The existing approach does not account for interleaving in the DDRs when
setting up regions. There is support for MSMC to calculate the regions
for each DDR, so modify k3_ddrss_probe to set the regions accordingly
for multi-DDR systems.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Add support for calculation of the protected regions for each DDR in
multi-DDR systems. Since MSMC is the parent node of the individual DDRs
as well as responsible for their interleaving, it only makes sense for
MSMC to contain the logic for dividing the regions.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
In K3 multi-DDR systems, the MSMC is responsible for the interleave
mechanism across all the DDR controllers. Add support for MSMC to obtain
the number of controllers it's responsible for using the DT.
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
As we increase the functionalities that the K3 DDRSS sub-system support,
it is becoming more evident that the same logic cannot apply to both
single as well as multiple DDR controller devices. Add
CONFIG_K3_MULTI_DDR to be used to differentiate between the two.
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Instead of defaulting to choosing the entire DDR region when enabling
inline ECC, allow picking of a range within the DDR space using DT to
enable.
It expects such a node within the memory node, in the absence of which
we resort to enabling inline ECC for the entire DDR region:
inline_ecc: protected@9e780000 {
device_type = "ecc";
reg = <0x9e780000 0x0080000>;
bootph-all;
};
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
The reserved space needed for storing the parity remains the same no
matter the size of the region that is being protected. Add this as a
comment for better code understanding.
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
To prevent checkpatch warning once we start using this macro more
frequently, shorten the length of it. While at it, also move the
structure k3_ddrss_ecc_region above k3_msmc so that future patches can
have it as a member of k3_msmc.
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Let ecc_regions[x].start reflect the start of the ECC region in terms of
DDR addressing rather than system addressing. This will make it easier
to extend the usage of the same ecc_regions structure for multi-DDR
systems as well.
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
In k3_nav_ringacc_probe_dt there can be no error code returned from
dev_read_u32_default so ret is not assigned to and should not be used.
Remove the use of ret from the dev_err call as it is unitialised.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Move the first dereference of ring to after the NULL check has occurred.
This will prevent any possible dereference of NULL.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In k3_r5f_split_reset and k3_r5f_unprepare ret may not have been
assigned to before the code reaches the return ret at the function exit.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In the struct ti_sci_proc the fields proc_id and host_id are declared as
u8 so cannot be set to nor compared with a macro defined with a value
using 16 bits. Change the macro to only use 8 bits to make the code work
as expected.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In rt5677_bic_or the call to rt5677_i2c_read returns an int so old
should also be an int to receive that value and then be able to test it
for being negative which would indicate an error.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In s5pxx18_pinctrl_set_state testing count to be negative will always
fail as count is unsigned despite receiving the return value of a
function that returns an int. Change count and idx to be of type int to
allow the test to work as expected and remove the need for any implicit
casts. Also change pin to be u32 which is what all called functions
expect.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
If there is an unhandled KCS/BPC pending interrupt after reboot,
the KCS/BPC Linux driver may trigger interrupts immediately upon
registering the irq. However, since the driver is not yet initialized
to handle them, this can lead to unexpected behavior.
To prevent this, disable KCS/BPC interrupts in u-boot to avoid pending
interrupts from being raised before the Linux driver is fully initialized.
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Enabling an eSPI channel(e.g. Peripheral Channel) during
an eSPI transaction might cause the BMC eSPI module to
transition to a wrong state and therefore respond with
FATAL_ERROR on incoming transaction.
Add workaround to avoid the module getting into the wrong
state.
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
When doing a dm_i2c_read followed by a dm_i2c_write, the subsequent
transaction may get npcm_i2c_check_sda error because the module is
still busy in STOP condition in previous dm_i2c_read.
Always check and wait for module to be out of busy before starting
an i2c transaction.
