Add support for the self-test continue command in the TPM v1.2 emulator,
to match the functionality in the TPM v2 emulator.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This reverts commit 159b6f0e11.
Since commit 159b6f0e11 ("caam: Fix CAAM error on startup") the following
regression was reported by Tim Harvey:
"I've found that this patch causes a regression on an imx8mm board
(imx8mm_venice_defconfig) where the first call to caam_rng_read fails
here in jr_dequeue but if you call it again it works. With some
debugging added:
SEC0: RNG instantiated
...
Hit any key to stop autoboot: 0
u-boot=> rng list
RNG #0 - caam-rng
u-boot=> rng 0 10
caam_rng_read caam-rng len=16
run_descriptor_jr_idx idx=0
Error in SEC deq: -1
caam_rng_read_one run_descriptor_jr failed: -1
caam_rng_read caam-rng caam_rng_read_one failed: -5
Reading RNG failed
u-boot=> rng 0 10
caam_rng_read caam-rng len=16
run_descriptor_jr_idx idx=0
00000000: ad 2e ad c0 2a 12 27 c4 65 82 66 19 be ef f6 07 ....*.'.e.f.....
If I revert your patch caam_rng_read works initially and on subsequent
calls."
" I ran into this when I was testing
lwIP HTTPS as it causes anything that uses dm_rng to fail the first
time (such as HTTPS)."
Revert it for now to avoid the regression.
Reported-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
The val (the bits to set) is the second member of the reg_data structure
and mask the third one. We obviously want to clear bits 6 and 7 in order
to only set bit 7 in there instead of only clearing bit 7 in order to
write bits 6 and 7 (which makes no sense).
Fortunately, according to the datasheet, bit 6 value doesn't matter when
bit 7 is set so this is essentially just a cosmetic change, no intended
change in behavior.
Fixes: f172575d92 ("power: rk8xx: add support for RK806")
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Allows use of the regulator functions of the RK8XX PMIC in SPL, which is
necessary to support the functionality of the Rockchip IO-domain driver
on relevant platforms.
Signed-off-by: Justin Klaassen <justin@tidylabs.net>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Allows use of the Rockchip IO-domain driver in SPL to configure
the GPIO to match the voltage supplied by specific regulators
(e.g. "vcc_sdio").
Signed-off-by: Justin Klaassen <justin@tidylabs.net>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Log the value of the regulators during initialization of the IO-domain
driver to aid in debugging GPIO voltage configuration problems.
Signed-off-by: Justin Klaassen <justin@tidylabs.net>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The RAM_ROCKCHIP_DEBUG can be used only if DEBUG_UART is
available.
The next commit introduces changes in definition of debug
uart functions, so that DEBUG_UART is required to be defined
in order to initialize uart and use print functions.
Signed-off-by: Lukasz Czechowski <lukasz.czechowski@thaumatec.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
The high-speed UART from MediaTek supports baudrate accuracy
compensation when using high-speed mode 3.
This is done by calculating the first digit of the fraction part of
sample count value. The fraction value will be then used as the
reference to insert 0 to 10 sample cycle(s) to one frame (assume
that frame format is 8n1, i.e. 10 bits per frame).
The fracdiv_[l/m] registers are used to determine whether a bit in one frame
should be inserted with one sample cycle.
With typical 40MHz source clock, the actual baudrates with/without
accuracy compensation are:
Ideal w/o compensation w/ compensation
======== ================ ===============
9600 9603 9600
115200 114942 115207
921600 930232 921659
3000000 3076923 3007519
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Fix UART register names and offsets according to the programming
guide to allow implementing some enhanced features.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This clears UHS_MODE_SELECT for timing modes <= MMC_HS_52.
When initializing to HS400 mode, the host controller downgrades to non-uhs
modes so clear UHS_MODE_SELECT at modes <= MMC_HS_52.
This fixes eMMC writes on j7200 EVM.
Fixes: 6067aa66b3 ("mmc: am654_sdhci: Add am654_sdhci_set_control_reg")
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
implement a driver to use semtech pinctrl and
gpio expander, this driver is adapted from a
existent linux driver that is written by
Gregory Bean <gbean@codeaurora.org>.
Signed-off-by: Anis Chali <chalianis1@gmail.com>
More Qualcomm fixes for 2025.07
* Adjust fdtfile logic to support more boards
* Support linux,code variable in qcom-pmic button driver
* Minor CLK API adjustments and apq8096/msm8916 fixes
* vbus regulator register fixes
* dragonboard410c KASLR support and other fixes
Tom Rini <trini@konsulko.com> says:
Hey all,
Related to my other series I've posted recently on cleaning up some
headers, this series here is the result of at least lightly auditing the
#includes used in include/[a-m]*.h. This ignores subdirectories, as at
least in part I think the top-level includes we've constructed are the
most likely places to have some extra transitive include paths. I'm sure
there's exceptions and I'll likely audit deeper once this first pass is
done. This only gets as far as "include/m*.h" because I didn't want this
to get too big. This also sets aside <miiphy.h> and <phy.h>. While
miiphy.h does not directly need <phy.h> there are *so* many users and I
think I had half of the tree just about not building when I first tried.
