Checkpatch warns that it's generally not useful to have
the filename in the file. The warning is valid, drop the
encoded file name. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add initial pin control tables for the Renesas R-Car X5H R8A78000 SoC.
This SoC is the first one which includes custom DRV register handling,
different from previous generations due to change in DRV register bit
layout.
Signed-off-by: Huy Bui <huy.bui.wm@renesas.com>
Signed-off-by: Khanh Le <khanh.le.xr@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The upcoming Renesas R-Car Gen5 uses different mapping of bits in DRV
control register, which is incompatible with existing DRV register bit
mapping. Add .set_drive_strength callback into sh_pfc_soc_operations
and call it from sh_pfc_pinconf_set(), to allow each SoC specific PFC
driver to implement replacement .set_drive_strength. Make the current
sh_pfc_pinconf_set_drive_strength() non-static, rename it with rcar_
prefix, and pass it as .set_drive_strength for existing PFC drivers.
This is a preparatory patch for R-Car Gen5, no functional change.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Consistently use .set_drive_strength() and pass exisiting
sh_pfc_pinconf_set_drive_strength() as its parameter for
all PFC drivers. Rewrite commit message.]
Show bit position in config write debug log, which is helpful for cases
where the p port setting is applied at the exact p bit position.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Unsplit the string
Fix Kconfig entry indent to be always consistently indented with
leading tabs, never with leading spaces. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add support for the GPIO controller block in the R-Car Gen5 SoC family.
The GPIO controller has a General Input Enable Register (INEN), whose
reset state is to have all input disabled. The GPIO controller also has
updated offsets for its control registers. U-Boot uses three registers,
INDT, POSNEG, INEN, which have updated offsets, those are handled by the
driver.
Signed-off-by: Huy Bui <huy.bui.wm@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: - Access Gen5 specific registers via driver data offsets,
- Update commit message]
The Renesas R-Car Gen5 GPIO controller has INDT, POSNEG, INEN registers
at different offsets compared to previous generations. Introduce three
new entries in struct rcar_gpio_data {} match data to describe these
register offsets for each GPIO controller. Update the driver to access
these three registers through the match data offsets. No functional
change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Wrap the RCAR_GPIO_HAS_INEN quirk in more flexible struct rcar_gpio_data {}
in preparation for addition of Renesas R-Car Gen5 GPIO controller support.
The Renesas R-Car Gen5 GPIO controller requires more than a single quirk
to properly describe it, therefore increase the flexibility and introduce
full match data structure, and use it throughout the driver. No functional
change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Remove register macros for registers which are not used by this driver.
This makes it easier to get an overview of which registers are really
used by the driver. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The PFC offset is no longer used directly in the driver since commit
fbf26bea39 ("gpio: renesas: Migrate to pinctrl GPIO accessors")
Drop the pfc_offset parsing.
Fixes: fbf26bea39 ("gpio: renesas: Migrate to pinctrl GPIO accessors")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add PHY driver for Multi-Protocol PHY present on Renesas R-Car X5H
R8A78000 SoC. Currently, the PHY driver only supports configuring
the MPPHY for ethernet operation.
Signed-off-by: Thanh Quan <thanh.quan.xn@renesas.com>
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> #Fix License-Identifier
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Clean up macros, indent, clock and reset handling in probe,
rename the driver and add r8a78000- into compatible string,
update commit message.]
Add support for the Ethernet Physical Coding Sublayer (PCS) controller
on R-Car Gen5 SoCs, specifically the Renesas R-Car X5H R8A78000.
The controller is based on the SERDES infrastructure used in previous
R-Car generations, with updates for Gen5 register layout and features.
Because majority of this driver is SoC-specific register programming,
the majority of this driver is different enough from R8A779F0 SerDes
driver to justify its own driver. Deduplication of the remaining bits
of code does not yield any improvement.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Thanh Quan <thanh.quan.xn@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Add missing clk_bulk_disable() in fail path.
Drop always-true aneg_on setting.
Reduce poll delay from 100s to 100ms.
