- Add the button command patch, update MAINTAINERS entry for a platform,
fix a problem with the hash command, fix a problem on K3 platforms and
revert a change on verdin-am62.
With the relatively new button API in U-Boot, it's now much easier to
model the common usecase of mapping arbitrary actions to different
buttons during boot - for example entering fastboot mode, setting some
additional kernel cmdline arguments, or booting with a custom recovery
ramdisk, to name a few.
Historically, this functionality has been implemented in board code,
making it fixed for a given U-Boot binary and requiring the code be
duplicated and modified for every board.
Implement a generic abstraction to run an arbitrary command during boot
when a specific button is pressed. The button -> command mapping is
configured via environment variables with the following format:
button_cmd_N_name=<button label>
button_cmd_N=<command to run>
Where N is the mapping number starting from 0. For example:
button_cmd_0_name=vol_down
button_cmd_0=fastboot usb 0
This will cause the device to enter fastboot mode if volume down is held
during boot.
After we enter the cli loop the button commands are no longer valid,
this allows the buttons to additionally be used for navigating a boot
menu.
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Tegra30
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
AM64 ES2.0 bootrom seems to enable WAIT0EDGEDETECTION interrupt.
This causes a lockup at A53 SPL when accessing NAND controller
or ELM registers.
A good option would be to softrest GPMC block at probe
but this cannot be done for AM64 as SOFTRESET bit is marked
as reserved in SYSCONFIG register.
Fix the issue by disabling all IRQs at probe.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Some platforms (such as the Lichee Pi 4A) have their dwmac device
addressable only in high memory space. Storing the node's base address
on 32 bits is not possible in such case.
Use platform's physical address type to store the base address.
Signed-off-by: Nils Le Roux <gilbsgilbert@gmail.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Rework the section about includes slightly. We should not be using
common.h anywhere, so remove that from examples and ask people to send
patches removing it when found. Doing this also means we need to reword
other parts of this section. Be clearer about using alphabetical
ordering.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
The error message
Adding disk for usb_mass_storage.lun0 failed (err=-9223372036854775788/0x8000000000000014)
provides a decimal and a hexadecimal notation of the EFI status code
EFI_ALREADY_STARTED which is defined as (EFI_ERROR_MASK | 20).
The decimal output does not convey the value 20 clearly.
With the patch we write
Adding block device usb_mass_storage.lun0 failed, r = 20
similar to other EFI error messages.
Fixes: 952018117a ("dm: sandbox: Switch over to using the new host uclass")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Probing the MU is needed to prevent this error in the SPL:
ele dev is not initialized
Authenticate container hdr failed, return -19, resp 0x0
IND = INVALID
ele dev is not initialized
Error: release container failed, resp 0x0!
IND = INVALID
SPL: failed to boot from all boot devices
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Recent i.MX8MP DTs use new fsl,imx6ul-ecspi compatible string instead
of the fsl,imx51-ecspi compatible string. Add the new compatible string
to fix ECSPI operation on i.MX8MP.
For details, see Linux:
48d74376fb68 ("arm64: dts: imx8mp: update ecspi compatible and clk")
8eb1252bbedf ("spi: imx: remove ERR009165 workaround on i.mx6ul")
Fixes: 451799a6ce ("arm: dts: imx8mp: Sync the DT with kernel 6.4-rc4")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
The SPL clock code does configure the ECSPI clock frequency, which has
to match the mxc-spi driver configuration for successful SPI NOR boot.
Drop the assigned-clock from DT ecspi1 node on this board to let the
SPL clock code do the configuration and keep it aligned with the driver
expectation.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add Renesas R8A779H0 V4M DT extras for U-Boot.
Until the RPC node becomes part of main DT, keep it here as
an extension so that board code can enable and use the RPC
to access SPI NOR.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Add PLL7 support to Gen3/Gen4 common clock driver. Add initial PLL7
multiplier and divider values into table in R8A779H0 V4M clock driver.
The PLL7 is new PLL added in R8A779H0 V4M SoC. Only integer multiplication
mode is supported by PLL7. The PLL reference clock are either 16.66 MHz or
20 MHz on R8A779H0 V4M SoC, and the output frequency must be 2000 MHz. The
multiplier values fitting this requirement are calculated to 120 or 100.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
These select/imply settings are common to the whole architecture not just
these boards, move these settings to the architecture config.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
TI KS2 boards have the nfs command in their common environment boot
configuration, enable this command.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
- Add USB support for phycore-imx8mp
- Fix environment corruption, reset on mx6sabresd
- Print reset cause on imx8
- Extend mkimage to support generating an image for i.MXRT FlexSPI
- Add new apalis and colibri variants
- Add support for phyBOARD-Segin-i.MX93 support
- Fix when FEC is primarily used instead of EQOS on i.MX93.
add support for Serial Downloader Boot via UUU as well as flashing emmc
via UUU on USB0 Port of phyBOARD Pollux.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>