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
In stmfx_read_reg there is duplicated code to detect ret < 0 and return
ret if so. Remove one version of it.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In single_read there is a switch block with a default label. All cases
in the switch block, including the default, return directly. So any code
following the switch block is unreachable. Remove the unreachable code.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
The test for the interrupt LPDDR4_INTR_BIST_DONE is using a bitwise and
but the test is simple logic so use the more appropriate logical and.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In j721e_wiz_probe the test for too many lanes jumps to the error exit
path without assigning an error code which could lead to calling code
silently ignoring the failure. Set the error code.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In keystone_usb_init the return code from psc_enable_module should be
returned as is rather than being negated.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
A few timer drivers cannot build without access to some platform
specific header files. Express those requirements in Kconfig as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
port_id is an unsigned variable so cannot be negative. Remove the test
checking for port_id being less than 0.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In am65_cpsw_phy_init it is not certain that ret will be assigned to
before it reaches the 'return ret' statement. Initialise ret to ensure
that ret is valid.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In cs4340_upload_firmware a buffer is allocated with malloc but this is
never freed. The pointer to this buffer, addr, is not even kept
unchanged. But in some cases addr is not a buffer allocated by malloc.
Introduce the use of another pointer to keep track of the buffer and to
know if it needs to be freed.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
A few ram drivers cannot build without access to some platform
specific header files. Express those requirements in Kconfig as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
A few serial drivers cannot build without access to some platform
specific header files. Express those requirements in Kconfig as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
When calling writel we do not have a return value to check or pass
along. This function should therefore be void and not return what writel
gives us.
Signed-off-by: Tom Rini <trini@konsulko.com>
This driver makes calls to in8/out8(). On PowerPC these are separate and
real calls but elsewhere they are able to simply be wrappers to
inb/outb. Rework this logic to be able to build this driver on more
platforms.
Signed-off-by: Tom Rini <trini@konsulko.com>
The Marvell RTC rtc driver cannot build without access to some
platform specific header files. Express that requirements in Kconfig as
well.
Signed-off-by: Tom Rini <trini@konsulko.com>
The MPC83xx sysreset driver cannot build without access to some
architecture specific header files. Express that requirements in Kconfig
as well.
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
A few sound drivers cannot build without access to some platform
specific header files. Express those requirements in Kconfig as well.
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The Qualcomm Snapdragon "SoC" driver cannot build without access to some
ARM64 specific functionality. Express that requirements in Kconfig as
well.
Reviewed-by: Casey Connolly <casey.connolly@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The TI IPU remoteproc driver cannot build without access to some
platform specific header files. Express that requirements in Kconfig as
well.
Signed-off-by: Tom Rini <trini@konsulko.com>
A few reset drivers cannot build without access to some platform
specific header files. Express those requirements in Kconfig as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
This driver references the logarithmic macros while relying on an
indirection inclusion of <linux/log2.h>. Add the missing include
directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
A few pwm drivers cannot build without access to some platform
specific header files. Express those requirements in Kconfig as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
A few pinctrl drivers cannot build without access to some platform
specific header files. Express those requirements in Kconfig as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
The symbol "SM" is a library symbol and should not be prompted for. It
should be selected by the drivers that use it. In this case we need to
add a SANDBOX_SM symbol for the sandbox driver. The meson SM driver
cannot build on other platforms, so add the appropriate dependency.
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
In do_e1000_spi_checksum a temporary buffer is allocated but never
freed. Add code to free on exit. Also refactor the code to make the exit
code common.
This issue found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
The Linux pinctrl-sx150 was originally written as a GPIO driver
and fully rewritten by me as a Pinctrl driver and extended by
other contributors.
Fixup the Copyright header style and correctly report the
Copyright headers from the Linux driver.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
In gpio_dwapb_bind plat is used to reference memory allocated by
devm_kcalloc but it is attempted to be freed using kfree. Instead free
this memory using the correct devm_kfree function.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Acked-by: Quentin Schulz <quentin.schulz@cherry.de>
The function dev_read_u32_default does not return an error and the
variable 'val' is unsigned so testing for >= 0 will always be true. It
looks like the code was attempting to return -1 if xtal-load-pf was not
present but that cannot work. Instead use dev_read_u32 which returns an
error code separately from writing the value into the passed pointer.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Fixes: 260777fc23 ("clk: cdce9xx: add support for cdce9xx clock synthesizer")
Acked-by: Quentin Schulz <quentin.schulz@cherry.de>
This adds more common functions found on other architectures that will
allow for more compile-testing of drivers. These are either dummy
functions as we do not need them or mappings to existing functions,
similar to how other architectures handle it.
Signed-off-by: Tom Rini <trini@konsulko.com>
