property.
Rename red led node's name to led-red.
Remove status property which is useless.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
red led and button dedicated to fastboot share the same gpio GPIOA13.
Led driver is probed early so the corresponding gpio is taken and
configured in output which forbid fastboot and stm32prog button usage.
To avoid this, remove the "default-state" property from red led node.
This will avoid to trigger the led driver probe() to configure the led
default state during startup.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use blue led node's name instead
for u-boot,boot-led property.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use red led node's name instead
for u-boot,error-led property.
Rename "red" led node's name to "led-red".
Remove status property which is useless.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
red led and button dedicated to fastboot share the same gpio GPIOA13.
Led driver is probed early so the corresponding gpio is taken and
configured in output which forbid fastboot and stm32prog button usage.
To avoid this, remove the "default-state" property from red led node.
This will avoid to trigger the led driver probe() to configure the led
default state during startup.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
led-red and button dedicated to fastboot share the same gpio GPIOA13.
led-blue and button dedicated to stm32prog share the same gpio GPIOA14.
Led driver is probed early so the corresponding gpio is taken and
configured in output which forbid fastboot and stm32prog button usage.
To avoid this, remove the "default-state" property from led-red and
led-blue led's node.
This will avoid to trigger the led driver probe() to configure the led
default state during startup.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Instead of using gpio directly to detect key pressed on button
dedicated for fastboot and stm32mprog, make usage of BUTTON UCLASS.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Fix flash@0 partition node name with correct offset.
Fixes: 90f992e6a5 ("arm: dts: stm32: Add partitions in flash0 and nand
node for stm32mp15xx-dhcom/dhcor")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Fix flash@0 partition node name with correct offset.
Fixes: 90f992e6a5 ("arm: dts: stm32: Add partitions in flash0 and nand node for
stm32mp15xx-dhcom/dhcor")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Fix flash@0 and nand@0 partition node name with correct offset.
Fixes: e91d3c6176 ("arm: dts: stm32: Add partitions in flash0 and nand
node for stm32mp15xx-ev1")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
In case of an OTP-CLOSED STM32MP15xx system, the CPU core 1 cannot be
released from endless loop in BootROM only by populating TAMP BKPxR 4
and 5 with magic and branch address and sending SGI0 interrupt from
core 0 to core 1 twice. TAMP_SMCR BKP..PROT fields must be initialized
as well to release the core 1 from endless loop during the second SGI0
handling on core 1. Initialize TAMP_SMCR to protect the first 32 backup
registers, the ones which contain the core 1 magic, branch address and
boot information.
This requirement seems to be undocumented, therefore it was necessary
to trace and analyze the STM32MP15xx BootROM using OpenOCD and objdump.
Ultimately, it turns out that a certain BootROM function reads out the
TAMP_SMCR register and tests whether the BKP..PROT fields are non-zero.
If they are zero, the BootROM code again waits for SGI0 using WFI, else
the execution moves forward until it reaches handoff to the TAMP BKPxR 5
branch address.
This fixes CPU core 1 release using U-Boot PSCI implementation on an
OTP-CLOSED system, i.e. system with fuse 0 bit 6 set.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
SoC revision is only accessible via DBUMCU IDC register,
which requires BSEC.DENABLE DBGSWENABLE bit to be set to
make the register accessible, otherwise an access to the
register triggers bus fault. As BSEC.DBGSWENABLE is zero
in case of an OTP-CLOSED system, do NOT set DBGSWENABLE
bit as this might open a brief window for timing attacks.
Instead, report that this system is OTP-CLOSED and do not
report any SoC revision to avoid confusing users. Use an
SEC/C abbreviation to avoid growing SOC_NAME_SIZE .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The source file is in arch/arm/mach-stm32mp/ecdsa_romapi.c and not
in arch/arm/mach-stm32mp/stm32mp1/ecdsa_romapi.c . There are two
Makefile entries in each subdirectory. Drop the bogus one and keep
only the correct one, the one in arch/arm/mach-stm32mp/Makefile .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
In case the system has resumed successfully, the PSCI suspend resume
code has to jump to the 'ep' successful resume entry point code path,
otherwise the code has to jump to content of the LR register, which
points to failed resume code path.
To implement this distinction, rewrite LR register stored on stack
with 'ep' value in case of a successful resume, which is really in
every case unless some catastrophic failure occurred during suspend.
Without this change, Linux counts every resume as failed in
/sys/power/suspend_stats/fail
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The "st,ext-phyclk" property is a unification of "st,eth-clk-sel"
and "st,eth-ref-clk-sel" properties. All three properties define
ETH CK clock direction, however:
- "st,eth-clk-sel" selects clock direction for GMII/RGMII mode
- "st,eth-ref-clk-sel" selects clock direction for RMII mode
- "st,ext-phyclk" selects clock direction for all RMII/GMII/RGMII modes
The "st,ext-phyclk" is the preferrable property to use.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christophe ROULLIER <christophe.roullier@foss.st.com>
Manage 2 ethernet instances, select which instance to configure with mask
If mask is not present in DT, it is stm32mp15 platform.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Marek Vasut <marex@denx.de> # Rework the code
Reviewed-by: Christophe ROULLIER <christophe.roullier@foss.st.com>
