Add a common board dtsi for use by Milk-V Mars CM and Milk-V Mars CM Lite.
Signed-off-by: E Shattow <e@freeshell.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
[ upstream commit: 651b30c58775e334c79aa3ecd44a3d98ac201db2 ]
(cherry picked from commit 034af14dcd1e6dbfa4f41a340b6d92b054604858)
Relax no-sdio restriction on mmc1 for jh7110 boards. Property was
introduced for StarFive VisionFive2 dts to configure mmc1 for SD Card
but this is not necessary, the restriction is only needed to block use of
commands that would cause a device to malfunction.
Signed-off-by: E Shattow <e@freeshell.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
[ upstream commit: 481ee0fcbb9a0f0706d6d29de9570d1048aff631 ]
(cherry picked from commit b4e73596622f791e3c2a2449022671e4e579fbd0)
The current sifive_clint driver can fully support GHRTv2 clint.
Add the compatible of GHRTv2 clint, sifive,clint2, to sifive_clint_ids
list.
Signed-off-by: Vincent Chen <vincent.chen@sifive.com>
Signed-off-by: Wayling Chen <wayling.chen@sifive.com>
Signed-off-by: Max Hsu <max.hsu@sifive.com>
Signed-off-by: Jimmy Ho <jimmy.ho@sifive.com>
Combining two bits into a mask requires the use of the binary 'or'
operator not the logical one. Correct it.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Svyatoslav Ryhel <clamor95@gmail.com>
The goto immediately after a return is unreachable. Remove it and its
target label as redundant.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Svyatoslav Ryhel <clamor95@gmail.com>
This driver relies on tegra-specific headers to compile so make it
depend on ARCH_TEGRA.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
Bind watchdog driver to the Tegra timer node since it uses one of the
timers to act as a watchdog and has no dedicated hardware block.
Signed-off-by: Lukasz Majewski <lukma@nabladev.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Provide support for Tegra watchdog functionality. The WATCHDOG index 0 in
conjunction with TIMER 5 is used inline with existing Linux kernel driver.
Signed-off-by: Lukasz Majewski <lukma@nabladev.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Remove support for ATAGS-based OS booting. ATAGS are used for booting
older Linux kernel versions and we are moving away from using those.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
This commit introduces a port of the Linux kernel's driver for the
Mediatek's MT7621 I2C controller.
The port was undertaken as the existing driver intended for Mediatek
I2C controllers (mtk_i2c.c) is not compatible with the MT7621.
To use the driver:
1. Ensure that the mode of the i2c pin group is
configured for "i2c" rather than "gpio".
2. Delete the existing (bitbanged) i2c node from
arch/mips/dts/mt7621.dtsi, or specify:
/delete-node/ &i2c;
3. Declare:
i2c: i2c@1e000900 {
compatible = "mediatek,mt7621-i2c";
reg = <0x1e000900 0x100>;
clocks = <&clk50m>;
clock-names = "sys_clock";
resets = <&rstctrl RST_I2C>;
reset-names = "i2c_reset";
pinctrl-names = "default";
pinctrl-0 = <&i2c_pins>;
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
};
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Heiko Schocher <hs@nabladev.com>
No big features this time, mostly a collection of patches that have been
lying around for a bit. There are some DT updates, for those SoCs that
do not use OF_UPSTREAM yet, hopefully that's the last time we need to do
this exercise. And that's offset by switching over two more SoCs to
OF_UPSTREAM. Two new boards get a defconfig, and some improvements for
the sun8i-emac Ethernet driver. Finally a patch that fixes occassional
DRAM size misdetection for new A523 boards.
There are a few outstanding patches that just wait for getting some
details confirmed, which I might send then later.
CI passed, and I tested this briefly on affected boards.
Sync the kernel devicetree source files for the Allwinner SoCs with
32-bit cores that do not use OF_UPSTREAM yet. The files were taken
from a v6.18-rc1 tree.
To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 994e5818392c and 9fdef3c3d8c2.
