SOC can boot in the device which is not accessible from APU and running
this is detected as error which ends up in stopping boot process.
Boot mode detection and logic around is present to setup priority on boot
devices that SOC boot device is likely also used for booting OS.
Change logic to detect this case with showing message about it but don't fail
in boot process and don't prioritize boot device in this case.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20230904032035.11926-4-venkatesh.abbarapu@amd.com
SOC can boot in the device which is not accessible from APU and running
this is detected as error which ends up in stopping boot process.
Boot mode detection and logic around is present to setup priority on boot
devices that SOC boot device is likely also used for booting OS.
Change logic to detect this case with showing message about it but don't fail
in boot process and don't prioritize boot device in this case.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20230904032035.11926-3-venkatesh.abbarapu@amd.com
SOC can boot in the device which is not accessible from APU and running
this is detected as error which ends up in stopping boot process.
Boot mode detection and logic around is present to setup priority
on boot devices that SOC boot device is likely also used for booting OS.
Change logic to detect this case with showing message about it but don't
fail in boot process and don't prioritize boot device in this case.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20230904032035.11926-2-venkatesh.abbarapu@amd.com
Location of bootscript in flash can be specified via /options/u-boot DT
node by using bootscr-flash-offset and bootscr-flash-size properties.
Values should be saved to script_offset_f and script_size_f variables.
Variables are described in doc/develop/bootstd.rst as:
script_offset_f
SPI flash offset from which to load the U-Boot script, e.g. 0xffe000
script_size_f
Size of the script to load, e.g. 0x2000
Both of them are used by sf_get_bootflow() in drivers/mtd/spi/sf_bootdev.c
to identify bootscript location inside flash.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/60a84405f3fefabb8b48a4e1ce84431483a729f3.1693465465.git.michal.simek@amd.com
ofnode_read_bootscript_flash() reads bootscript address from
/options/u-boot DT node. bootscr-flash-offset and bootscr-flash-size
properties are read and values are filled. When bootscr-flash-size is not
defined, bootscr-flash-offset property is unusable that's why cleaned.
Both of these properties should be defined to function properly.
Also add test to cover this new function.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/08a3e6c09cce13287c69ad370e409e7f1766b406.1693465465.git.michal.simek@amd.com
Now that the zynqmp pinctrl driver supports the tri-state registers, make
sure that the pins requiring output-enable are configured appropriately for
SOMs.
Without it, all tristate setting for MIOs, which are not related to SOM
itself, are using default configuration which is not correct setting.
It means SDs, USBs, ethernet, etc. are not working properly.
In past it was fixed through calling tristate configuration via bootcmd:
usb_init=mw 0xFF180208 2020
kv260_gem3=mw 0xFF18020C 0xFC0 && gpio toggle gpio@ff0a000038 && \
gpio toggle gpio@ff0a000038
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/7ecd98b2a302c5c6628e0234482f23c38e721fd6.1693492064.git.michal.simek@amd.com
The bootscript is expected at a default address specific to each
platform.
When high speed memory like Programmable Logic Double Data Rate RAM
(PL DDR RAM) or Higher Bandwidth Memory RAM (HBM) is used the boot.scr
may be loaded at a different offset. The offset needs to be set through
setenv. Due to the default values in some cases the boot.scr is falling
in between the kernel partition.
The bootscript address or the bootscript offset is fetched directly from
the DT and updated in the environment making it easier for automated
flows.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/fac7020b31e1f150b021d666f0d588579ea671ad.1693465140.git.michal.simek@amd.com
Kernel Address Space Layout Randomization (KASLR) is a hardening
feature that aims to make it more difficult to take advantage
of known exploits in the kernel, by placing kernel data
structures at a random address at each boot.The bootloader
supports randomizing the virtual address at which the kernel image
is loaded. The bootloader must provide entropy by passing a random
u64 value in the /chosen/kaslr-seed device tree node.
When we run "kaslrseed" command from U-Boot, the bootloader will
genarate the kaslr-seed and update the /chosen/kaslr-seed DT property.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230831031658.2203-4-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Kernel Address Space Layout Randomization (KASLR) is a hardening
feature that aims to make it more difficult to take advantage
of known exploits in the kernel, by placing kernel data structures
at a random address at each boot.The bootloader supports randomizing
the virtual address at which the kernel image is loaded.
The bootloader must provide entropy by passing a random u64 value
in the /chosen/kaslr-seed device tree node.
When we run "kaslrseed" command from U-Boot, the bootloader will
genarate the kaslr-seed and update the /chosen/kaslr-seed DT property.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230831032612.2729-4-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
This fixes below build error when CC_OPTIMIZE_FOR_DEBUG is enabled and
CONFIG_FPGA or CONFIG_SPL_FPGA are not enabled.
