The ODROID GO2 devices come with onboard SPI flash, add support for
using the SPI flash.
The BootROM seem to expect the IDBlock at 64 KiB offset compared to the
typical 32 KiB offset from start of SPI flash used by other SoCs.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Include the RK817 PMIC in SPL and enable Kconfig options to power off
the handheld gaming device when it was powered on due to a power cable
plug-in event:
DDR3, 333MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS=1 Die BW=16 Size=1024MB
out
Power Off due to plug-in event
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Include pinctrl nodes and props for sdmmc, sfc and uart in SPL to ensure
pins are configured according to the device tree.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Drop SPL_DRIVERS_MISC, it is not needed/used on these devices.
Enable SPL_FIT_SIGNATURE to ensure the integrity of the FIT images
that are loaded into memory.
Change SPL_MAX_SIZE to 256 KiB, similar to other SoCs where TF-A is
loaded at 0x40000 offset from start of DRAM.
Enable SPL_DM_SEQ_ALIAS to ensure device aliases are applied in SPL.
Drop use of SPL_TINY_MEMSET, there is plenty room for the normal memset.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The handheld gaming devices that this defconfig tagets does not contain
an Ethernet port, remove Ethernet related Kconfig options.
They also do not contain any pwm-regulator in their DTs, remove the
PWM regulator related Kconfig option.
Display/video is not supported in U-Boot, remove all display/video
related Kconfig options.
There is no real functional change expected with these options removed.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a new common rk3326-u-boot.dtsi and move the SoC common overrides
into it.
This should not contain any changes other than a possible reorder of
nodes and props.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
GPIO devices are needed in U-Boot proper phase, sdmmc and sfc devices
are needed in SPL and pre-reloc phase.
Update bootph- props to match what boot phase devices are needed at.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
DTs from dts/upstream already contain aliases for i2c, mmc and serial.
Remove the aliases and status=okay that are already defined in upstream
board or SoC DT.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The alias spi0 is incorrectly being re-defined in board u-boot.dtsi to
the SPI flash controller instead of the actual spi0 controller.
SPI flash support is currently not working on odroid-go2 due to missing
Kconfig options and other required device tree changes.
Remove the re-defined alias for spi0 to allow use of the real spi0,
proper SPI flash support is introduced in a later patch.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add dummy implementation of set_rate for SCLK_GPU and SCLK_WIFI_PMU to
allow use of dts/upstream assigned-clocks in cru and pmucru nodes.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A variety of Qualcomm features/fixes for this cycle, notably with a few
new platforms gaining support:
* Initial support for SDM670 (similar to SDM845), SM6350, and SM7150
platforms is added
* USB and UART issues on MSM8916 are addressed (improving stability/
reliability)
* Firmware loading is implemented for the GENI serial engine, this is
used on some platforms to load firmware for i2c/spi/uart to work
Some additional patches like binman support for building MBN files still
need some additional work.
CI: 8ef6ac07b3/pipelines
Enable the serial engine clk in probe so that this driver can work on
platforms that don't already initialize the clk for this device before
this driver runs. This fixes a problem I see on Coreboot platforms like
Trogdor where the UART hardware isn't enabled by coreboot unless the
serial console build is used.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://patch.msgid.link/20250714-geni-load-fw-v5-6-5abbc0d29838@linaro.org
Signed-off-by: Casey Connolly <kcxt@postmarketos.org>
Qualcomm peripherals like UART, SPI, I2C, etc are all exposed under a
common GENI Serial Engine wrapper device. Replace the stub driver we use
for this currently with a full-on misc device and implement support for
loading peripheral firmware.
Each of the peripherals has it's own protocol-specific firmware, this is
stored on the internal storage of the device with a well-known partition
type GUID.
To support this, GENI will bind peripherals in two stages. First the
ones that already have firmware loaded (such as the serial port) are
bound in the typical way. But devices that require firmware loading are
deferred until EVT_LAST_STAGE_INIT. At this point we can be sure that
the storage device is available, so we load the firmware and then bind
and probe the remaining children.