Use bulk reset operations to finalize reset handling.]
Add support for the Renesas Ethernet Switch3 (RSW3) controller,
present in R-Car Gen5 SoCs such as R-Car X5H (R8A78000). The
hardware offset differences are handled via driver match data.
The driver newly detects whether the switch prot is connected
to xPCS or not, and if so, turns on MIOC bit 3. This is new on
R-Car X5H. GWCKSC register is also programmed only on X5H. The
rest of the operation is identical to RSwitch2.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
Signed-off-by: Thanh Quan <thanh.quan.xn@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
The MPIC_MDC_CLK clock setting value differs between R-Car S4
and R-Car X5H. Parametrize the value in preparation for R-Car
X5H addition into this driver. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The GWDCBAC0, GWDCBAC1, FWPBFCSDC, CABPIRM register offsets changed
between R-Car S4 and R-Car X5H. Parametrize their offsets in preparation
for R-Car X5H addition into this driver. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Inline FWRO, CARO, GWRO, TARO, RMRO macros directly into the
follow up register macros. FWRO, CARO, GWRO, TARO are already
zero, drop them. RMRO is 0x1000, increment all registers which
add RMRO by 0x1000 directly. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The forwarding engine CSD register offset changed between the
R-Car S4 and R-Car X5H. Parametrize this offset in preparation
for R-Car X5H addition into this driver. Clean up the macro
parameter names and make them more obvious. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The total port counts differ across variants of this IP in
R-Car S4 and R-Car X5H. Parametrize port count in preparation
for R-Car X5H addition into this driver. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The COMA, ETHA, GWCA offsets differ across variants of this IP in
R-Car S4 and R-Car X5H. Parametrize these offsets in preparation
for R-Car X5H addition into this driver. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This IP does support operating MII and SerDes via different ports.
Currently, the driver assumes that MII and SerDes are always bound
together on the same port, but this may not be the case. Implement
support for controlling MII and SerDes separately.
While the change is extensive, the gist of the change is to pass
pointer to the selected port registers to MII or SerDes functions,
depending on which port and operations should be done on that port.
Each combined ETHA instance contains both MII and SerDes register
pointers, which may not point to the same port, and passes those
registers to MII and SerDes functions respectively to control the
MII or SerDes of each port.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The new version of RSwitch3 in Renesas R-Car Gen5 uses multiple
clock to supply the IP. Convert the driver to bulk clock API to
cater for both single clock of R-Car S4 and multiple clock of
R-Car Gen5. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Empty RX DMA descriptor must contain .die_dt field set to DT_FEMPTY,
because hardware DMA overwrites this field to non-DT_FEMPTY when data
are received, and the .recv callback tests the content of RX descriptor
.die_dt field to determine whether hardware did receive any data and
updated the .die_dt field, and based on that information, receives a
packet or not. Fix the incorrect RX DMA descriptor initialization to
assure the .recv callback always works correctly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Fix indent from multiple spaces to tabs, to be consistent with
coding style and the rest of the driver. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
When spl boot device list has multiple FAT devices, any previousely
registered FAT device should be deregistered before registering
next FAT boot device, otherwise the function may not attempt boot
from next FAT device.One of the situations where this issue can be
observed is when the boot device list has two FAT partitions of a
memory device and if booting fails on first partition (because of
file or partition related errors), boot from next partition actually
gets attempted on previous boot device only, as the previous device
has remained marked as registered. Call the function that invalidates
cached boot device in case of failure in booting from current FAT
boot device.
Signed-off-by: Prasad Kale <prasad.kale@live.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Sean Anderson <seanga2@gmail.com>
Align the implementation to rsa_add_verify_data() by writing the modulus
and r-squared properties with the same length as the key itself. This
fixes signature verification issues when one of the parameters has
leading zeros.
Reported-by: Hans Gfirtner (Nokia) <hans.gfirtner@nokia.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Technically, commit 24bf44cf88 ("spl: fit: Do not fail immediately if
an overlay is not available") introduced that regression as the code
will never advance if spl_fit_get_image_name() will return an error. But
at that time, spl_fit_get_image_node() was used in spl_fit_append_fdt()
which calls fdt_subnode_offset() to get the image node. And I presume
the commit was about the latter failing gracefully and trying the next
one.