When CC_OPTIMIZE_FOR_DEBUG is enabled, unused code will not be optimized
out. Hence, fpga_load function must have a dummy implementation to avoid
the build error.
../common/spl/spl_fit.c:591: undefined reference to `fpga_load'
collect2: error: ld returned 1 exit status
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20230831075247.137501-1-chanho61.park@samsung.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
All si570 mgt chips have factory default 156.25MHz but DT changed it to
148.5MHz. After tracking it is pretty much c&p fault taken from Zynq
zc702/zc706 boards where 148.5MHz was setup as default because it was
requirement for AD7511 chip available on these boards.
ZynqMP board don't contain this chip that's why factory default frequency
can be used.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/c052ddf39e392e97f87f1c57ea06f3508733c672.1692947486.git.michal.simek@amd.com
Kernel Address Space Layout Randomization (KASLR) is a hardening
feature that aims to make it more difficult to take advantage
of known exploits in the kernel, by placing kernel data structures
at a random address at each boot.The bootloader supports randomizing
the virtual address at which the kernel image is loaded.
The bootloader must provide entropy by passing a random u64 value
in the /chosen/kaslr-seed device tree node.
When we run "kaslrseed" command from U-Boot, the bootloader will
genarate the kaslr-seed and update the /chosen/kaslr-seed DT property.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230824032712.13399-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
HBM stands for high bandwidth memory and is a type of memory interface used
in 3D-stacked DRAM (dynamic random access memory) in some AMD GPUs (aka
graphics cards), as well as the server, high-performance computing (HPC)
and networking and client space. High Bandwidth Memory(HBM) has total 16
channels, one channel is divided into two pseudo channels which makes its
32 banks each with some amount of memory.
And then we have DDR_LOW PS low, DDR_HIGH0 PS high, DDR_HIGH1 PS very high
and pretty much there should be also place for PL DDR. So maximum number of
memory banks will be 36, updating the CONFIG_NR_DRAM_BANKS to 36.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/ed9eaf5c20501ee691d7d28a173511cd9a87f161.1690958095.git.michal.simek@amd.com
This is not needed, so drop it. Also use a capital 'O' for the option,
while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
We need CONFIG_OF_LIBFDT to be able to do fdt fixups, so add that
condition.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Standard boot has been in place for a while now. Quite a few problems
have been found and fixed. It seems like a good time to mark the
script-based approach as deprecated and encourage people to use standard
boot.
Update the DISTRO_DEFAULTS Kconfig to encourage people to move to
standard boot, which is able to boot Linux distributions automatically.
Add a short migration guide to make this easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These don't relate to booting. Move them out of there and into the same
place as the other related settings.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This option already depends on FIT, so put it under the same umbrella, so
that it appears in the FIT menu.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
All boards which actually define this address enable SPL_LOAD_FIT, or at
least just rely on the default value of 0. So drop the dependency.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This CONFIG is used but is not given a value by some boards. Use
a default value of 0 explicitly, rather than relying on the 0 value
provided by CONFIG_SPL_LOAD_FIT_ADDRESS
This will allow us to make SPL_LOAD_FIT_ADDRESS depend on SPL_LOAD_FIT
as it should.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is a major feature with a lot of options. Give it its own menu to
tidy up the 'make menuconfig' display. Drop the 'depends on FIT' pieces
which are now unnecessary, since they are now bracketed by an 'if FIT'.
Leave CONFIG_TIMESTAMP out since it affects legacy images too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Phrases like 'Enable support for' are pointless since this is an option
which enables things. Drop that part so it is easier to follow.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move more options relating to fixing up a device tree into the new
devicetree-fixup menu.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This relates to booting, so move it there. Create a new Kconfig menu for
things related to devicetree fixup.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This relates to booting since it fixes up the devicetree for the OS. Move
it into the boot/ directory.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Rename Unit tests to Testing, since it is a stretch to describe some of
the tests as unit tests. Move POST there as well, so it doesn't show up
by itself in the top-level menu.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These appear prominently in the main menu at present. Move them to the
video Kconfig where they belong.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This relates to graphics which is only active when CONFIG_VIDEO is
enabled. Move it into that directory.
For most boards there is no harm in compiling it always, since it if not
used it will be dropped by the linker. But for the EFI app this is not
the case, so retain use of the BMP Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is perhaps not a commonly used feature so should not have its own
option in the main menu. Move it under general setup.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These should not be part of the 'system tables' menu. Move them outside
on their own.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 7d0f3fbb93 ("lib: rational: copy the rational fraction lib...")
Reviewed-by: Tom Rini <trini@konsulko.com>