Child devices are expected to determine if firmware loading is necessary
and call qcom_geni_load_firmware().
Since Linux currently doesn't support loading firmware (and firmware may
not be available), we probe all GENI peripherals to ensure that they
always load firmware if necessary.
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
Link: https://patch.msgid.link/20250714-geni-load-fw-v5-3-5abbc0d29838@linaro.org
Signed-off-by: Casey Connolly <kcxt@postmarketos.org>
The change in commit c1af358cf5 ("imx: mx6ull: fix REFTOP_VBGADJ
setting") is not correct. According to latest i.MX6ULL fuse table,
the REFTOP_TRIM[2:0] fuse is defined as below. So the previous codes
are correct, only need to fix the comments.
Set the REFTOP_VBGADJ field in PMU_MISC0 register based on the
REFTOP_TRIM fuse:
'000" - set REFTOP_VBGADJ[2:0] to 3'b000
'001" - set REFTOP_VBGADJ[2:0] to 3'b001
'010" - set REFTOP_VBGADJ[2:0] to 3'b010
'011" - set REFTOP_VBGADJ[2:0] to 3'b011
'100" - set REFTOP_VBGADJ[2:0] to 3'b100
'101" - set REFTOP_VBGADJ[2:0] to 3'b101
'110" - set REFTOP_VBGADJ[2:0] to 3'b110
'111" - set REFTOP_VBGADJ[2:0] to 3'b111
Sven Schwermer reported:
"These are the symptoms: Very few of the thousands of devices that we
manufacture (< 1%) fail to decompress a large XZ archive once in Linux
userspace. We have not found any form of memory testing or other load
that reproduces this issue. Reverting the offending patch fixes this
behavior on the affected devices."
Revert the offending commit to fix the regression.
Reported-by: Sven Schwermer <u-boot@schwermer.no>
Signed-off-by: Ye Li <ye.li@nxp.com>
[fabio: Fixed checkpatch warning and added Sven's report]
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Commit 2a7acc865b ("configs: colibri-imx8x: enable RNG support for KASLR")
enables FSL_CAAM which requires initialization in arch_misc_init().
The ARCH_MISC_INIT configuration was added to the relevant defconfig.
Commit d0ed963690 ("global: Make ARCH_MISC_INIT a selected symbol")
changed ARCH_MISC_INIT to require explicit selection by the developer.
With this change the colibri-imx8x defconfig is no longer sufficient to
enable ARCH_MISC_INIT when FSL_CAAM is selected.
Add the necessary selection to automatically enable ARCH_MISC_INIT when
FSL_CAAM is enabled on i.MX8 platforms.
Fixes: d0ed963690 ("global: Make ARCH_MISC_INIT a selected symbol")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This board is very tight on space in SPL; in fact with my compiler it
ends up just exactly on the wrong side:
spl/u-boot-spl.bin exceeds file size limit:
limit: 0xa000 bytes
actual: 0xa014 bytes
excess: 0x14 bytes
The repeated "lookup and request" pattern in spl_board_init() suggests
a low-hanging fruit for reducing the code size. This reduces the
object size of spl/board/liebherr/btt/btt.o by 300 bytes.
I've left the lack of error handling as-is; there isn't really
anything to do if it fails, so I suppose the printfs are the best that
can be done.
Signed-off-by: Rasmus Villemoes <ravi@prevas.dk>
NXP i.MX SoCs are available in different temperature grades. By default,
device-tree contains only thermal trips for consumer grade parts. On the
other hand, part temp grade fuse can be used to determine thermal trip
points. We already do this in imx_tmu_bind() function. Now, factor out
this functionality to a standalone function imx_tmu_set_trips() and use
it for both cases. This fixes an issue where 'cpu-thermal' child device
would set different thermal trips than the parent 'tmu@44482000' sensor,
depending on which gets used.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
The memory size of the 0098 SKU is 8 GB instead of 16 GB.
Fix PID4 0098 Aquila iMX95 definition.