But with commit b13eaf3bb4 ("spl: fit: Add board level function to
decide application of DTO") that behavior changed and the loop in
spl_fit_append_fdt() no longer uses spl_fit_get_image_node() but
spl_fit_get_image_name() directly. Thus it doesn't make any sense to not
break the loop if that fails.
Also, the original use case of commit 24bf44cf88 ("spl: fit: Do not
fail immediately if an overlay is not available") is preserved because
spl_subnode_offset() is now called within the loop and errors are
handled gracefully (and advancing the index).
Fixes: b13eaf3bb4 ("spl: fit: Add board level function to decide application of DTO")
Signed-off-by: Michael Walle <mwalle@kernel.org>
In Azure, older pipelines such as ours do not default to a shallow fetch
but rather do a complete clone. This introduces a marginal time increase
in each task, but also more importantly takes up significant disk space.
We are now getting warnings in some cases about using more than 95% of
our available disk space so take this as a first easy step to resolve
that problem.
Signed-off-by: Tom Rini <trini@konsulko.com>
Rockchip boards may depend on a working MMC regulator in SPL to
successfully load FIT payload from MMC. Typically, these boards only
include the vmmc-supply regulator and not its vin-supply in SPL control
FDT.
The commit f98d812e53 ("power: regulator: Add vin-supply for GPIO and
Fixed regulators") breaks loading FIT from MMC in SPL on some of these
boards due to now requiring the vin-supply to be included in the SPL
control FDT.
The commit also strangely enables any found vin-supply in
regulator_common_of_to_plat() and not when a regulator is enabled or as
part of regulator_autoset().
Revert the commit to fix FIT loading in SPL on broken boards.
If a board needs to have its vin-supply enabled, two options come to
mind:
- Add regulator-always-on prop to the regulator in the -u-boot.dtsi for
any board.
- Implement full support for reference counting of regulators and then
update the regulator-uclass to enable any found vin-supply when a
regulator is enabled.
This reverts commit f98d812e53.
Reported-by: Dang Huynh <danct12@riseup.net>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
If CONFIG_GPIO_HOG is not set, then gpio_hog_lookup_name() is empty,
and thus does not initialize any of its parameters. It does still
return 0 though, and so any calling function might assume that the
parameters have been initialized successfully.
Change the return value to -ENODEV in this case, as the function
would in the case when CONFIG_GPIO_HOG is set but the gpio hog
could not be found.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Heiko Schocher <hs@nabladev.com>
In devices where the U-Boot is used as a secondary bootloader, we rely
on the device's primary bootloader to implement CNTFRQ_EL0. However,
this reliance may lead to a non-functional timer in broken firmware.
For instance, some versions of Samsung's S-Boot don't implement it. It's
also not possible to set it in the U-Boot, because it's booted in a lower
exception level. CNTFRQ_EL0 is reported to be 0.
Use gd->arch.timer_rate_hz to override the queried value if set. This
setting needs to be done in the board file, preferrably in timer_init().
This feature is present only when the CONFIG_ARMV8_CNTFRQ_BROKEN is
enabled.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Now that we have a test for QEMU using transfer list from the previous
stage, there are two platforms testing this particular infrastructure. A
problem with the vexpress_fvp platform emulation in Gitlab is that we
often run it on hosts that are fast enough that we run in to a race
condition when trying to acquire the console and the test fails. Remove
both vexpress_fvp tests from Gitlab (they can remain in Azure) to remove
these spurious failures.
Signed-off-by: Tom Rini <trini@konsulko.com>
This also incorporates the following commits to the Dockerfile:
da7942de29 Dockerfile: remove Python 2.7
183299d9a4 docker: add OP-TEE and TF-A build for testing Firmware Handoff
Signed-off-by: Tom Rini <trini@konsulko.com>
Add qemu_arm64_tfa_fw_handoff test entries to azure and gitlab
pipelines.
