With the relatively new button API in U-Boot, it's now much easier to
model the common usecase of mapping arbitrary actions to different
buttons during boot - for example entering fastboot mode, setting some
additional kernel cmdline arguments, or booting with a custom recovery
ramdisk, to name a few.
Historically, this functionality has been implemented in board code,
making it fixed for a given U-Boot binary and requiring the code be
duplicated and modified for every board.
Implement a generic abstraction to run an arbitrary command during boot
when a specific button is pressed. The button -> command mapping is
configured via environment variables with the following format:
button_cmd_N_name=<button label>
button_cmd_N=<command to run>
Where N is the mapping number starting from 0. For example:
button_cmd_0_name=vol_down
button_cmd_0=fastboot usb 0
This will cause the device to enter fastboot mode if volume down is held
during boot.
After we enter the cli loop the button commands are no longer valid,
this allows the buttons to additionally be used for navigating a boot
menu.
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Tegra30
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Rework the section about includes slightly. We should not be using
common.h anywhere, so remove that from examples and ask people to send
patches removing it when found. Doing this also means we need to reword
other parts of this section. Be clearer about using alphabetical
ordering.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Sonoff iHost is gateway device designed to provide a Smart Home Hub,
it is based on Rockchip RV1126. There is also a version with 2GB RAM
based off the RV1109 dual core SoC however this works with the same
config as the RV1126 for uboot purposes.
Features:
- Rockchip RV1126
- 4GB DDR4
- 8GB eMMC
- microSD slot
- RMII Ethernet PHY
- 1x USB 2.0 Host
- 1x USB 2.0 OTG
- Realtek RTL8723DS WiFi/BT
- EFR32MG21 Silabs Zigbee radio
- Speaker/Microphone
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add documentation to introduce the Falcon Mode on RISC-V.
In this mode, the boot sequence is SPL -> OpenSBI -> Linux kernel.
Signed-off-by: Randolph <randolph@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Pull request efi-2024-04-rc1-4
Documentation:
* uefi: remove ".py" suffix for pytest.py command
* correct date in migration plan for CONFIG_DM
UEFI:
* fix conflicting SPDX license in RISC-V EFI linker scripts
* page align EFI binary section in RISC-V EFI binaries
* separate .data and .text sections of RISC-V EFI binaries
* use common function to get EFI configuration table
Add details regarding scheme which need to be followed in SPL and
further stages for those regions which need to be preserved across
bootstages.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium>
Add info regarding splash screen, video, bloblist and GPIO related
Kconfigs which were missing in the documentation.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium>
That's most probably a typo, because driver model design documents seem
to be from 2012 and there is no 2010.01 release.
Fixes: 282ed24fb3 ("dm: MIGRATION: Add migration plan for CONFIG_DM")
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Update the RGxx3 documentation to note that it now supports the
RG-ARC-D, RG-ARC-S, Powkiddy RK2023, and Powkiddy RGB30. Also update
verbiage around panel detection to note that it is no longer hard coded
to the RG503.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Documentation:
* add generated index to table of contents
* create index entries for commands
* update Python packages used to build the documentation
* fix typos in dfu documentation
UEFI:
* split unrelated code from efi_bootmgr.c
* rename CONFIG_BOOTEFI_BOOTMGR to CONFIG_EFI_BOOTMGR
* net: tftp: remove explicit EFI configuration dependency
* fs: remove explicit EFI configuration dependency
Other:
* Add Goldfish RTC driver and make it available on RISC-V QEMU
Such a config option does not exist. Rephrase, and avoid mentioning
MEM_SUPPORT_64BIT_DATA, which is an implementation detail.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Update requirements.txt to most current packages as produced by
python3 -m pip install six sphinx-rtd-theme sphinx-prompt
python3 -m pip freeze
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reword some sentences, add missing periods and fix various typos in the
dfu documentation.
This was originally contributed on [1]
[1] 9a21ed8ba7
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Now that the cp command is changed to use memmove() internally, update
the documentation to explicitly state that overlapping regions are
allowed.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Qualcomm architecture changes:
* Move clock and pinctrl drivers out of mach-snapdragon
* Various clock driver improvements
* Convert PMIC power/reset key driver to use the button API
* Preparetory work for migrating to upstream DT
Linux DTs stuff a value indicating if the USID is a USID or a GSID in the
reg property, the Linux SPMI driver then reads the two address cells
separately. U-boot's dev_read_addr() doesn't know how to handle this, so
use ofnode_read_u32_index() to get just the USID.
The Qcom pmic driver doesn't have support for GSID handling, so just
ignore the second value for now.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The core and chnl register ranges were swapped on SDM845. Fix it, and
fetch the register ranges by name instead of by index.
Drop the cosmetic "version" variable and clean up the debug logging.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The "Sending patches" and "Patman patch manager" documents refer to the
three-dash, "---", that separates patch parts. The symbol is written in
the documentation in the same form as it is in actual patches: as three
U+002D HYPHEN-MINUS characters. When building the documentation, Sphinx
converts this symbol to a U+2014 EM DASH, that is invalid in this case.
Make the three-dash symbol a reStructuredText inline literal to prevent
its conversion; that is, enclose it in a pair of double backquotes (`).
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
With latest coreboot (e.g.: v4.22.01), the instructions to enable
graphics support has changed. Refresh the doc.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Add brief documentation on how to build a bootable U-Boot image for the
phyGATE-Tauri-L.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Reviewed-by: Teresa Remmet <t.remmet@phytec.de>
Adjust the underline length so that it matches the title length.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add properties to improve eye diagram which sometimes need adjust
some parameters of u2phy;
Add a property to tune disconnect threshold;
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Add support for the Variscite VAR-SOM-IMX93 evaluation kit. The SoM
consists of an NXP iMX93 dual A55 CPU. The SoM is mounted on a Variscite
Symphony SBC.
Signed-off-by: Mathieu Othacehe <m.othacehe@gmail.com>
Standard passage provides for a bloblist to be passed from one firmware
phase to the next. That can be used to pass the devicetree along as well.
Add an option to support this.
Tests for this will be added as part of the Universal Payload work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