Fixes: 4c93407165 ("toradex: tdx-cfg-block: add new pid4 support")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
CI: https://source.denx.de/u-boot/custodians/u-boot-mmc/-/pipelines/28083
- Add support for Samsung Exynos 7870 DW-MMC device
- Add support for Samsung S2MPU05 PMIC device
- Add compatible string for Exynos5250 in Exynos DW-MMC driver
- Add support for handling UHS-I voltage signaling without power-cycle
- Minor misc cleanup
Guard execute_tuning with MMC_SUPPORTS_TUNING, otherwise there will be
build failure:
drivers/mmc/exynos_dw_mmc.c:484:10: error: 'struct dm_mmc_ops' has no member
named 'execute_tuning'
.execute_tuning = exynos_dwmmc_execute_tuning,
^~~~~~~~~~~~~~
Cc: Kaustabh Chakraborty <kauschluss@disroot.org>
Acked-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reorder the SDHCI_INT_SPACE_AVAIL and SDHCI_INT_DATA_AVAIL flags in the
SDHCI_INT_DATA_MASK definition to match the bit order as defined in the
SDHCI specification and maintain consistency with the register layout.
The functional behavior remains unchanged as this only affects the
order of OR operations in the mask definition.
Signed-off-by: Tanmay Kathpalia <tanmay.kathpalia@altera.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Some boards have SD card connectors where the power rail cannot be switched
off by the driver. However there are various circumstances when a card
might be re-initialized, such as after system resume, warm re-boot, or
error handling. However, a UHS card will continue to use 1.8V signaling
unless it is power cycled.
If the card has not been power cycled, it may still be using 1.8V
signaling. According to the SD spec., the Bus Speed Mode (function group 1)
bits 2 to 4 are zero if the card is initialized at 3.3V signal level. Thus
they can be used to determine if the card has already switched to 1.8V
signaling. Detect that situation and try to initialize a UHS-I (1.8V)
transfer mode.
Signed-off-by: Tanmay Kathpalia <tanmay.kathpalia@altera.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Samsung S2MPU05 PMIC is used in devices with the Exynos7870 SoC, it
houses voltage regulators and an RTC module. Add support for this device
variant in the driver, which also binds the corresponding voltage
regulator driver.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Samsung's S2MPU05 PMIC is used by Exynos7870 SoC. It has 5 buck and 38
LDO regulators. Add support for this device variant in the driver.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The functions s2mps11_{buck,ldo}_mode use the s2mps11_{buck,ldo}_modes
arrays directly in order to extract the mode of a certain register.
This approach does not allow similar devices of other variants (which
may support a different set of modes) to work with the same driver.
Instead of using these arrays hardcoded, extract them from the device's
uclass platform data. Now the responsibility of setting these arrays
properly is done by functions s2mps11_{buck,ldo}_probe, by implementing
a switch-case block which can support modes of multiple variants if and
when added.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In the Linux kernel driver, all information related to LDO and BUCK
regulators are stored in descriptive arrays. This also allows multiple
variants to be supported by the same driver.
Define a struct sec_regulator_desc which holds all values required by a
regulator. Create an array of said struct containing all regulators. The
descriptors are designed to follow a style similar to what's seen in the
Linux driver, so comparing one with the other is simple.
In functions such as s2mps11_{buck,ldo}_{val,mode} these values are to
be used, make necessary modifications to pull them from the descriptors.
Since multiple variants have varying descriptors, select them from
within a switch-case block.
Functions s2mps11_{buck,ldo}_{volt2hex,hex2volt} and arrays
s2mps11_buck_{ctrl,out} are phased out as the calculations are now
hardcoded in descriptors, thusly, it reduces clutter and enhances
readability.
Two macros in s2mps11.h, S2MPS11_LDO_NUM and S2MPS11_BUCK_NUM are
removed as they are no longer being used.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
There are multiple PMICs by Samsung which are similar in architecture
(register layout, interface, etc.) and is possible to be driven by a
single driver. Variant specific code and data should be managed properly
in the driver.
And an enum which describes all supported variants. Pass the enum as the
device driver data. Introduce a switch-case block on the enum for any
variant specific code.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