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Check the existence of bl1 and fip from:
1. /opt/tf-a/${board_type}_${board_ident}, if not exist, then;
2. /opt/tf-a/${board_type}
This change allows to test with TF-A with specified board ID only.
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Firmware Handoff tests will leverage the same board type 'qemu_arm64'
with a new board ID 'fw_handoff_tfa_optee', thus select CMD_BLOBLIST
in qemu_arm64_defconfig for running the test.
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add test cases to validate FDT and TPM eventlog handoff from TF-A
and OP-TEE via bloblist.
For FDT, the nodes 'reserved-memory' and 'firmware' appended by
OP-TEE indicates a successful handoff.
For TPM eventlog, the events 'SECURE_RT_EL3', 'SECURE_RT_EL1_OPTEE'
and 'SECURE_RT_EL1_OPTEE_EXTRA1' created by TF-A indicates a
successful handoff.
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Fetch OP-TEE (4.7.0), TF-A (v2.13.0), MbedTLS (v3.6) and build
bl1 and fip with both Firmware Handoff and Measured Boot enabled.
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Acked-by: Jerome Forissier <jerome.forissier@linaro.org>
mem_map_from_dram_banks calls fdtdec_setup_memory_banksize to setup the
dram banks though that is expected to be done by dram_init_banksize as
part of board_r sequence.
This has the side effect of modifying gd->bd->bi_dram as well, therefore
this patch removes the call and updates spl_enable_cache for K3 to call
dram_init_banksize.
Signed-off-by: Anshul Dalal <anshuld@ti.com>
Reported-by: Francesco Dolcini <francesco@dolcini.it>
Closes: https://lore.kernel.org/u-boot/20251027165225.GA71553@francesco-nb/
Fixes: fe2647f2a0 ("arm: armv8: mmu: add mem_map_from_dram_banks")
Tested-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Add boot support and peripherals like eMMC/SD, UART, I2C, GPIO, ENETC0/1
and PCIE0/1 for iMX95 15x15 LPDDR4X EVK.
Updated doc for build instructions.
Signed-off-by: Ye Li <ye.li@nxp.com>
Add -u-boot.dtsi for iMX95 15x15 EVK used by SPL and binman.
iMX95 15x15 EVK uses LPDDR4X which needs dedicated DDR FW.
Signed-off-by: Ye Li <ye.li@nxp.com>
The factory provides a CPU UID in the OTPs and the SoM module
and the carrier board might provide additional UIDs in the GP
registers of the OTPs. Load these values in the following order
and create a serial number string:
* Board UID (GP2)
* SoM UID (GP1)
* CPU UID (UNIQUE_ID)
The string is stored in the "serial#" env variable and
exported to Linux. Further this prints the used UID to the
console which looks like this
ID: 0042152331 (Board)
or:
ID: 0030124840 (SoM)
or:
ID: 4696668CD9516886 (CPU)
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The factory provides a CPU UID in the OTPs and the SoM module
and the carrier board might provide additional UIDs in the GP
registers of the OTPs. Load these values in the following order
and create a serial number string:
* Board UID (GP2)
* SoM UID (GP1)
* CPU UID (UNIQUE_ID)
The string is stored in the "serial#" env variable and
exported to Linux. Further this prints the used UID to the
console which looks like this
ID: 0042152331 (Board)
or:
ID: 0030124840 (SoM)
or:
ID: 4696668CD9516886 (CPU)
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The factory provides a CPU UID in the OTPs and the SoM module
and the carrier board might provide additional UIDs in the GP
registers of the OTPs.
Provide a common function to load UIDs from arbitrary OTP
registers and generate a serial number string that is saved
in the "serial#" env variable.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Recently code was added in board_late_init() to autostart fastboot
in case of booting from USB OTG. This change was ineffective as
enabling CONFIG_BOARD_LATE_INIT got lost during upstreaming.
Fixes: 410d9ccc03 ("imx: kontron-sl-mx6ul: Autostart fastboot if booted from USB")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