This commit also adds a new board devicetree for the A33 Vstar board,
plus one DT overlay for the OrangePi Zero interface board.
This update should not impact any existing U-Boot functionality.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Sync the devicetree files from the official Linux kernel tree, v6.18-rc1.
This is covering Allwinner SoCs with 64-bit ARM cores.
The bulk is cosmetic changes: board model name changes, DT node renames,
whitespace fixes.
The actual changes are not dramatic: the CPU cores get their caches
described properly, some A64 video clocks get fixed, some A64 boards
describe the header pins for the WiFi module, the Pinephone adds an
alternative magnetometer used on some board revisions.
On the H5 side the microSD slots get marked as having no write-protect
detection, and the NanoPi Neo Plus2 board describes its regulators better.
The H6 boards switch from RSB to I2C for their PMIC connection.
As before, this omits the non-backwards compatible changes to the R_INTC
controller, to remain compatible with older kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
In contrast to some other Allwinner SoCs, there is no difference between
the DTs for the Allwinner A80 SoCs (sun9i) between the U-Boot and the
Linux kernel repository.
Remove the old copies of the A80 related .dts and .dtsi files, and switch
most of sun9i boards over to use OF_UPSTREAM.
There is the Sunchip CX-A99 (family of) board(s) for which we don't have
a DT in the kernel tree. Keep the .dts file in the legacy U-Boot DT
directory, and let the board's defconfig opt out of OF_UPSTREAM.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
In contrast to some other Allwinner SoCs, there is no difference between
the DTs for the Allwinner T113-s3 SoC (sun20i) between the U-Boot and the
Linux kernel repository.
Remove the old copies of the T113-s3 related .dts and .dtsi files, and
switch the whole SoC (represented by just one board) over to use
OF_UPSTREAM.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
A device-tree property is already defined to indicate that the internal
PHY should be used with active-low leds, which corresponds to a
specific bit in the dedicated syscon register.
Add support for setting this bit when the property is present.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
We know about all the relevant fields in the syscon register so there
is no reason to read it first and modify it.
Build the register from scratch instead, with all relevant fields set.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
NetCube Systems Kumquat is a board based on the Allwinner V3s SoC,
including:
- 64MB DDR2 included in SoC
- 10/100 Mbps Ethernet
- USB-C DRD
- Audio Codec
- Isolated CAN-FD
- ESP32 over SDIO
- 8MB SPI-NOR Flash for bootloader
- I2C EEPROM for MAC addresses
- SDIO Connector for eMMC or SD-Card
- 8x 12/24V IOs, 4x normally open relays
- DS3232 RTC with Battery Backup
- QWIIC connectors for external I2C devices
Signed-off-by: Lukas Schmid <lukas.schmid@netcube.li>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently we pass this for u-boot-spl.kwb targets, however when
building sunxi-spl.bin in the TOC0 format we may also need to
specify a KEYDIR, as such we should also pass this when set
to mkimage for the sunxi-spl.bin target.
Signed-off-by: James Hilliard <james.hilliard1@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
The H6 and H616 DRAM initialisation code recently gained a joint and
improved size detection routine, which helped to avoid the occasional
DRAM size misdetection.
Use the same code for the A523 DRAM initialisation as well, which
suffers from the same misdetection at times.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Chen-Yu Tsai <wens@kernel.org>
The OrangePi 4A is a typical Raspberry Pi model B sized development
board from Xunlong designed around an Allwinner T527 SoC.
The board has the following features:
- Allwinner T527 SoC
- AXP717B + AXP323 PMICs
- Up to 4GB LPDDR4 DRAM
- micro SD slot
- optional eMMC module
- M.2 slot for PCIe 2.0 x1
- 16 MB SPI-NOR flash
- 4x USB 2.0 type-A ports (one can be used in gadget mode)
- 1x Gigabit ethernet w/ Motorcomm PHY (through yet to be supported GMAC200)
- 3.5mm audio jack via internal audio codec
- HDMI 2.0 output
- eDP, MIPI CSI (2-lane and 4-lane) and MIPI DSI (4-lane) connectors
- USB type-C port purely for power
- AP6256 (Broadcom BCM4345) WiFi 5.0 + BT 5.0
- unsoldered headers for ADC and an additional USB 2.0 host port
- 40-pin GPIO header
Add defconfig for it.