It might be worth further investigation, but it might just be OK as-is.
Link: https://lore.kernel.org/r/20250521230119.2084088-1-trini@konsulko.com
The value of "ETH_ALEN" is defined to 6 in <linux/if_ether.h>. This file
is included in <net.h>. In the places where we had ETH_ALEN but no
direct include of <net.h>, add <linux/if_ether.h>. In the places where
we had a custom name used, make use of ETH_ALEN instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
There are only a few things found in <mtd.h> today. Go through and audit
the C files which include <mtd.h> and remove it when not required. Then,
add it to the files which had either missed it or had an indirect
inclusion of it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This file does not need <linux/sizes.h> nor <linux/compiler.h> so remove
them. This exposes however that a number of other files had been relying
on this implicit include for <linux/sizes.h> so add that where needed.
Signed-off-by: Tom Rini <trini@konsulko.com>
Most device vendors put "Volume Down" button onto PMIC RESIN.
But Sony is special: see
dts/upstream/src/arm64/qcom/sdm630-sony-xperia-nile.dtsi or [1].
They put "Volume Down" on PMIC GPIO 7 where others usually put
"Volume Up", and KEY_VOLUMEUP is inside &pon_resin.
Currently if you boot U-Boot on such Sony device, you end up
with 2 "Volume Down" buttons, and no "Volume Up", which makes
navigating menu problematic.
Support reading devicetree "linux,code" property and override
statically defined button code & label based on that.
[1] https://elixir.bootlin.com/linux/v6.15-rc3/source/arch/
arm64/boot/dts/qcom/sdm630-sony-xperia-nile.dtsi#L263
Signed-off-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Signed-off-by: Alexey Minnekhanov <alexeymin@minlexx.ru>
Reviewed-by: Casey Connolly <casey.connolly@linaro.org>
Link: https://lore.kernel.org/r/20250424014811.3809818-1-alexeymin@minlexx.ru
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
As of commit dc8754e8e4 ("clk/qcom: apq8016: improve clk_enable logging")
there are now warnings in the U-Boot console on DragonBoard 410c:
apq8016_clk_enable: unknown clk id 122
apq8016_clk_enable: unknown clk id 123
apq8016_clk_enable: unknown clk id 124
apq8016_clk_enable: unknown clk id 125
This is because we don't implement enable() properly for the SDCC clocks.
Currently they are being enabled as part of set_rate().
Fix this by moving the enable calls out of the apq8016_clk_init_sdc()
function and convert them to the equivalent GATE_CLK_POLLED() definitions.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Reviewed-by: Casey Connolly <casey.connolly@linaro.org>
Link: https://lore.kernel.org/r/20250424-apq8016-clock-fixes2-v2-6-fcc371c9e45f@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
GATE_CLK() in its current state is unsafe: A simple write to the clock
enable register does not guarantee that the clock is immediately running.
Without polling the clock status, we may issue writes to registers before
the necessary clocks start running. This doesn't seem to cause issues in
U-Boot at the moment, but for example removing the CLK_OFF polling in TF-A
for the SMMU clocks on DB410c reliably triggers an exception during boot.
Make it possible to poll the branch clock status register, by adding a new
GATE_CLK_POLLED() macro that takes the extra register address. Existing
usages work just as before, without polling the clock status. Ideally all
usages should be updated to specify the correct poll address in the future.
The Qualcomm naming for these clocks is "branch" and not "gate", but let's
keep the existing naming for now to avoid confusion until all others
drivers have been converted.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Reviewed-by: Casey Connolly <casey.connolly@linaro.org>
Link: https://lore.kernel.org/r/20250424-apq8016-clock-fixes2-v2-4-fcc371c9e45f@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
The SDCC_...(n) macros in clock-apq8016.c result in the wrong addresses:
- SDCC1: SDCC_APPS_CBCR(0) = ((0 * 0x1000) + 0x41018) = 0x41018
Should be 0x42018, this is an invalid register close to the USB clocks.
- SDCC2: SDCC_APPS_CBCR(1) = ((1 * 0x1000) + 0x41018) = 0x42018
Should be 0x43018, this is the SDCC1 clock.
When we try to enable SDCC2, we actually end up enabling SDCC1. When we try
to enable SDCC1, we just issue some broken register writes.
This hasn't caused any trouble so far, because the boot firmware is keeping
both SDCC clocks running. However, if these clocks are disabled when
entering U-Boot, MMC initialization is failing.