Signed-off-by: Chen-Yu Tsai <wens@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Pull request efi-2026-01-rc1-2
CI:
* https://source.denx.de/u-boot/custodians/u-boot-efi/-/pipelines/28024
Documentation:
* develop: virtio: Fix qemu example (true/false -> on/off)
* separate read and write command documentation
* usage: Add general rule for `$?`
* askenv: Reword and remove return value
* seama: Reword return value section
* usage: Use glob for all commands
* Fix typos and formatting
UEFI:
* console: support editable input fields
For clarity, add a reference link to the start of the section on command
documentation that all commands follow some general rules.
Signed-off-by: Tom Rini <trini@konsulko.com>
With the addition of general text about how the return value is handled,
reference that while retaining the additional information about setting
$seama_image_size
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
With the addition of general text about how the return value is handled,
remove the examples from the askenv documentation as they are all normal
expected results.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
For nearly all commands in U-Boot the '?' variable is handled the same
way with 0 meaning success, 1 meaning any failure. Explain this in the
general rules section of the cmdline documentation (with a link to a
counter example) and then remove the redundant wording from most
commands. We retain a section about the return value in a number of
places where we are doing something such as always returning a specific
value or we have useful additional information to go along with the
normal return codes.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Fix the whitespace and add a missing quotation mark
(default = "foo-reva.dtb") in overlay-fdt-boot.rst.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Change the formatting of binman.rst so that the compiled HTML output
becomes more readable. Changes include enumerations and the escaping of
arguments starting with a double dash (e.g. --debug).
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
When editing eficonfig "optional data" (typically cmdline arguments)
it's useful to be able to edit the string rather than having to re-type
the entire thing. Implement support for editing buffers to make this a
whole lot nicer. Specifically, add support for moving the cursor with
the arrow keys and End key as well as deleting backwards with the delete
key.
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
* Avoid two step navigation to get to the description of the write command.
* Add missing index entries
* Correct formatting of the examples.
* Describe configuration and return value.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Peng Fan (OSS) <peng.fan@oss.nxp.com> says:
i.MX95 System Manager(SM) implements Logical Machine Management(LMM) and
CPU protocol to manage Logical Machine(LM) and CPUs(eg, M7).
To manage M7 in a separate LM or in same LM as U-Boot/Linux itself. LMM
APIs and CPU APIs are needed.
When M7 is in LM 'lm-m7', and this LM is managable by 'uboot-lm', U-Boot
could use LMM_BOOT, LMM_SHUTDOWN and etc to manage 'lm-m7'.
If in same LM, use CPU_START, CPU_STOP, CPU_RESET_VECTOR_SET and etc to
manage M7.
Both LMM/CPU APIs will be used by remoteproc driver.
The documentation could be found in Linux Kernel:
drivers/firmware/arm_scmi/vendors/imx/imx95.rst
Link: https://lore.kernel.org/r/20251017-scmi-lmm-v1-0-9fd41e7a5ac0@nxp.com
Add the option to load the bootscript with the tftp command (static IP)
instead of the dhcp command (dynamic IP). For this a new function
tftpb_run similar to dhcp_run, is needed. The selection of which command
to use can be done with the ip_dyn environment variable, which can be
set to yes or no. The ip_dyn variable was chosen as it is already in use
on the imx platforms.
Also edit the bootstd doc.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>
This protocol allows an agent to start, stop a CPU or set reset vector.
It is used to manage auxiliary CPUs in an LM (e.g. additional cores in an
AP cluster).
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Alice Guo <alice.guo@nxp.com>