Fix this by using the proper offset for the macros. The SDCC_CMD_RCGR() was
already correct, but change it the same way for consistency.
Fixes: 085921368b ("arm: Add support for Qualcomm Snapdragon family")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Reviewed-by: Casey Connolly <casey.connolly@linaro.org>
Link: https://lore.kernel.org/r/20250424-apq8016-clock-fixes2-v2-1-fcc371c9e45f@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
u-boot-dfu-20250602
CI: https://source.denx.de/u-boot/custodians/u-boot-dfu/-/pipelines/26466
Usb gadget:
dwc2: Fix incorrect ULPI_UTMI_SEL bit setting
dwc2: Fix HBstLen setting for external DMA mode
dwc2: Various refactors to get the code closer to Linux
dwc2: Support reset logic for v4.20a
Change the return value for timeout errors in i2c-designware from 1 to
-ETIMEDOUT. Returning errors as negative values is standard practice in the
u-boot, which enhances error handling consistency across the codebase.
The current behavior can lead to silent errors when functions check for
negative return values to identify errors. For example, in
`dm_i2c_reg_read` from i2c-uclass.c, a timeout results in an uninitialized
value being returned, potentially causing unexpected behavior.
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Wojciech Szamocki <wojciech.szamocki@nokia.com>
Signed-off-by: Wojciech Szamocki <wojciech.szamocki@nokia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
The bitshift in GEM_CLK_CTRL register is five bits, not two. There are
four bits for each GEM, and one bit reserved in between.
This has caused that using more than one GEM is impossible,
additionally corrupting the GEM0's configuration, leaving GEM0
unusable as well (ie. if GEM0 and GEM1 are used, GEM1 configuration is
going to write to GEM0's registers wrong value, leaving GEM0 unusable)
Signed-off-by: Frantisek Bohacek <rutherther@ditigal.xyz>
Link: https://lore.kernel.org/r/20250522060703.4863-1-rutherther@ditigal.xyz
Signed-off-by: Michal Simek <michal.simek@amd.com>
The clock driver allows to boost the NAND performance
controller. Make changes to let it use the new clock driver
=> time nand read ${loadaddr} kernel
NAND read: device 0 offset 0x500000, size 0x800000
8388608 bytes read: OK
time: 0.488 seconds
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Make simple the clock registration and enable and allow later
to add support for other platforms
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Varadarajan Narayanan <quic_varada@quicinc.com> says:
The qcs9100 based Ride platforms have UFS as their primary storage.
Hence add support to U-Boot env framework to be able to save and
retrieve the environment from UFS. The environment will be
saved/retrieved from the partition specified in the config option
CONFIG_SCSI_ENV_PART.
Also add an API to convert partition UUID string to block device
descriptor for UFS. This API will be used to get the block device
descriptor for the partition specified in CONFIG_SCSI_ENV_PART.
Link: https://lore.kernel.org/r/20250513091710.3719292-1-quic_varada@quicinc.com
Tom Rini <trini@konsulko.com> says:
Hey all,
This is a v3 of Simon's series[1] and depends on the series[2] I posted
the other day that removes <env.h> from <command.h>. With this series
done, I believe we've tackled all of the current cases of headers which
include <env.h> without directly needing it. Much of this series is in
fact Simon's v2 with the main differneces being:
- Removing <env.h> from <net.h> at the end
- Removing env_to_ip() given how little it's used rather than shuffling
around where it's declared and un-inline'ing it. For a rarely used
helper, this ends up being cleaner I think. Especially looking at some
of the users (which called env_get repeatedly). If there's strong
opinion here about using the other method[3] we can do that instead.
- Setting aside for now how to handle CMD_ELF=y and NO_NET=y because
today it's actually fine as we unconditionally build lib/net_utils.c
where string_to_ip() is defined. I'm unsure if a further series is
warranted here or not. We rely on link-time optimization to keep code
readable too.
[1]: https://lore.kernel.org/all/20250501010456.3930701-1-sjg@chromium.org
[2]: https://lore.kernel.org/all/20250514225002.15361-1-trini@konsulko.com
[3]: https://lore.kernel.org/all/20250501010456.3930701-23-sjg@chromium.org
Link: https://lore.kernel.org/r/20250515234154.1859366-1-trini@konsulko.com
Now that env_get_ip() has been removed, the include file <net.h> does
not need anything from <env.h>. Furthermore, include/env.h itself
includes other headers which can lead to longer indirect inclusion
paths. To prepare to remove <env.h> from <net.h> fix all of the
remaining places which had relied on this indirect inclusion to instead
include <env.h> directly.
Reviewed-by: Jerome Forissier <jerome.forissier@linaro.org> # net/lwip
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
